Snom 710 Manuel utilisateur

http://www.elastix.org

Snom 710 and Elastix Server

Setup Guide

PaloSanto Solutions

Snom 710 Server Setup Guide

1.0 Setup Diagram

Figure 1-1 is a setup diagram for a single IP Phone Snom 710 configuration. The phone

is setup as a SIP telephony device.

Figure 1-1. Setup Diagram

2.0 Host PC Environment

Table 2-1. Host Server Environment Details

Description

Hardware Type

Elastix Appliance ELX-Series

Hardware Version

ELX-3000

Software Type

Elastix

Software Version

2.4

3.0 Test Setup Equipment

Table 3-1. Test Setup Equipment

Equipment

Model

Version

IP (SIP) Phone

N/A

Snom

710

8.7.3.25

Switch

N/A

PaloSanto Solutions

Snom 710 Server Setup Guide

4.0 Setup Procedure

To set up the Elastix Server for the Snom 710,

1. Go to the web address of the Elastix Server Login page. The web address is

determined by the customer, for this guide we have used the IP address

192.168.1.75

2. On the Login page, type the username and password for an administrative user into

the Username and Password fields, see Figure 4-1. The username and password are

determined by the customer.

Figure 4-1. Login

3. Press Enter or click on the Submit button to go to Elastix‟s Dashboard

4. Once inside, click on the PBX tab on the menu at the top of the screen

Figure 4-2. Dashboard

PaloSanto Solutions

Snom 710 Server Setup Guide

5. Click on the Submit button to add an extension, see Figure 4-3. This will take you

to the Add SIP Extension page.

Figure 4-3. Add an Extension

6. On the Add SIP Extension page (Figure 4-4), fill in the following information:

• User Extension (301 in this example)

• Display Name ( “Snom710” in this example)

• secret (“h7Dka3Rf9si0t”in this example)

Figure 4-4. Add SIP Extension

7. Click on the „Submit‟ button at the end of the page. The extension will be created

and you will see the page on Figure 4-5 displaying the “Apply Configuration

Changes Here” pink ribbon on top of the screen.

8. Click in the “Apply Configuration Changes Here” link

PaloSanto Solutions

Snom 710 Server Setup Guide

Figure 4-5. Apply Configuration Changes Here

9. With this you have just finished creating a SIP extension that will be used by the

Snom 710 to register with the Elastix Server. Repeat Steps 5 through 8 to similarly

create another extension (different values on Step 6) to be used by the IP (SIP)

Phone to register as well (extension 302 in this example). Once finished you will

see something similar to Figure 4-6

Figure 4-6. Snom and IP Phone extensions successfully created

10. To register the Snom Phone, you will need to enter the information from the

extension created on the Elastix Server into the Snom Phone by logging into the

Snom 710 WebUI.

To register the Snom Phone there are two methods: Manual Configuration and

AutoProvisioning using Elastix’s Endpoint Configurator.

PaloSanto Solutions

Snom 710 Server Setup Guide

MANUAL CONFIGURATION

1. Log in to the Snom 710 WebUI by pointing your browser to the Snom Phone‟s IP

address.

For the initial configuration, refer to the Snom 710 User Manual found at:

http://wiki.snom.com/Snom710/Documentation

Factory default settings

IP Addressing

DHCP

Web Access User Name

Not set

Web Access Password

Not set

11. When the WebUI is loaded, use the information from the Add SIP Extension page

(Figure 4-4) to enter the following necessary information on “Setup => Identity 1

=> Login” section of the Snom Phone WebUI (Figure 4-7):

Identity active: ON

Displayname: (SnomPhone in this example)

Account: (301 in this example)

Password: (“h7Dka3Rf9si0t”in this example)

Registrar: Elastix Server‟s IP Address (192.168.1.75 in this example)

Outbound Proxy: Elastix Server‟s IP Address (192.168.1.75 in this example)

Authentication Username: (301 in this example)

Mailbox: *97

Figure 4-7. Account Configuration

12. Once you have entered the required information, click on „Save‟ button. Now, go to

“Setup => Identity 1 => RTP”. The “RTP Encryption” option should be set to “off”.

Apply and save changes. (Figure 4-8).

PaloSanto Solutions

Snom 710 Server Setup Guide

Figure 4-8. RTP

13. To check the correct registration of the account, go to “Status => System

Information” section (Figure 4-9). If it‟s not registered, make sure you‟ve entered

the correct information.

Figure 4-9. System Information

14. Configure the other IP (SIP) Phone with the correct parameters.

15. To test the Snom 710, pick up the previously configured IP (SIP) Phone and call

the Snom 710‟s extension number (301 in this example). When the call is

established, speak into the phone and verify that the other IP (SIP) Phone can hear

your voice. Check this by calling from both ends.

PaloSanto Solutions

Snom 710 Server Setup Guide

AUTOPROVISIONING USING ELASTIX‟S ENDPOINT

CONFIGURATOR

Note: The support for Endpoint Configurator is available in Elastix 2.4 by installing the

new Endopoint configurator module. This new module is already included in Elastix

2.5.

1. For Elastix 2.4, log in to the console and install the module by entering the

command:

yum -y install elastix-endpointconfig2

2. After installation, in the Elastix Web Interface go to “PBX => Batch Configurations

=> New Endpoint Configurator”. See figure 4-10

Figure 4-10. New Endpoint Configurator

3. Type the network address where the phone is located and click on the magnifying

glass. This will generate a list with all the phones available in that network. See

figure 4-11.

Figure 4-11. List of endpoints

4. In the row where the phone you want to autoprovision is located (find it according

to either its MAC or IP Address):

Mark the checkbox

From the drop-down list, select the correct Phone Model if it is not detected

automatically

Click on the link “[Configure x.x.x.x]” to set the parameters to configure the

phone.

PaloSanto Solutions

Snom 710 Server Setup Guide

5. After clicking in the configuration link, you will see a window with many tabs

according to what you want to configure. In this case we will configure a SIP

account. Go to the tab “Accounts” and drag the accounts you want to assign from

left to right. Then click on Apply button. See figure 4-12.

Figure 4-12. Accounts configuration

6. After configuring you will see that the status field of the phone has changed. See

figure 4-13

Figure 4-13. List of endpoints

7. Now with the phones selected, click on the button “Apply Configuration” located

next to the magnifying glass button. A message will be shown saying the operation

was successful. See figure 4-14.

PaloSanto Solutions

Snom 710 Server Setup Guide

Figure 4-14. Configuration successful

8. Your phone will reboot, and when it boots up it should be registered with Elastix

with the accounts you set. This step completes the procedure.

Autres manuels pour 710

Table des matières

Autres manuels Snom Téléphone IP

Snom

Snom M3 Manuel utilisateur

Snom

Snom 4S Media Server Manuel d'utilisation et d'entretien

Snom

Snom Vodafone 821 Manuel utilisateur

Snom

Snom D785N Manuel utilisateur

Snom

Snom 320 Instructions d'utilisation d'origine

Snom

Snom D715 Manuel utilisateur

Snom

Snom Mass Deployment V7 Manuel utilisateur

Snom

Snom D760 Series Manuel utilisateur

Snom

Snom 320 Manuel utilisateur

Snom

Snom 320 Manuel d'instructions

Snom

Snom 190 Version V3.00 Manuel utilisateur

Snom

Snom D717 Manuel utilisateur

Snom

Snom D375 Manuel utilisateur

Snom

Snom UC edition 760 Manuel utilisateur

Snom

Snom 320 Manuel utilisateur

Snom

Snom 320 Manuel utilisateur

Snom

Snom 300 Instructions d'utilisation d'origine

Snom

Snom 360 Instructions d'utilisation d'origine

Snom

Snom 720 Manuel utilisateur

Snom

Snom 870 Manuel utilisateur

Snom

Snom 300 Manuel utilisateur

Snom

Snom Vodafone 821 Manuel utilisateur

Snom

Snom C520 WiMi Instructions d'utilisation

Snom

Snom D865 Fiche d'information produit

Manuels Téléphone IP populaires d'autres marques

Alcatel

Alcatel 4028 Manuel utilisateur

Polycom

Polycom Polycom VVX 600 Manuel utilisateur

Polycom

Polycom SoundPoint IP 450 Manuel utilisateur

Cisco

Cisco SPA-500 Series Manuel utilisateur

Polycom

Polycom SoundPoint IP 650 Manuel utilisateur

Proximus

Proximus Maestro 3016 IP Manuel utilisateur

Fanvil

Fanvil X4 Manuel utilisateur

Cisco

Cisco 7962 Manuel utilisateur

Yealink

Yealink Yealink SIP-T46G Manuel utilisateur

Avaya

Avaya 4625SW Manuel utilisateur

Yealink

Yealink SIP-T52S Manuel utilisateur

Nortel

Nortel 1140E Manuel utilisateur

Nexotek

Nexotek NT-P500 Manuel utilisateur

Avaya

Avaya Integral 5 R3.0 Manuel utilisateur

GE 28320EE2 - Dect 6.0 InfoLink 2 Manuel utilisateur

Avaya

Avaya 4600 Series Manuel de service

Mitel

Mitel MIVOICE OFFICE 400 6940 SIP Manuel utilisateur

Nortel

Nortel i2050 Manuel utilisateur