SOMFY IRS 300 Manuel utilisateur
INSTALLATIONguide
General description :
The IRS 300 is an infra-red remote control system.
It is a control system designed for controlling all types of
interior blinds (exept for curtains and vertical blinds),
powered by 24Vdc motors from the LT28 or the Concept 25
line.
It is capable of controlling eight different blinds individually or
as a group and has many sophisticated functions.
IRS 300 INFRARED RECEIVER
Characteristics :
Technical data :
Nominal supply : 24 Vdc
Minimum supply : 20 Vdc
Maximum supply : 35 Vdc
IP rating : IP00
Working temperature : 0°C to 50°C
Output relay : 3A
Housing colour/material : White/ABS
Net weight : 65g
Dimensions : 76 x 50 x 32mm
1
In compliance with the requirement.
OPTIONS -
IRT 103 individual control function.
IRT 803 multi-channel remote control with individual
or master control functions (one to eight blinds).
WARNING! : The IRT 803 is the sole programming
tool for the IRS 300.
Impulse switch connection for use without remote
control (individual or master control).
The IRS 300 is compatible with the IRT 103 & IRT 803
infrared transmitters.
The IRS 300 is initially
configured to operate with
the IRT103 transmitter or
the IRT 803 without a
channel selected.
®
12
34
56
78
PROG.
IRT 803
1 ➟8 1 ➟45➟8
®
R
24 Vdc
+
_
D C Motors D C Motors
24 Vdc
+
_
Individual Control
Individual Control
IRS 300 IRS 300
General Control
2
Installation :
Mounting :
A
The IRS 300 has to be installed indoor.
1. Drill a hole in the wall at the desired location using a 5mm drill bit
(depth 25mm) and insert the supplied raw plug.
2. Place the screw supplied into the securing hole on the face of the
IRS 300 and feed into the raw plug.
3. Fix the IRS 300 unit by securing the screw.
SCREW
IRS 300
WALL
RAW PLUG
IRT 103 - To tilt the slats, press and hold one of the corresponding buttons (up or down).
To raise or lower the blind, momentarily press the corresponding button (up or down).
To stop the blind press the stop button.
IMPULSE - To raise or lower the blind, momentarily press the corresponding button (up or down).
SWITCH To stop the blind, press the stop button or push the up and down buttons simultaneously.
IRT 803 - To tilt the slats, press and hold one of the corresponding buttons (up or down).
To raise or lower the blind, momentarily press the corresponding button (up or down).
Point the transmitter at the Infra-red sensor which corresponds to the receiver you wish to control.
12
34
56
78
12
34
56
78
If you wish to control one
receiver, press the
corresdponding button of the
channel you have selected.
Then you can control the
receiver by pressing the
buttons : UP , DOWN or
STOP.
34
56
78
1 ➟8 1 ➟45➟8
If you wish to control a
group of receivers, press on
the corresponding button :
1..4 5..8 1..8
>>
R
Operation :
C
Wiring :
B
Enter the programming mode
Press and hold for at least 5 seconds the «prog »button on the IRT 803 transmitter.
The blind concerned, at it alone, will start to tilt up & down quickly.
Warning : If you use the IRT803, it is necessary to « lock » the receivers which are not being programmed by operating
them in either UP or DOWN direction (they will be locked for 3 minutes and it is impossible to enter in the programming
mode by the IRT803). To unlock them, give a STOP order.
PROG.
1 ➟8 1 ➟45➟8
®
Exit from the programming mode
Press momentarily the «prog »button on the IRT 803 transmitter. The blind stops
tilting.
PROG.
1 ➟8 1 ➟45➟8
®
3
Important : Carry out this operation as near as possible to the receiver of the blind that you wish to program.
PROG.
1 ➟8 1 ➟45➟8
®
34
56
78
1 ➟8 1 ➟45➟8
34
56
78
1 ➟8 1 ➟45➟8
Enter the
programming mode.
The blind starts
tilting up & down.
Press the 8 button.
The blind stops
tilting.
Press the button
Exit the programming
mode by pressing the «
prog »button.
1..8
To cancel and revert back to IRT 103 transmitter operation.
a
> >
PROG.
1 ➟8 1 ➟45➟8
®
12
34
12
34
56
78
Enter the
programming mode.
The blind starts
tilting up & down.
Press the 1 button.
The blind stops
tilting.
Press the corresponding
button of the desired
channel (1, 2......8).
How to choose a channel (IRT 803 only):
b
>>
The channel is now
assigned. The blind will
start tilting up & down
quickly again.
Proceed with another
setting for this blind or
exit the programming
mode.
>
PROG.
1 ➟8 1 ➟45➟8
®
12
34
56
78
2
4
6
Enter the
programming mode.
The blind starts
tilting up & down.
Press the 5 button.
The blind starts tilting
slowly.
To set tilting speed:
Increase speed by pressing up.
Decrease speed by pressing
down.
How to set the tilting speed:
c
>>
Press the button
to confirm.
The blind starts tilting up
& down quickly again.
Proceed with another
setting for this blind or
exit the programming
mode.
>
5..8
Programming :
R
4
R
The Blind won’t move
1- Check the battery level of the transmitter.
2- Check the low voltage feed of the IRS 300 (inversion between the + and -).
3- Check if there is a bright light shining on the receiver.
4- Check that you are within the infrared transmission range.
5- Check that you are aiming the transmitter at the receiver correctly.
Up and Down is
reversed when
operating with the
transmitter.
1- Check the motor wiring.
PROG.
1 ➟8 1 ➟45➟8
®
12
34
56
2
4
6
Enter the
programming mode.
The blind starts
tilting up & down.
Press the 3 button. Let
the blind rise to the full
up position. Press the
down button, (the blind
goes down).
Press the stop button
as soon as the down
position is reached.
How to set the automatic opening of the slats in the down position:
d
>>>
2
4
6
8
2
4
To change this setting
once it is programmed :
Press the «down »
button. The blind moves
to the down position.
Press and hold the «
up »button until the
desired opening is
reached.
>>
Press the button
to confirm.
The blind starts tilting up
& down quickly again.
Proceed with another
setting for this blind or
exit the programming
mode.
5..8
2
4
Press and hold the «
up »button until the
desired opening is
reached.
How to re-program the
automatic opening of the
slats in the down
position.
Press the «prog »
button and start the
operation again.
PROG.
1 ➟8 1 ➟45➟8
®
12
34
12
34
56
Enter the
programming mode.
The blind starts
tilting up & down.
Press the 2 button.
The blind stops tilting.
Press the 1 button. The
blind starts tilting up &
down quickly again.
How to cancel the tilting function? - (Roller - Pleated - Cellular Blind Types).
e
>> >
PROG.
1 ➟8 1 ➟45➟8
®
Press the «prog »
button to exit the
programming
mode.
Up and Down is
reversed when
operating with the
impulse type switch.
1- Check the motor wiring.
2- Check the impulse switch wiring.
3- Check the switch wiring on the input connector of the IRS 300.
Manfunctions :
Autres manuels SOMFY Télécommande
SOMFY
SOMFY KEYGO Manuel utilisateur
SOMFY
SOMFY Impresario Chronis RTS Manuel utilisateur
SOMFY
SOMFY SITUO 1 VARIATION Instructions d'utilisation et d'entretien
SOMFY
SOMFY Telis 1 io Manuel utilisateur
SOMFY
SOMFY Telis 1 Lounge Manuel utilisateur
SOMFY
SOMFY Easy Sun io Manuel utilisateur
SOMFY
SOMFY nina Manuel utilisateur
SOMFY
SOMFY KEYTIS INTERIOR Manuel utilisateur
SOMFY
SOMFY Telis Composio RTS Manuel utilisateur
SOMFY
SOMFY Situo 1 RTS Instructions d'utilisation et d'entretien
SOMFY
SOMFY 1810632 Telis 1 RTS Pure Manuel utilisateur
SOMFY
SOMFY SITUO 5 io/RTS PURE Guide d'installation
SOMFY
SOMFY INTEO TELIS 4 RTS Manuel utilisateur
SOMFY
SOMFY Smoove Origin RTS US Manuel utilisateur
SOMFY
SOMFY Telis 1 Lounge Manuel du propriétaire
SOMFY
SOMFY SITUO 5 io/RTS PURE Manuel utilisateur
SOMFY
SOMFY Situo 5 io Manuel utilisateur
SOMFY
SOMFY Telis 5 Modulis RTS Silver 1810663 Manuel utilisateur
SOMFY
SOMFY Telis 4 Soliris RTS Manuel utilisateur
SOMFY
SOMFY Telis 6 Chronis RTS Guide d'installation
Manuels Télécommande populaires d'autres marques
Panasonic
Panasonic EUR7622KB0 Manuel utilisateur
Bang & Olufsen
Bang & Olufsen Beo4 Manuel utilisateur
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur
Multiplex
Multiplex PROFI TX 9 Manuel utilisateur
One Remote
One Remote RMB4 Manuel utilisateur
FUTABA
FUTABA 9ZAP - PART2 Manuel utilisateur
