SMART-AVI SM-DVN-2S Manuel utilisateur
TECHNICAL SPECIFICATIONS WHAT’S IN THE BOX
VIDEO
Fornat DVI Dual Link; DVI Single-Link; VGA
Host Interface (2) DVI-I 29-pin (female)
User Console
Interface (1) DVI-I 29-pin (female)
Max Resolution
DVI Dual-Link: 2560 x 1600;
DVI Single-Link: 1920 x 1200;
VGA: 1920 x 1080
DDC 5 volts p-p (TTL)
Input Equalization Automatic
Input Cable Length Up to 20 ft
Output Cable Length Up to 20 ft
USB
Signal Type USB 2.0, 1.1, and 1.0
w/ internal hub
Input Interface (2) USB Type B
Output Interface (2) USB 1.1 Type A for KVM Devices
(2) USB 2.0 Type A Transparent
AUDIO
Audio Input (2) 3.5mm stereo audio (female)
Audio Output (1) 3.5mm stereo audio (female)
POWER
Power Requirements 12V DC, 2A power adapter with
center-pin positive polarity
ENVIRONMENT
Operating Temp 32° to 104° F (0° to 40° C)
Storage Temp -4° to 140° F (-20° to 60° C)
Humidity 0-80% RH, non-condensing
CONTROL
Front Panel Push Buttons with LED indicators
RS-232 Via Serial @ 115200 bps
Hot Keys Via Keyboard
OTHER
Emulation Keyboard, Mouse and Video
PART NO. QTY DESCRIPTION
SM-DVN-2S 1 2-port, SH DVI-I KVM Switch
PS12VDC2A 112-VDC, 2-A power adapter with
center-pin positive polarity.
1Quick Start Guide
DESIGNED
AND MADE
IN THE USA
NOTICE
The information contained in this document
is subject to change without notice. iPGARD
makes no warranty of any kind with regard
to this material, including but not limited to,
implied warranties of merchantability and
tness for a particular purpose. iPGARD
will not be liable for errors contained
herein, or for incidental or consequential
damages in connection with the furnishing,
performance, or use of this material. No
part of this document may be photocopied,
reproduced, or translated into another
language without the prior written consent
from iPGARD, Inc.
20170518
Toll Free: (888)-994-7427
Phone: (702) 800-0005
Fax: (702)-441-5590
WWW.iPGARD.COM
A full manual can be downloaded from
www.ipgard.com/SM-DVN-2S/
SM-DVN-2S
Advanced KVM Switch
SINGLE-HEAD 2-PORT
DVI-I DUAL LINK KVM SWITCH
WITH USB 2.0 SHARING
Quick Start Guide
HARDWARE INSTALLATION
1. Ensure that power is turned off or disconnected from the unit and the computers.
2. Use DVI cables to connect the DVI output ports from each computer to the corresponding
DVI-I IN ports of the unit.
3. Use a USB cable (Type-A to Type-B) to connect a USB port on each computer to the
respective USB ports of the unit.
4. Optionally connect a stereo audio cable (3.5mm to 3.5mm) to connect the audio output of
the computers to the AUDIO IN ports of the unit.
5. Connect monitors to the DVI-I OUT console ports of the unit using DVI cables.
6. Connect a USB keyboard and mouse in the two USB console ports.
7. Optionally connect stereo speakers to the AUDIO OUT port of the unit.
8. Finally, power on the KVM by connecting a 12VDC power supply to the power connector, and
then turn on all the computers.
Note: You can connect up to 2 computers to the 2 port KVM.
DVI IN
DVI OUT
USB IN
USB K/M OUT
USB 2.0 OUT
AUDIO IN
AUDIO OUT
VGA SUPPORT
To use the SM-DVN with a VGA device, the monitor must also support analog signals. Once this
is afrmed, you can connect the VGA monitor and PC to the SM-DVN using passive VGA to DVI
adapters.
There are three ways to control
the KVM Switch: Keyboard HotKeys, RS-232
Serial Commands, and Front Panel Buttons.
The settings for the serial connection are as
follows: Baud rate: 115200; Data Bits: 8;
Parity: None; Stop Bits: 1; Flow Control: None.
The following commands can be used:
Users are able to customize the keys that
trigger Hotkeys. The following keys are
allowed: CT (Left/Right), Alt, Shift (Left/
Right), Caps Lock, Scroll Lock, F1-F12
Change HK Trigger
HK + HK + X + desired hotkey
View Current HK Trigger
Use the RS-232 command: //??<CR>
Default HotKey Trigger
CT (Left)
Chart Key
[CT] = Ctrl
<CR> = Carriage Return (Enter Key)
[HK] = Current Hot Key Trigger
Command Hotkey RS-232
Switch KVM [CT][CT][#]<CR> //m[#]<CR>
Audio Only [CT][CT]a[#]<CR> //a[#]<CR>
KM Only [CT][CT]c[#]<CR> //c[#]<CR>
USB Only [CT][CT]u[#]<CR> //u[#]<CR>
Learn EDID [CT][CT]e<CR> //e<CR>
Trigger Hotplug [CT][CT]h<CR> //h<CR>
Reset Software [CT][CT]r//r<CR>
Get Port Status N/A //??<CR>
SYSTEM CONTROL
CUSTOM HOTKEY TRIGGERS
Autres manuels SMART-AVI Changer
SMART-AVI
SMART-AVI DVN-8P Manuel utilisateur
SMART-AVI
SMART-AVI DV-SW16 Manuel utilisateur
SMART-AVI
SMART-AVI DPN-4DUO Manuel utilisateur
SMART-AVI
SMART-AVI SM-DVN-4Q Manuel utilisateur
SMART-AVI
SMART-AVI DVN-4QUAD-DL Manuel utilisateur
SMART-AVI
SMART-AVI SM-UHN-8S Manuel utilisateur
SMART-AVI
SMART-AVI HKM-04 Manuel utilisateur
SMART-AVI
SMART-AVI DVN-4P Manuel utilisateur
SMART-AVI
SMART-AVI QKVM4K Manuel utilisateur
SMART-AVI
SMART-AVI DVN-8Pro Manuel utilisateur
SMART-AVI
SMART-AVI SM-DVN-4Q Manuel utilisateur
SMART-AVI
SMART-AVI SM-DVN-4S Manuel utilisateur
SMART-AVI
SMART-AVI DV-SW2S Manuel utilisateur
SMART-AVI
SMART-AVI SM-DPN-4S Manuel utilisateur
SMART-AVI
SMART-AVI SM3-UHX-2D Manuel utilisateur
SMART-AVI
SMART-AVI HDN-8P Manuel utilisateur
SMART-AVI
SMART-AVI SM-DVN-82X Manuel utilisateur
SMART-AVI
SMART-AVI HDN-8P Manuel utilisateur
SMART-AVI
SMART-AVI SM-DVN-8S-S Manuel utilisateur
SMART-AVI
SMART-AVI DSK-2H Manuel utilisateur
