SMART-AVI SKM-04-LT Manuel utilisateur

SKM-04-LT

4-Port KM Switch with USB 2.0 Sharing

USER MANUAL

Designed and Manufactured in the USA

1-800-284-2131

www.smartavi.com

4-Port KM Switch with USB 2.0 Sharing 2

OVERVIEW

TECHNICAL SPECIFICATIONS_________________________________________________________________

WHAT’S IN THE BOX?_________________________________________________________________________

FRONT AND BACK___________________________________________________________________________

INSTALLATION_______________________________________________________________________________

INITIAL SETUP________________________________________________________________________________

SYSTEM OPERATION_________________________________________________________________________

TROUBLESHOOTING_________________________________________________________________________

TECHNICAL SUPPORT________________________________________________________________________

LIMITED WARRANTY STATEMENT____________________________________________________________

4-Port KM Switch with USB 2.0 Sharing 3

Technical Specifications

USB

Signal Type USB 2.0, 1.1, and 1.0 w/ internal hub

CPU Ports (4) USB Type B (female)

User Control Interface (2) USB Type-A for keyboard and mouse connecon only;

(2) USB Type-A for USB 2.0 transparent

AUDIO

Input Interface (4) 3.5 mm Stereo Audio

Output Interface (1) 3.5 mm Stereo Audio

CONTROL

Front Panel Buons

RS-232 Via Control @ 115200 bps

Hot Keys Via Keyboard

OSD PASS Technology and Mouse Gesture Switching

OTHER

Power Adapter External 100-240 VAC/5VDC3A @ 24W

Dimensions 12.57” W x 1.76” H x 6.69” D

Weight 4.2 lbs

Approvals UL, CE, ROHS Compliant

Operang Temperature +32 to +104°F (0 to +40°C)

Storage Temperature -4 to 140°F (-20 to +60°C)

Humidity 5 to 90% (No Condensaon)

Emulaon Keyboard and Mouse

4-Port KM Switch with USB 2.0 Sharing 4

What’s in the box?

FRONT AND BACK

PART NO. Q-TY DESCRIPTION

SKM-04-LT 1 4-Port KM Switch with USB 2.0 Sharing

PS5VDC3A 1 12VDC 3A (minimum) power adapter with center-pin posive polarity.

1 User Manual

SKM-04-LT Back

SKM-04-LT Front

4-Port KM Switch with USB 2.0 Sharing 5

INSTALLATION

1. Ensure that power is turned o or disconnected from the unit and the computers.

2. Use a USB cable (Type-A to Type-B) to connect a USB port on each computer to the respecve

USB ports of the unit.

3. Oponally connect a stereo audio cable (3.5mm to 3.5mm) to connect the audio output of the

computers to the AUDIO IN ports of the unit.

4. Connect a USB keyboard and mouse in the two USB console ports.

5. Oponally connect stereo speakers to the AUDIO OUT port of the unit.

6. Finally, power on the KM by connecng a 12VDC power supply to the power connector, and then

turn on all the computers.

Note: You can connect up to 4 computers to the 4 port KM.

VIDEO

USB IN

USB K/M OUT

USB 2.0 OUT

USB1 USB2 USB3 USB4 RS232

USB K/M

5VDC2A

SKM-04-LT

4-Port KM Switch with USB 2.0 Sharing 6

INITIAL SETUP

Absolute Mouse Mode KM Switching

Relative Mouse Mode KM Switching

Aer all devices are connected to the SKM-04-LT, the user must choose a display topology

conguraon and display mode. By default, the SKM-04-LT is congured to a topology with four

screens arranged horizontally starng with Port 1 on the le.

The installaon setup must match one of SKM-04-LT’s predened display topology conguraons.

This can be selected through keyboard hotkey commands. Please refer to the “Display Topology

Conguraon” secon for the available display topologies.

SmartAVI’s new PASS (Progressive Automac Screen Switching) technology allows seamless switching

between computers by moving the mouse cursor from one display to another. With PASS, users can

eortlessly switch computers for faster producvity. PASS only works in Absolute Mouse Mode.

When using computers with mulple displays, SmartAVI developed a new feature called Mouse

Gesture Switching, which is a technology that allows switching between computers using simple

mouse clicks and gestures. No device driver is required. Simply press the scroll wheel twice and then

move the mouse in the direcon of the channel you desire to switch to. This feature only works in

Relave Mouse Mode.

SOURCE 1

SOURCE 3

CURSOR CURSOR

AUTO-SWITCH FROM 4 TO 3

AUTO-SWITCH FROM 1 TO 2

AUTO-SWITCH

FROM 2 TO 4

AUTO-SWITCH

FROM 3 TO 1

SOURCE 2

SOURCE 4

SCROLL 2X THEN

TO THE RIGHT

SCREEN

TO THE LEFT

SCREEN

TO THE UPPER SCREEN

TO THE LOWER SCREEN

4-Port KM Switch with USB 2.0 Sharing 7

Note: Display Topology species the number of horizontal columns. The number of vercal rows is

calculated in the soware by 4/n columns.

Custom Hotkey Triggers

Users can customize the keys that trigger hotkeys. The default trigger for hotkey funcon on the

keyboard is Ctrl + Ctrl. The trigger funcon can be used to change to the following keys:

Ctrl (Le / Right), Alt, Shi (Le / Right), Caps Lock, Scroll Lock, F1-F12

To view the current hotkey trigger seng:

Use the RS-232 command: /+ /+ ?+ ?+ Enter to view the current hotkey trigger. To reset the Hotkey

Trigger, use the “Factory Defaults” command.

To change the hotkey trigger seng:

[hotkey] + [hotkey] + X+ [desired hotkey]

Example: If the user’s current hotkey trigger is Shi and they want to change it to Scroll Lock, the user

would type Shi + Shi + X+ Scroll Lock.

COMMANDS HOTKEY

Display Topology (mulple rows) [CTRL][CTRL] H [1-4]

Limit Input Ports (one row only) [CTRL][CTRL] W[1-4]

Cursor Rolling (roll past display borders

up, down, le, and right) [CTRL][CTRL] O[0(OFF), 1(ON)]

# STATUS DESCRIPTION

1 OFF Non-selected port

2 ON Selected port

System operation

There are four ways to control the SKM-04-LT: front panel buons, keyboard hotkeys, RS-232 serial

commands, and through the included graphical user interface (GUI).

Front Panel Control

To switch to an input port, simply push the buon on the front-panel of the KM. If an input port is

selected, the LED of that port will turn on.

Front Panel - Port Selecon LEDs:

Hotkey Commands

A Hotkey command is a keyboard sequence used to trigger an acon on the SKM-04-LT via the

keyboard connected to the USB port of the SKM-04-LT. To acvate the hotkey sequence, press the

CTRL key twice and then enter the desired hotkey commands.

Note: All commands can use upper and/or lower case characters.

4-Port KM Switch with USB 2.0 Sharing 8

System operation (continued)

RS-232 Serial Control

The SKM-04-LT may also be controlled via RS-232 commands. To use these commands, you must use

HyperTerminal or an alternate terminal applicaon. The sengs for the connecon are as follows:

Baudrate 115200; Data Bits 8; Parity None; Stop Bits 1; Flow Control None.

Once you have connected to the SKM-04-LT via Serial, you will see the SKM-04-LT informaon when

the device starts up.

The following commands can be used for RS-232 with available keyboard hotkeys:

Graphical User Interfaces

In addion to the front panel buons, keyboard hotkeys, and RS-232 serial commands described

above, the SKM-04-LT can be congured through a simple GUI that oers all the same customizaon

opons as the other control methods. This interface can be accessed on the connected computers.

COMMAND DESCRIPTION HOTKEY RS-232 COMMAND

Switch All USB [CTRL][CTRL] [port #] [ENTER] //m[port #] [ENTER]

Switch KM Only [CTRL][CTRL] c[port #] [ENTER] //c[port #] [ENTER]

Switch USB Only [CTRL][CTRL] u[port #] [ENTER] //u[port #] [ENTER]

Reset Soware [CTRL][CTRL] r [ENTER] //r[ENTER]

Factory Defaults [CTRL][CTRL] f [ENTER] //f[ENTER]

Get Port Status N/A //?? [ENTER]

Switch resoluon

SKM channel: 1-4

Resoluon:

1 (1080p), 2 (4K), 3 (2K), 4 (720p)

[CTRL][CTRL] ce [SPACE] [SKM #]

[SPACE] [RESOLUTION #]

//ce [SPACE] [SKM #]

[SPACE] [RESOLUTION #]

Mouse control

X and Y axes set in percents

[CTRL][CTRL] mm [SPACE]

[resolution #] [SPACE] [x #]

[y #]

//mm [SPACE]

[resolution #] [SPACE]

[x #] [y #]

Mouse default posion [CTRL][CTRL] rl [ENTER] //rl [ENTER]

4-Port KM Switch with USB 2.0 Sharing 9

System operation (continued)

Display Topology Conguraon

The SKM-04-LT has a congurable display topology conguraon that can be easily acvated through

keyboard hotkeys. No soware or drivers are required to congure the display topology.

Note: Hotkey CTRL +CTRL command allows for mulple rows.

(1) Hotkey Command: “CTRL +CTRL +H +4 +ENTER”

Limit Input Ports Conguraon

The SKM-04-LT allows the user to shut o input from specic connected computers without the need

to disconnect them from the switch.

Note: Limit Input Ports commands reset the Display Topology conguraon.

Hotkey Commands: CTRL, CTRL W(X) commands (allows one row only):

CTRL +CTRL +W +4 +ENTER

Note: Limit Input Ports commands reset Display Topology conguraon.

CTRL +CTRL +W +3 +ENTER

Note: Port 4 N/A

Note: Port 3, 4 N/A

Note: Port 2-4 N/A

CTRL +CTRL +W +2 +ENTER

CTRL +CTRL +W +1 +ENTER

(2) Hotkey Command: “CTRL +CTRL +H +2 +ENTER”

(3) Hotkey Command: “CTRL +CTRL +H +3 +ENTER”

(4) Hotkey Command: “CTRL +CTRL +H +1 +ENTER”

1 2 3 4

1 2

3 4

1 2 3

1 2

4-Port KM Switch with USB 2.0 Sharing 10

Resoluon and Mouse Conguraon

System operation (continued)

//CE [SPACE] [SKM #] [SPACE] [resoluon #]

Where SKM channel can be set 1-4

Where Resoluon number is the following:

1. 1080p

2. 4K

3. 2K

4. 720p

For example: //CE 1 2

In this example we are seng channel 1 to reference 4K resoluon.

//MM [SPACE] [resoluon #] [SPACE] [x integer # (1-100)] [y integer # (1-100)]

For example: //MM 2 80 50

In this example we are seng the mouse movement according to 4K resoluon with 80 as the mouse

speed mulitplier for X and 50 as the mouse speed mulplier for Y.

The integer number set for the mouse mulplier will act as a value from 1-100%.

In the example above we are using the following:

80 for X, therefore 80 will become 80% of the mouse movement moving horizontally on the X-axis

50 for Y, therefore 50 will become 50% of the mouse movement moving vercally on the Y-axis

100 will do 100%, 65 will do 65%, 5 will do 5%, etc.

Suppose you move the mouse 100 units for the X axis and 10 units for the Y axis. The soware will

change 100 * 80% = 80 units for the X axis and 10 * 50% = 5 unit for the Y axis. This will cause the

mouse cursor to move slower.

//RL will return the channel’s current mouse mulitplier percentage and the current resoluon which will

reference the resoluon number menoned in the // C E command.

COMMAND DESCRIPTION RS-232 COMMAND

Switch resoluon //ce [SPACE] [SKM #] [SPACE] [resolution #] [ENTER]

Mouse control //mm [SPACE] [resolution #] [SPACE] [x #] [y #] [ENTER]

Mouse default posion //rl [ENTER]

Autres manuels pour SKM-04-LT

Table des matières

Autres manuels SMART-AVI Changer

SMART-AVI

SMART-AVI SM-UHN-8S Manuel utilisateur

SMART-AVI

SMART-AVI SM-KMN-08 Manuel utilisateur

SMART-AVI

SMART-AVI DPN-2P Manuel utilisateur

SMART-AVI

SMART-AVI SM-D2H-4S Manuel utilisateur

SMART-AVI

SMART-AVI SM-DVN-4S Manuel utilisateur

SMART-AVI

SMART-AVI DPN-4QUAD Manuel utilisateur

SMART-AVI

SMART-AVI DVN-4PRO Manuel utilisateur

SMART-AVI

SMART-AVI DVN-4PRO Manuel utilisateur

SMART-AVI

SMART-AVI SM-UHN-4S Manuel utilisateur

SMART-AVI

SMART-AVI HKM-02 Manuel utilisateur

SMART-AVI

SMART-AVI RDU-8P Manuel utilisateur

SMART-AVI

SMART-AVI UHDN-4P Duo Manuel utilisateur

SMART-AVI

SMART-AVI DVN-4DUO Manuel utilisateur

SMART-AVI

SMART-AVI DPN-4DUO Manuel utilisateur

SMART-AVI

SMART-AVI DV-SW4S Manuel utilisateur

SMART-AVI

SMART-AVI UHD-2DUO Manuel utilisateur

SMART-AVI

SMART-AVI HKM-04 Manuel utilisateur

SMART-AVI

SMART-AVI QKVM4K Manuel utilisateur

SMART-AVI

SMART-AVI DPN-4 Duo Manuel utilisateur

SMART-AVI

SMART-AVI DVN-16Pro Manuel utilisateur

SMART-AVI

SMART-AVI DVNET-4Duo-DL Manuel utilisateur

SMART-AVI

SMART-AVI HDR-4X4-PLUS-V2 Manuel utilisateur

SMART-AVI

SMART-AVI SM-DVN-16S Manuel utilisateur

SMART-AVI

SMART-AVI DPN-4 Quad Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur