Socket CX2881-1476 Manuel utilisateur

QUICK START GUIDE

CHS 8Ci

Bluetooth Cordless Scanner

This document pertains to the following model:

CHS 8Ci - Black SKU# CX2881-1476 (P/N 8550-00069)

CHS 8Ci - White SKU# CX2893-1497 (P/N 8550-00072)

PACKAGE CONTENTS

trademarks or trademarks of Socket Mobile, Inc. The Bluetooth word mark and logo are

registered trademarks of the Bluetooth SIG, Inc. USA, and any use by Socket Mobile, Inc.

is under license. All other trademarks and trade names contained herein may be those of

their respective owners.

CHS 8Ci Lanyard USB Charging Cable

PRODUCT INFORMATION

PRODUCT SPECIFICATIONS

Light Source 630nm +- 30nm visible red LED

Scan Rate 5 scans / sec

Sensor Linear CMOS sensor

Resolution 5mil / 0.127mm

Bluetooth Prole SPP, HID

Battery Life 8 hours (1 scan / 5 sec)

Charge Time 4 hours fully charged

Wireless Range 10M / 33ft line of sight

Operating Temp 0° to 50° C (32° to 122° F)

Symbologies All major 1D barcodes

CHARGE THE BATTERY

Charge the CHS

The CHS must be fully charge before rst use. Initial charging takes 4

hours with the USB charging cable connected to a USB charging port.

Insert the Micro USB side of the USB Charging Cable (included) into

the CHS port and the USB side of the Charging Cable into the USB con-

nector of an AC adapter (not included). The CHS will beep twice when

connected to a USB Charging Port.

Power On

Press and hold down the small power button until the CHS beeps (low-

high tone).

See below for instructions on pairing and connecting your scanner

with your Apple or Android devices.

4 Hours

GETTING STARTED

Successful Scanning

1. Hold the scanner 5-7 cm away

from the barcode.

2. Aim the scan beam straight

across the entire barcode.

3. Keep your hand steady!

BLUETOOTH MODE  HID  SPP  iOS

The CHS 8Ci supports three modes of Bluetooth wireless

communication: HID, SPP, and iOS.

By default, the CHS 8Ci is set to HID Keyboard mode.

Operating System Apple Android Windows

HID ✓✓✓

SPP ✓ ✓

iOS ✓

HID (Human Interface Device): Default mode. No software installation

required.

SPP (Serial Port Prole): Recommended for Android, Windows

and other operating systems. Allows two-way communications.

SocketScan 10 software (available at socketmobile.com) or another

third party SDK application is required.

iOS: Recommended for Apple. Allows two-way communications.

Compatible application developed with SocketScan 10 SDK required.

Learn more about HID and SPP at http://www.socketmobile.com/

pdf/techbrief/socketscan-10-sdk_white-paper.pdf 7

BLUETOOTH BASICS

Pair and Connect

When Bluetooth is activated on your device and the CHS is in

discoverable mode, Bluetooth pairing will begin. When the two devices

recognize each other, they can pair.

Once the devices have paired, it is necessary to connect. (Follow the

instructions in the following pages to connect the CHS to your device.)

Once the devices have connected, they will automatically recognize

each other whenever they are within range, and it will not be

necessary to connect again.

If the CHS is connected to a device and gets disconnected, it will try to

reconnect. Make sure the computer or device is on and in range. If the

CHS cannot reconnect, it will beep long. Power o then on again to

reconnect.

To unpair from the last connected host, press and hold the trigger

button while turning o the scanner.

The CHS 8Ci keeps the pairing information of the last connected host.

Power o to disconnect the scanner, then power on to reconnect the

scanner.

To disconnect your CHS:

1. Power o - press and hold down the power button until the CHS

beeps (high-low tone).

2. Power on - press and hold down the power button until the CHS

beeps (low-high tone).

Your CHS is ready to reconnect.

BLUETOOTH BASICS

APPLE  BLUETOOTH MODE HID (KEYBOARD EMULATION)

Connect your CHS with an Apple device using HID mode.

(HID is the default mode.)

1. Power on the CHS.

2. Scan this barcode to set the CHS to HID mode.

3. Enable Bluetooth on the Apple device. A Bluetooth device search

will begin.

4. Select Socket CHS in the list of found devices.

5. Tap Pair if prompted.

6. The CHS will beep once to conrm connection.

Now you are ready to scan barcodes in HID mode using your Apple

device!

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Socket Scanner

Socket

Socket CHS 7P Manuel utilisateur

Socket

Socket DURASCAN D800 Series Manuel utilisateur

Socket

Socket Secure Digital Scan Card Series 3 Manuel utilisateur

Socket

Socket CompactFlash Scan Card Series 5 Manuel utilisateur

Socket

Socket CHS 7DiRx Manuel d'installation

Socket

Socket DURASCAN 800 Series Manuel utilisateur

Socket

Socket Cordless Ring Scanner Series 9 Manuel utilisateur

Socket

Socket Cordless Ring Scanner Series 9 Manuel utilisateur

Socket

Socket CHS 8Ci Manuel utilisateur

Socket

Socket 7X Manuel utilisateur

Socket

Socket Bluetooth iPAQ Manuel utilisateur

Socket

Socket CompactFlash Scan Card Series 5 Manuel utilisateur

Socket

Socket 1D Manuel utilisateur

Socket

Socket CHS 7XiRx Manuel utilisateur

Socket

Socket CHS 7Xi Manuel utilisateur

Socket

Socket CF RFID Reader-Scan Card Series 6 Manuel utilisateur

Socket

Socket Secure Digital Scan Card Series 3 Manuel utilisateur

Socket

Socket CRS Series 9 Manuel utilisateur

Socket

Socket Cordless Ring Scanner Series 9 Manuel utilisateur

Socket

Socket Cordless Hand Scanner Manuel utilisateur

Socket

Socket CHS Series 7 Manuel utilisateur

Socket

Socket CHS 7Ci Manuel utilisateur

Socket

Socket CHS Series 7 Manuel utilisateur

Socket

Socket 7X Manuel utilisateur

Manuels Scanner populaires d'autres marques

Plustek

Plustek Scanner Manuel utilisateur

Z/I Imaging

Z/I Imaging PhotoScan 2001 Manuel utilisateur

Renkforce

Renkforce DS100-5M Manuel utilisateur

Image Access

Image Access WideTEK A2 Manuel utilisateur

Canon

Canon imageFORMULA CR-120N Manuel utilisateur

Fujitsu

Fujitsu FI-4860C2 Manuel utilisateur

GeoSlam

GeoSlam ZEB Horizon Instructions d'installation

Kodak

Kodak i5800 Scanner Manuel utilisateur

Kodak

Kodak i7300 Manuel utilisateur

Revopoint

Revopoint POP Manuel utilisateur

Fujitsu

Fujitsu fi-4860C Manuel utilisateur

Eddyfi Technologies

Eddyfi Technologies Floormap X Manuel utilisateur

Faselase

Faselase F6 Manuel utilisateur

Fujitsu

Fujitsu CardMinder Manuel utilisateur

Uniden

Uniden BC340CRS Manuel utilisateur

Infinite Peripherals

Infinite Peripherals INFINEA TAB M Manuel utilisateur

Mustek

Mustek PageExpress 4800 Pro Manuel utilisateur

Optex

Optex 750830 Manuel utilisateur