SOMFY Sonesse 40 Manuel utilisateur

Instructions

Somfy Sonesse 40 Remote Control Programming

Programming Upper and Lower Limit Positions

NOTE: If you are using Somfy Telis 4 multi channel remote to programme more than one blind, start at

step 1. If you are using Somfy Telis 1 single channel remote to programme one blind, start at step 3.

1. Plug in power to the ﬁrst motor. The blind will jog (move up and

down brieﬂy). Make sure only the motor which is being programmed

is powered or ‘awake’.

2. Press the SELECTION button to select the channel on the handset to

be used for the blind. The indicator light for the corresponding

channel will come on for a few seconds and then turn off.

3. Press the UP and DOWN buttons simultaneously until the blind jogs.

4. Check the direction of the UP and DOWN buttons. When pressing

the UP button, the blind should go up. To change direction press and

hold the MY button until the blind jogs.

5. Set the limit positions. Use the UP and DOWN buttons to position

the blind so that it is at the desired upper limit/fully open position.

6. Brieﬂy press and release the MY and DOWN buttons simultaneously.

The blind will lower.

7. Press the MY button to stop the blind when it is approximately at the

lower limit/fully closed position.

8. Use the UP and DOWN buttons to position the blind so that it is

exactly at the desired lower limit/fully closed position.

9. Brieﬂy press and release the MY and UP buttons simultaneously. The

blind will move up and stop at the programmed upper limit/fully open

position.

10. To conﬁrm both limits press the MY button until the blind jogs.

11. Brieﬂy press and release the PROGRAMME button on the back of

the handset (using a screwdriver or sharp pencil). The blind will jog.

Your programming has been recorded.

12. If programming further blinds onto further channels, unplug the

power to the current blind before repeating these steps with the

next blind. Only when all blinds and channels have been programmed

can power to all blinds be plugged back in.

Copying Programmed Channel onto 5th Channel

You can copy the programming of channels 1 - 4 to channel 5 to operate all the blinds simultaneously.

1. Press the SELECTION button to select the channel to be copied.

2. Press and hold the PROGRAMME button on the back of the handset (using a screwdriver or

paperclip) until the blind jogs (moves up and down brieﬂy).

3. Press the SELECTION button to select channel 5 (when all four indicator lights are on).

4. Brieﬂy press the PROGRAMME button on the back of the handset. The blind will jog. Your

programming has been recorded.

5. Repeat steps 1- 4 to copy any further channels.

Programming the Intermediate ‘My’ Position

The My position allows you to set the blind at your favourite position.

1. Press the UP and DOWN buttons to move the blind to the desired position.

2. Press and hold the MY button for approximately 5 seconds until the blind jogs. Your ‘My’ position

has been recorded.

Deleting the ‘My’ Position

1. Press the MY button to move the blind to the programmed ‘My’ position.

2. Press and hold the MY button for approximately 5 seconds until the blind jogs. Your ‘My’ position

has been deleted.

Adjusting the Up and Down Limits

1. Leave the blind at its current upper limit position if you want to adjust the upper limit position, or its

current lower limit position if you want to adjust the lower limit position.

2. Press the UP and DOWN buttons simultaneously for approximately 5 seconds until the blind jogs.

3. Use the UP and DOWN buttons to adjust the blind to the new desired position.

4. To conﬁrm the new position, press and hold the MY button for approximately 2 seconds until the

blind jogs. Your new position limit has been recorded.

Factory Reset

If you want to erase all programming, you can perform a factory reset. Move the blind to the middle of

the window. Only switch off the current for the motor to be reset.

1. Cut the power supply for 2 seconds, then turn it back on and leave it on for 10-15 seconds.

2. Cut the power supply again for 2 seconds, then turn it back on again. The blind will move/jog for 5

seconds.

3. Press and hold the PROGRAMME button on the back of the handset until the blind jogs twice. All

programming will be reset to factory mode.

If you have any questions about programming, please call us.

Table des matières

Autres manuels SOMFY Télécommande

SOMFY

SOMFY HOME MOTION Chronis io Manuel utilisateur

SOMFY

SOMFY Telis 1 Lounge Manuel utilisateur

SOMFY

SOMFY Nina io Manuel utilisateur

SOMFY

SOMFY nina Manuel utilisateur

SOMFY

SOMFY KEYPOP 2 RTS Manuel utilisateur

SOMFY

SOMFY SITUO 5 io/RTS PURE Manuel utilisateur

SOMFY

SOMFY FREEROLL RTS Manuel utilisateur

SOMFY

SOMFY myLink Manuel utilisateur

SOMFY

SOMFY Telis Composio io Manuel utilisateur

SOMFY

SOMFY Telis 5 Modulis RTS Silver 1810663 Manuel utilisateur

SOMFY

SOMFY 1875157 Manuel utilisateur

SOMFY

SOMFY Telis RTS Manuel utilisateur

SOMFY

SOMFY 5014984 Manuel utilisateur

SOMFY

SOMFY INTEO TELIS 1 RTS Manuel utilisateur

SOMFY

SOMFY Centralis RTS Manuel utilisateur

SOMFY

SOMFY IRS 300 Manuel utilisateur

SOMFY

SOMFY Situo 1 Soliris RTS II Manuel utilisateur

SOMFY

SOMFY Situo 1 io Manuel utilisateur

SOMFY

SOMFY CENTRALIS RECEIVER Manuel utilisateur

SOMFY

SOMFY SITUO RTS Manuel utilisateur

SOMFY

SOMFY Telis 6 Chronis RTS Guide d'installation

SOMFY

SOMFY Telis 6 Chronis RTS Manuel utilisateur

SOMFY

SOMFY Oximo RTS Manuel utilisateur

SOMFY

SOMFY inis RT Manuel utilisateur

Manuels Télécommande populaires d'autres marques

Panasonic

Panasonic EUR7622KB0 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen Beo4 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur

Multiplex

Multiplex PROFI TX 9 Manuel utilisateur

One Remote

One Remote RMB4 Manuel utilisateur

FUTABA

FUTABA 9ZAP - PART2 Manuel utilisateur

HR Matic

HR Matic HR MULTI 3 Manuel utilisateur

Yamaha

Yamaha ACC-GNRST-30-20 Manuel utilisateur

EisSound

EisSound KBSOUND Manuel utilisateur

Marantz

Marantz RC101 Manuel utilisateur

Conrad

Conrad FS20 TC6 Manuel utilisateur

Anritsu

Anritsu MP1777A Manuel utilisateur

Niles

Niles WVC100 Guide de dépannage

RCA

RCA RCU1300 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen BEO6 Manuel utilisateur

GE 94901 Manuel utilisateur

Onbon

Onbon YQ1-75 Manuel utilisateur

FUTABA

FUTABA R7108SB Instructions d'installation