SMC Networks EX260-SEN2-X205 Manuel utilisateur

No.EX※※-OMX1001

PRODUCT NAME

SI unit for EtherNet/IPTM

MODEL / Series / Product Number

EX260-SEN2-X205

-1- 
 No.EX※※-OMX1001 
 Table of Contents 
 Safety Instructions 2
Model Indication and How to Order 8
Summary of Product parts 9
Definition and terminology 10 
Installation and Wiring 11 
Installation 11 
Wiring 12 
LED Indication and Settings 16 
Hardware Configuration 19 
EDS file and icon 19 
Setting using RSLogix5000TM 19 
Setting using Network Configurator 24 
EtherNet/IPTM Device Level Ring (DLR) function 29 
EtherNet/IPTM QuickConnectTM function 29 
Web server function 31 
Troubleshooting and Maintenance 38 
Specifications 43 
Dimensions 46 

-2-

No.EX※※-OMX1001

Safety Instructions

These safety instructions are intended to prevent hazardous situations and/or equipment damage.

These instructions indicate thelevel ofpotential hazard with the labels of "Caution", "Warning" or "Danger".

They are all important notes for safety and must be followed in addition to International Standards

(ISO/IEC)*1), and other safety regulations.

*1) ISO 4414: Pneumatic fluid power -- General rules relating to systems.

ISO 4413: Hydraulic fluid power -- General rules relating to systems.

IEC 60204-1: Safety of machinery -- Electrical equipment of machines. (Part 1: General requirements)

ISO 10218: Manipulating industrial robots -Safety.

etc.

Caution

Caution indicates a hazard with a low level of risk which, if not avoided, could

result in minor or moderate injury.

Warning

Warning indicates a hazard with a medium level of risk which, if not avoided,

could result in death or serious injury.

Danger

Danger indicates a hazard with a high level of risk which, if not avoided, will

result in death or serious injury.

Warning

1. The compatibility of the product is the responsibility of the person who designs the

equipment or decides its specifications.

Since the product specified here is used under various operating conditions, its compatibility with specific

equipment must be decided by the person who designs the equipment or decides its specifications

based on necessary analysis and test results.

The expected performance and safety assurance of the equipment will be the responsibility of the person

who has determined its compatibility with the product.

This person should also continuously review all specifications of the product referring to its latest catalog

information, with a view to giving due consideration to any possibility of equipment failure when

configuring the equipment.

2. Only personnel with appropriate training should operate machinery and equipment.

The product specified here may become unsafe if handled incorrectly.

The assembly, operation and maintenance of machines or equipment including our products must be

performed by an operator who is appropriately trained and experienced.

3. Do not service or attempt to remove product and machinery/equipment until safety is

confirmed.

1. The inspection and maintenance of machinery/equipment should only be performed after measures to

prevent falling or runaway of the driven objects have been confirmed.

2. When the product is to be removed, confirm that the safety measures as mentioned above are

implemented and the power from any appropriate source is cut, and read and understand the specific

product precautions of all relevant products carefully.

3. Before machinery/equipment is restarted, take measures to prevent unexpected operation and malfunction.

4. Contact SMC beforehand and take special consideration of safety measures if the

product is to be used in any of the following conditions.

1. Conditions and environments outside of the given specifications, or use outdoors or in a place

exposed to direct sunlight.

2. Installation on equipment in conjunction with atomic energy, railways, air navigation, space, shipping,

vehicles, military, medical treatment, combustion and recreation, or equipment in contact with food and

beverages, emergency stop circuits, clutch and brake circuits in press applications, safety equipment or

other applications unsuitable for the standard specifications described in the product catalog.

3. An application which could have negative effects on people, property, or animals requiring special

safety analysis.

4. Use in an interlock circuit, which requires the provision of double interlock for possible failure by using

a mechanical protective function, and periodical checks to confirm proper operation.

-3-

No.EX※※-OMX1001

Safety Instructions

Caution

1.The product is provided for use in manufacturing industries.

The product herein described is basically provided for peaceful use in manufacturing industries.

If considering using the product in other industries, consult SMC beforehand and exchange

specifications or a contract if necessary.

If anything is unclear, contact your nearest sales branch.

Limited warranty and Disclaimer/Compliance Requirements

The product used is subject to the following "Limited warranty and Disclaimer" and "Compliance

Requirements".

Read and accept them before using the product.

Limited warranty and Disclaimer

1. The warranty period of the product is 1 year in service or 1.5 years after the product is

delivered, whichever is first.2)

Also, the product may have specified durability, running distance or replacement parts.

Please consult your nearest sales branch.

2. For any failure or damage reported within the warranty period which is clearly our

responsibility, a replacement product or necessary parts will be provided.

This limited warranty applies only to our product independently, and not to any other

damage incurred due to the failure of the product.

3. Prior to using SMC products, please read and understand the warranty terms and

disclaimers noted in the specified catalog for the particular products.

2) Vacuum pads are excluded from this 1 year warranty.

A vacuum pad is a consumable part, so it is warranted for a year after it is delivered.

Also, even within the warranty period, the wear of a product due to the use of the

vacuum pad or failure due to the deterioration of rubber material are not covered by the

limited warranty.

Compliance Requirements

1. The use of SMC products with production equipment for the manufacture of weapons of

mass destruction (WMD) or any other weapon is strictly prohibited.

2. The exports of SMC products or technology from one country to another are governed by

the relevant security laws and regulation of the countries involved in the transaction. Prior

to the shipment of a SMC product to another country, assure that all local rules governing

that export are known and followed.

-4-

No.EX※※-OMX1001

Operator

This operation manual is intended for those who have knowledge of machinery using pneumatic

equipment, and have sufficient knowledge of assembly, operation and maintenance of such

equipment. Only those persons are allowed to perform assembly, operation and maintenance.

Read and understand this operation manual carefully before assembling, operating or providing

maintenance to the product.

■Safety Instructions

Warning

■Do not disassemble, modify (including changing the printed circuit board) or repair.

An injury or failure can result.

■Do not operate the product outside of the specifications.

Do not use for flammable or harmful fluids.

Fire, malfunction, or damage to the product can result.

Verify the specifications before use.

■Do not operate in an atmosphere containing flammable or explosive gases.

Fire or an explosion can result.

This product is not designed to be explosion proof.

■If using the product in an interlocking circuit:

•Provide a double interlocking system, for example a mechanical system.

•Check the product regularly for proper operation.

Otherwise malfunction can result, causing an accident.

■The following instructions must be followed during maintenance:

•Turn off the power supply.

•Stop the air supply, exhaust the residual pressure and verify that the air is released before performing

maintenance.

Otherwise an injury can result.

Caution

■After maintenance is complete, perform appropriate functional inspections.

Stop operation if the equipment does not function properly.

Safety cannot be assured in the case of unexpected malfunction.

■Provide grounding to assure the noise resistance of the Serial System.

Individual grounding should be provided close to the product with a short cable.

-5-

No.EX※※-OMX1001

■NOTE

○Follow the instructions given below when designing, selecting and handling the product.

The instructions on design and selection (installation, wiring, environment, adjustment, operation,

maintenance, etc.) described below must also be followed.

Product specifications

•When conformity to UL is required, the SI unit should be used with a UL1310 Class 2 power supply.

•The SI unit is a "UL" approved product only if they have a mark on the body.

•Use the specified voltage.

Otherwise failure or malfunction can result.

•Reserve a space for maintenance.

Allow sufficient space for maintenance when designing the system.

•Do not remove any nameplates or labels.

This can lead to incorrect maintenance, or misreading of the operation manual, which could cause damage or

malfunction to the product.

It may also result in non-conformity to safety standards.

-6-

No.EX※※-OMX1001

Product handling

Installation

•Do not drop, hit or apply excessive shock to the fieldbus system.

Otherwise damage to the product can result, causing malfunction.

•Tighten to the specified tightening torque.

If the tightening torque is exceeded the mounting screws may be broken.

IP67 protection cannot be guaranteed if the screws are not tightened to the specified torque.

•Never mount a product in a location that will be used as a foothold.

The product may be damaged if excessive force is applied by stepping or climbing onto it.

Wiring

•Avoid repeatedly bending or stretching the cables, or placing heavy load on them.

Repetitive bending stress or tensile stress can cause breakage of the cable.

•Wire correctly.

Incorrect wiring can break the product.

•Do not perform wiring while the power is on.

Otherwise damage to the fieldbus system and/or I/O device can result, causing malfunction.

•Do not route wires and cables together with power or high voltage cables.

Otherwise the fieldbus system and/or I/O device can malfunction due to interference of noise and surge voltage

from power and high voltage cables to the signal line.

Route the wires (piping) of the fieldbus system and/or I/O device separately from power or high voltage cables.

•Confirm proper insulation of wiring.

Poor insulation (interference from another circuit, poor insulation between terminals, etc.) can lead to excess

voltage or current being applied to the product, causing damage.

•Take appropriate measures against noise, such as using a noise filter, when the fieldbus system is

incorporated into equipment.

Otherwise noise can cause malfunction.

Environment

•Select the proper type of protection according to the environment of operation.

If using in an environment that is exposed to water splashes, please take measures such as using a cover.

•Do not use in a place where the product could be splashed by oil or chemicals.

If the product is to be used in an environment containing oils or chemicals such as coolant or cleaning solvent, even

for a short time, it may be adversely affected (damage, malfunction etc.).

•Do not use the product in an environment where corrosive gases or fluids could be splashed.

Otherwise damage to the product and malfunction can result.

•Do not use in an area where surges are generated.

If there is equipment which generates a large amount of surge (solenoid type lifter, high frequency induction furnace,

motor, etc.) close to the fieldbus system, this may cause deterioration or breakage of the internal circuit of the

fieldbus system. Avoid sources of surge generation and crossed lines.

•When a surge-generating load such as a relay or solenoid is driven directly, use an fieldbus system with

a built-in surge absorbing element.

Direct drive of a load generating surge voltage can damage the fieldbus system.

•The product is CE marked, but not immune to lightning strikes. Take measures against lightning strikes

in the system.

•Prevent foreign matter such as remnant of wires from entering the fieldbus system to avoid failure and

malfunction.

-7-

No.EX※※-OMX1001

•Mount the product in a place that is not exposed to vibration or impact.

Otherwise failure or malfunction can result.

•Do not use the product in an environment that is exposed to temperature cycle.

Heat cycles other than ordinary changes in temperature can adversely affect the inside of the product.

•Do not expose the product to direct sunlight.

If using in a location directly exposed to sunlight, shade the product from the sunlight.

Otherwise failure or malfunction can result.

•Keep within the specified ambient temperature range.

Otherwise malfunction can result.

•Do not operate close to a heat source, or in a location exposed to radiant heat.

Otherwise malfunction can result.

Adjustment and Operation

•Perform settings suitable for the operating conditions.

Incorrect setting can cause operation failure.

•Please refer to the PLC manufacturer's manual etc. for details of programming and addresses.

For the PLC protocol and programming refer to the relevant manufacturer's documentation.

•The surface on the product may be hot.

Maintenance

•Turn off the power supply, stop the supplied air, exhaust the residual pressure and verify the release of

air before performing maintenance.

There is a risk of unexpected malfunction.

•Perform regular maintenance and inspections.

There is a risk of unexpected malfunction.

•After maintenance is complete, perform appropriate functional inspections.

Stop operation if the equipment does not function properly.

Otherwise safety is not assured due to an unexpected malfunction or incorrect operation.

•Do not use solvents such as benzene, thinner etc. to clean the each unit.

They could damage the surface of the body and erase the markings on the body.

Use a soft cloth to remove stains.

For heavy stains, use a cloth soaked with diluted neutral detergent and fully squeezed, then wipe up the stains

again with a dry cloth.

-8-

No.EX※※-OMX1001

Model Indication and How to Order

EX260-SEN 2 -X205

Output specification

32 outputs, NPN (positive common)/sink

Fieldbus

EtherNet/IPTM

-9-

No.EX※※-OMX1001

Summary of Product parts

No.

Element

Description

Fieldbus interface connector

(BUS OUT)

EtherNet/IPTM connection. (BUS OUT)

(RJ45 connector)

Fieldbus interface connector

(BUS IN)

EtherNet/IPTM connection. (BUS IN)

(RJ45 connector)

Power supply connector

Power supply with load voltage for valves and operating voltage for SI unit.

Output connector

Output signal interface for valve manifold.

LED display

LED display to indicate the status of the SI unit. 1

Mounting hole

Mounting hole for connection to the valve manifold.

Accessories

Hexagon socket head cap screw

2 pcs. M3 x 30 screw for connection to the valve manifold.

Seal cap

1 pc. seal cap for unused fieldbus interface connector (BUS OUT).

Power supply connector

1 pc. connector for power supply.

1: Refer to page 16 for the "LED Indication and Settings".

Table des matières

Autres manuels SMC Networks Unité de contrôle

SMC Networks

SMC Networks XGTP Series Manuel utilisateur

SMC Networks

SMC Networks VFR6000 Series Manuel utilisateur

SMC Networks

SMC Networks JSY5000-H Series Manuel utilisateur

SMC Networks

SMC Networks IL220-02 L Series Manuel utilisateur

SMC Networks

SMC Networks ASR Series Manuel utilisateur

SMC Networks

SMC Networks VHS20 Series Manuel utilisateur

SMC Networks

SMC Networks EX600-DX Series Manuel utilisateur

SMC Networks

SMC Networks ASP Series Manuel utilisateur

SMC Networks

SMC Networks VZ400 Series Manuel utilisateur

SMC Networks

SMC Networks VFS Series Manuel utilisateur

SMC Networks

SMC Networks VO317 Series Manuel utilisateur

SMC Networks

SMC Networks VQD1000 Series Manuel utilisateur

SMC Networks

SMC Networks VTA301 Series Manuel utilisateur

SMC Networks

SMC Networks EX260-SDN1 Mode d’emploi

SMC Networks

SMC Networks SX10 Series Manuel utilisateur

SMC Networks

SMC Networks VM100-A Series Manuel utilisateur

SMC Networks

SMC Networks VFR4000 Series Manuel utilisateur

SMC Networks

SMC Networks VEX5 Series Manuel utilisateur

SMC Networks

SMC Networks SY3000 SERIES Manuel d'installation

SMC Networks

SMC Networks XLA Series Manuel utilisateur

SMC Networks

SMC Networks VEX3 Series Manuel utilisateur

SMC Networks

SMC Networks VV100 Series Manuel

SMC Networks

SMC Networks VXP Series Manuel utilisateur

SMC Networks

SMC Networks SJ4000 Series Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur