Solid State Logic E Series Manuel utilisateur

-1-

E Series Dynamics Module

for 500 Series Racks

User Guide

-2-

Safety and Installation Considerations

This page contains denitions, warnings, and practical information to ensure a safe

working environment. Please take time to read this page before installing or using this

apparatus.

General Safety

• Read these instructions.

• Keep these instructions.

• Heed all warnings.

• Follow all instructions.

• Do not use this apparatus near water.

• Do not expose this apparatus to rain or moisture.

• Clean only with dry cloth.

• Do not block any ventilation openings.

• Install in accordance with the rack manufacturer’s instructions.

• There are no user-adjustments, or user-servicable items, on this apparatus.

• Adjustments or alterations to this apparatus may affect the performance such

that safety and/or international compliance standards may no longer be met.

• This apparatus is not to be used in safety critical applications

Caution

• This apparatus should not be used outside of the scope of API 500 series

compatible racks.

• Do not operate this apparatus with any covers removed.

• To reduce the risk of electric shock, do not perform any servicing other than that

contained in these Installation Instructions unless you are qualied to do so. Refer

all servicing to qualied service personnel.

Installation

• Ensure power is removed from the rack before tting or removing this apparatus to

or from the rack.

• Use the panel xing screws supplied with the rack to secure this apparatus into the

rack.

-3-

Standards Compliance

This apparatus is designed to be installed and used in API

500 series compatible racks which are CE marked. The CE

mark on a rack is indicative that the manufacturer conrms

that it meets both EMC and the Low Voltage Directive

(2006/95/EC).

Instructions for Disposal of WEEE by Users in the

European Union

The symbol shown here is on the product or on its

packaging, which indicates that this product must not

be disposed of with other waste. Instead, it is the user’s

responsibility to dispose of their waste equipment by

handing it over to a designated collection point for recycling of

waste electrical and electronic equipment. The separate collection

and recycling of your waste equipment at the time of disposal will

help to conserve natural resources and ensure that it is recycled

in a manner that protects human health and the environment.

For more information about where you can drop off your waste

equipment for recycling, please contact your local city ofce, your

household waste disposal service or where you purchased the

product.

Limited Warranty

Please refer any warranty claim to the supplier of this equipment in

the rst instance. Full warranty information for equipment supplied

directly by Solid State Logic can be found on our website:

www.solidstatelogic.com

-4-

Introduction

Congratulations on your purchase of this API 500 series compatible

SSL E Series Dynamics module.

This module has been specically designed to operate in an

API 500 series rack such as the API lunchbox® or equivalent. In

common with many such modules, the nominal input/output level is

+4dBu.

Your new module comprises a compressor/limiter and an expander/

gate, the design of which returns faithfully to the circuit and key

components which dened the sound of the original SSL E Series

channel strip. A true RMS converter is used in the side chain whilst

the gain element is an all discrete design identical to the Class A

VCA chip used in the original.

The compressor contains additional switching options to defeat the

over-easy curve and to use a linear release instead of the more

usual logarithmic curve. The result is a compressor with three

distinct voicings, all of which contributed to the many classic records

tracked and mixed on early E Series consoles.

As well as replicating the feel of the classic E Series dynamics,

this module provides, with the exception of access to a ‘link’ bus,

the same facilities as the SSL X-Rack XR418 E Series Dynamics

module.

Operation

Please refer to the illustration opposite.

The IN button , located centre left, switches the entire module

in and out of circuit.

The two vertical rows of LEDs , located centre right, provide

an indication of dynamics activity. The row of green LEDs to the

left show Gate/Expander activity whilst those to the right indicate

operation of the Compressor/Limiter.

-5-

1 2

-6-

Compressor/Limiter

When turned to 1:1, the compressor/limiter section

is inactive. Turning the control clockwise increases

the compression ratio, giving a true limiter at the fully

clockwise position. The compressor normally has

an ‘over-easy’ characteristic – pressing the button re-

places this with a ‘hard knee’ characteristic, providing

an alternative for some instruments.

Whenever a signal exceeds the level set by this

control, the compressor will start to act at the ratio set

by the RATIO control. The THRESHold and RATIO

controls also provide automatic make-up gain, so as

you lower the threshold and introduce more com-

pression, the output level is increased, maintaining

a steady output level regardless of the amount of

compression.

Changes the release curve from logarithmic to linear.

This also raises the threshold by 6dB.

Provides a faster attack time (3mS for 20dB gain re-

duction). When off the attack time is slower and less

aggressive (30mS for 20dB gain reduction).

Sets the time constant (speed) with which the

compressor returns to normal gain settings once the

signal has passed its maximum.

RATIO

THRESH

LIN REL

FAST ATT

RELEASE

-7-

Gate/Expander

This section can act as a 20:1 Gate or as a 2:1 Expander when the

EXP button is pressed.

Determines the depth of gating or expansion. When

turned fully anti-clockwise, this section is inactive.

When turned fully clockwise, a gate depth or range of

40dB can be obtained.

Determines the level at which the gate opens or

the level below which gain reduction begins (EXP

selected), adjustable from +4dBu to –26dBu.

Variable hysteresis is incorporated in the threshold

circuitry which increases as the threshold is lowered.

This is very useful in music recording as it allows

instruments to decay below the ‘open’ threshold

before gating or expansion takes place.

Normally, a controlled linear attack time of 1.5ms

per 40dB is provided. Press this button to select a

fast attack time (100µs per 40dB). The attack time

is the time taken for the Gate/Expander to ‘open’

once the signal level is above the threshold. When

gating signals with a steep rising edge, such as

drums, a slow attack may effectively mask the initial

‘THWACK’, so you should be aware of this when

selecting the appropriate attack time.

This determines the time constant (speed), variable

from 0.1 to 4 seconds, at which the Gate/Expander

reduces the signal level once it has passed below

the threshold.Note that this control interacts with the

RANGE control.

RANGE

THRESH

FAST ATT

RELEASE

-8-

Visit SSL at:

www.solidstatelogic.com

SSL® and Solid State Logic® are ® registered trademarks of Solid State Logic.

ORIGIN™, SuperAnalogue™, VHD™ and PureDrive™ are trademarks of Solid State

Logic.

All other product names and trademarks are the property of their respective owners and

are hereby acknowledged.

No part of this publication may be reproduced in any form or by any means, whether

mechanical or electronic, without the written permission of Solid State Logic, Oxford, OX5

1RU, England.

As research and development is a continual process, Solid State Logic reserves the right

to change the features and specications described herein without notice or obligation.

Solid State Logic cannot be held responsible for any loss or damage arising directly or

indirectly from any error or omission in this manual.

PLEASE READ ALL INSTRUCTIONS, PAY SPECIAL HEED TO SAFETY WARNINGS.

E&OE

July 2020

Revision History

Revision V2.0, June 2020 - Revised Layout Release for Module Update

Table des matières

Autres manuels Solid State Logic Unité de contrôle

Solid State Logic

Solid State Logic SSL G Series Manuel utilisateur

Solid State Logic

Solid State Logic E Series Manuel utilisateur

Solid State Logic

Solid State Logic B Series Manuel utilisateur

Solid State Logic

Solid State Logic XLOGIC SUPERANALOGUE X-RACK Stereo EQ Manuel utilisateur

Solid State Logic

Solid State Logic SiX Channel 500 Series Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur