Smeg KSEIV97X Manuel utilisateur

LibrettoIstruzioni

InstructionManual

Manueld’Instructions

Bedienungsanleitung

Gebruiksaanwijzing

ManualdeInstrucciones

NL 42

DE 32

FR 22

GB 12

IT 2

ES 52

KSEIV97X

12GB

CONTENTS

Dear Customer,

If you follow the recommendations

contained in this Instruction Manual,

your appliance will give you constant

high performance and will remain

efficient for many years to come.

RECOMMENDATIONSANDSUGGESTIONS 13

CHARACTERISTICS 14

INSTALLATION 16

USE 19

MAINTENANCE 20

13GB

RECOMMENDATIONS AND SUGGESTIONS

INSTALLATION

• The manufacturer will not be held liable for any damages resulting

from incorrect or improper installation.

• The minimum safety distance between the cooker top and the

extractor hood is 650 mm.

• Check that the mains voltage corresponds to that indicated on the

rating plate fixed to the inside of the hood.

• For Class I appliances, check that the domestic power supply

guarantees adequate earthing.

Connect the extractor to the exhaust flue through a pipe of

minimum diameter 120 mm. The route of the flue must be as short

as possible.

• Do not connect the extractor hood to exhaust ducts carrying

combustion fumes (boilers, fireplaces, etc.).

• Iftheextractorisused in conjunctionwith non-electrical appliances

(e.g. gas burning appliances), a sufficient degree of aeration must

be guaranteed in the room in order to prevent the backflow of

exhaust gas. The kitchen must have an opening communicating

directly with the open air in order to guarantee the entry of clean

air.

USE

• The extractor hood has been designed exclusively for domestic

use to eliminate kitchen smells.

• Never use the hood for purposes other than for which it has ben

designed.

• Never leave high naked flames under the hood when it is in

operation.

• Adjust the flame intensity to direct it onto the bottom of the pan

only, making sure that it does not engulf the sides.

• Deep fat fryers must be continuously monitored during use:

overheated oil can burst into flames.

• The hood should not be used by children or persons not instructed

in its correct use.

MAINTENANCE

• Switch off or unplug the appliance from the mains supply before

carrying out any maintenance work.

• Clean and/or replace the Filters after the specified time period.

• Clean the hood using a damp cloth and a neutral liquid detergent.

650 mm min.

14GB

CHARACTERISTICS

Dimensions

650 min.

680

470

290

898

565

132

433

150

350

740

940

15GB

7.1a

7.1

12h

7.1b

2.1

2.2

8b 8a

12c

12g

12f

12e

12c

14.1

Components

Ref. Q.ty Product Components

11 Hood Body, complete with: Controls, Light,

Blower, Filters

21 Telescopic Chimney comprising:

2.1 1 Upper Section

2.2 1 Lower Section

7.1 1 Telescopic frame complete with extractor,

consisting of:

7.1a 1 Upper frame

7.1b 1 Lower frame

8a 1 Right Air Outlet Grill

8b 1 Left Air Outlet Grill

10 1 Damper

14 1 Hood BodyAir Outlet Extension Piece

consisting of two Half Shells

14.1 1 Air Outlet Connection Extension

15 1 Air Outlet Connection

24 1 Junction box

25 2 Pipe clamps

Ref. Q.ty Installation Components

11 4 Wall Plugs ø 10

12c 6 Screws 2,9 x 6,5

12e 2 Screws 2,9 x 9,5

12f 4 Screws M6 x 10

12g 4 Screws M6 x 80

12h 4 Screws 5,2 x 70

21 1 Drilling template

22 4 6.4 mm int. dia washers

23 4 M6 nuts

Q.ty Documentation

1 Instruction Manual

16GB

INSTALLATION

Drilling the Ceiling/shelf and fixing the frame

DRILLING THE CEILING/SHELF

• Use a plumb line to mark the centre of the hob on the ceiling/support shelf.

• Place the drilling template 21 provided on the ceiling/support shelf, making sure that the template

is in the correct position by lining up the axes of the template with those of the hob.

• Mark the centres of the holes in the template.

• Drill the holes at the points marked:

• For concrete ceilings, drill for plugs appropriate to the screw size.

• For hollow brick ceilings with wall thickness of 20 mm: drill ø 10 mm.

• For wooden beam ceilings, drill according to the wood screws used.

• For wooden shelf, drill ø 7 mm.

• For the power supply cable feed, drill ø 10 mm.

• For the air outlet (Ducted Version), drill according to the diameter of the external air exhaust

duct connection.

FIXING THE FRAME

Before fixing, separate the Upper Section 2.1 and

the Lower Section 2.2 from the Frame by

unscrewing the screws 12c, then separate the two

sections of the frame by unscrewing the 8 side

screws to obtain the Upper frame and Lower fra-

me.

17GB

14.1

ø 150

Upper frame

• Align the power supply cable feed hole

• Fix the upper frame to the ceiling or shelf using:

• For concrete ceilings, use the appropriate plugs for the screw size (not provided).

• For hollow brick ceilings of wall thickness of approximately 20 mm: use 4 plugs 11 and 4

screws 12h (5,2 x 70), provided.

• For wooden beam ceilings, use 4 wood screws (not provided).

• For wooden shelf, use 4 screws 12g (M6 x 80) with washers 22 and nuts 23, provided.

Lower frame

• Fix the lower frame using the 8 previously removed screws, adjusting the length according to the

installation height (hood body lower fixing surface must be at least 710 mm from the hob).

• For the recirculation version, turn the frame in the direction chosen for the recirculated air outlet.

• The frame mountings must be secure to withstand the weight of the hood and any stresses caused

by the occasional side thrust applied to the device. On completion, check that the base is stable,

even if the frame is subjected to bending.

• In all cases where the ceiling is not strong enough at the suspension point, the installer must

provide strengthening using suitable plates and backing pieces anchored to the structurally sound

parts.

Connections

DUCTED VERSION AIR EXHAUST SYSTEM

In order to install the ducted version, connect the hood to the chimney using either a flexible or rigid

pipe ø 150 mm, the choice of which is left to the installer.

• Push fit Damper 10 onto the air outlet.

• Fix the pipe using the pipe clamps 25 provided.

• Remove any activated charcoal filters.

RECIRCULATION VERSION AIR OUTLET

• Assemble the two halves of the hood body

extension piece 14.

• Push fit the assembled hood body extension

piece 14 onto the air outlet.

• Push fit connection 15 onto the hood body

extension piece 14.

• Insert the connection extension pieces laterally

14.1 in connection 15.

18GB

12f

8b 8a

12c

12e

Cmd

12c

Lux

Flue assembly - Mounting the hood body

• Position the upper chimney section and fix the

upper part to the frame using the 2 screws 12c

(2,9 x 6,5) provided.

• Similarly, position the lower chimney section

and fix the lower part to the frame using the 2

screws 12c (2,9 x 6,5) provided.

Recirculation version

• Makesure that the outlet of the extension pieces

14.1 is horizontally and vertically aligned with

the chimney outlets.

• Ifthis is not the case, remove the lower chimney

section and adjust the position by either

reversing the connection extension pieces 14.1

or by cutting the hood body extension 14 along

one of the thinner section channels denoting the

pre-fixed lengths, then reassemble as described

previously.

• Fit the directional grids 8a-8b in their housings

making sure that the directional symbols are

towards the top. Also make sure that they are

correctly inserted in the connection extension

pieces 14.1.

Before fixing the hood body to the frame:

• Remove the grease filters from the hood body.

• Remove any activated charcoal filters.

• From below, use the 4 screws 12f (M6 x 10)

provided to fix the hood body to the frame.

ELECTRICAL CONNECTION

• Connect the hood to the mains through a two-

pole switch having a contact gap of at least 3

mm.

• Connect the control connector Cmd.

• Connect the lights connector Lux.

• Place the connector in the junction box 24 and

close it using the 2 screws 12e (2,9 x 9,5)

provided.

• Fix the junction box to the hood body using the

2 screws 12c (2,9 x 6,5) provided.

• For the recirculation version, fit the activated

carbon odour filter.

• Replace the grease filters.

19GB

RV1 V2 V3

S1 S2

USE

Controlpanel

LLight Switches the lighting system on and off.

S1 Led Motor running led.

It flashes once after 100 working hours of the hood to indicate that the grease

filters need washing.

It flashes twice after 200 working hours to indicate that the grease filters need

washing and that the anti-odour charcoal filters, if any, need changing.

S2 Led Intensive speed led.

MMotor Switches the extractor motor on and off at low speed. Used to provide a

contin-uos and silent air change in the presence of light cooking vapours.

When the Hood is in ELC (Electronic Comfort) mode, the button will not only

turn the Ducting motor on, but will also disable this function.

V1 Speed Reduces the operating speed.

When the button is pressed with the Motor off, ELC (Electronic Comfort)

mode will be enabled again, giving a continuous, low noise flow of air. Press

the button and hold it until Led S1 flashes slowly.

V2 Speed Increases the operating speed.

V3 Intensive Maximum speed, used for eliminating the highest cooking vapour emission.

Speed Switches off automatically after 10 minutes operation. Can also be switched

off manually by pressing the button.

RReceiverfor Optional Remote Control.

Remote Control

20GB

MAINTENANCE

Greasefilters

CLEANING METAL SELF- SUPPORTING GREASE FILTERS

Alarm signal reset

• Switch off the lights and extractor motor.

• Press button V2 for at least 3 seconds, until the

leds start to flash.

Cleaning the filters

• The filters must be cleaned when led S1 flashes

or at least every 2 months of operation, or more

frequently for particularly heavy usage.

• Remove the filters one at a time by pushing

them towards the back of the group and pulling

down at the same time.

• Wash the filters, taking care not to bend them.

Allow them to dry before refitting.

• When refitting the filters, make sure that the

handle is visible on the outside.

Autres manuels pour KSEIV97X

Table des matières

Autres manuels Smeg hotte de ventilation

Smeg

Smeg KSMD910X1 Manuel technique

Smeg

Smeg CK2000LED Manuel utilisateur

Smeg

Smeg KD9X6-1 Manuel utilisateur

Smeg

Smeg KSEG77X-1 Manuel utilisateur

Smeg

Smeg KICV60BL Manuel utilisateur

Smeg

Smeg SAH490SS Manuel utilisateur

Smeg

Smeg KICGR52X Manuel utilisateur

Smeg

Smeg SHW610X1 Manuel utilisateur

Smeg

Smeg KSEG5 Manuel utilisateur

Smeg

Smeg KSG70E Manuel technique

Smeg

Smeg HOBD682D1 Manuel utilisateur

Smeg

Smeg KD61X2 Manuel utilisateur

Smeg

Smeg KSE912NX2 Manuel utilisateur

Smeg

Smeg KV26 Manuel utilisateur

Smeg

Smeg CA12SHRPX Manuel utilisateur

Smeg

Smeg K181X90 Manuel utilisateur

Smeg

Smeg KSET65 Manuel technique

Smeg

Smeg KASC505 Manuel utilisateur

Smeg

Smeg SHIG910X Manuel utilisateur

Smeg

Smeg K24X60 Manuel utilisateur

Smeg

Smeg KSEV905X Manuel technique

Smeg

Smeg KAT700HXE Manuel technique

Smeg

Smeg SHW910X Manuel utilisateur

Smeg

Smeg Portofino KPF9AN Manuel utilisateur

Manuels hotte de ventilation populaires d'autres marques

emmeti

emmeti RECUPA MED A-140 Mode d’emploi

Nibe

Nibe F135 Manuel utilisateur

Kuppersberg

Kuppersberg INTRO 60 Instructions d'installation et d'entretien

Zephyr

Zephyr Spruce AK9834BS Guide d'installation

Hisense

Hisense MH6INBG Manuel utilisateur

Miele

Miele DA 1255 Manuel utilisateur

Broan

Broan 46000 Manuel utilisateur

GE Profile PV977 Instructions originales

FALMEC

FALMEC FFRIA24W5FS Manuel utilisateur

Whirlpool

Whirlpool RH2600XL-1 SERIES Manuel utilisateur

Küppersbusch

Küppersbusch DX ISLA Manuel utilisateur

ETNA

ETNA AV360RVS Manuel utilisateur

JUNO

JUNO JDF603E6 Manuel utilisateur

Miele

Miele DA 6708 D Manuel utilisateur

Tricity Bendix

Tricity Bendix LE 150 Manuel

AEG

AEG X68163BV1 Manuel utilisateur

AEG

AEG 125 D Manuel utilisateur

Nibe

Nibe S Series Guide de l'utilisateur