Smacq Technologies USB-5100 Series Manuel utilisateur

USB-5100 Series Multifunctional

Data Acquisition Devices

User Manual

Rev. C

Beijing Smacq Technology Co., Ltd.

Smacq.com

Smacq.cn

竺

macq.

Smacq

1 |

Statement

No content of this manual may be reproduced, modified or abridged without prior consent and

written permission.

Trademark information

Smacq is a registered trademark of Beijing Smacq Technology Co., Ltd

The names of the other products and companies mentioned in this document are trademarks

or trade names of their respective companies.

Other Disclaimer

The information provided in this document may be modified and updated in

subsequent versions without prior notice.

Smacq does not provide any warranties, express or implied, for this document as

well as the information inside it, including but not limited to implied warranties of

the marketable nature of the product and its suitability for a particular purpose.

There may be a chance that inaccurate descriptions or errors exist in this document.

Smacq does not hold any liability for accidents because of the information and

deductive functions provided in this manual, as well as the resulting loss of any

chance because of the use of this document.

Smacq reserves the rights to change product specifications, prices, and decide

whether to stop the production.

If you have any questions or need assistance in using this product or this

document, please contact us via:

Phone:(+86)10-52482802

E-Mail:[email protected]

Website:http://www.smacq.com

http://www.smacq.cn

Smacq

2 |

Safety Requirements

Warning

Only the voltage within the specified range can be connected.

Voltage exceeding the specified range may cause damage to the

device, and even present a negative impact on personal safety.

Check the product specification for detailed reference to the range

of voltages that can be connected by each port.

Do not attempt to operate the device in other ways that are not

mentioned in this document. Incorrect use of the device may be

dangerous. In the event of device damage, the internal security

protection mechanism will also be affected.

Do not attempt to replace device components or change devices

in other ways that are not mentioned in this document. Do

not repair the device yourself in the event of a product failure.

Do not use the device in an environment where an explosion may

occur or where flammable flue or gas is present. If you must use

the device in this kind of environment, please fit it into a proper

case.

While the device is running, all chassis covers and fill panels need

to be closed.

For equipment with exhaust vents, do not insert foreign objects

into the vents or block air circulation in the vents.

心

心)

心〉

心)

心

重立五工江温

3 |

Measurement Categories

Warning For use in measurement category I (CAT I) only. Do not use in

measurement category II/III/IV. Use this device to connect

signals or make measurements.

Measurement categories Note

Measurement categories I (CAT I) means that measurements are made on a circuit that

is not directly connected to the main power supply. For example, a circuit that is not

exported from the main power supply, especially a circuit that is exported from a

protected (internal) primary power supply, is measured. In the latter case, the

instantaneous stress will change. Therefore, the user should be aware of the

instantaneous affordability of the device.

Measurement categories II (CAT II) means that measurements are made on a circuit

that is directly connected to a low-voltage device. For example, a measurement on

household appliances, portable tools and similar equipment.

Measurement categories III (CAT III) means that measurements are made in

construction equipment. For example, a measurement on the distribution boards, circuit

breakers, wiring (including cables, Busbars, junction boxes, switches, sockets) in fixed

equipment and equipment for industrial use and certain other equipment (for example,

fixed motors that are permanently connected to fixtures).

Measurement categories IV (CAT IV) means that measurements are made on the source

of low-voltage equipment. For example, a measurement on a meter, a major

overcurrent protection device, and a pulse control unit.

Environment

Temperature

Operating 0℃ ~ 55℃

Storage -40℃ ~ 85℃

心)

竺

ma,cq.

4 |

Recycle precautions

Warning Some of the substances contained in this product may be

harmful to the environment or human health. In order to

avoid releasing harmful substances into the environment or

endangering human health, it is recommended that appropriate

methods be used to recover this product to ensure that most

materials can be properly reused or recycled. For information

about processing or recycling, please contact your local

professional organizations.

Humidity

Operating 5%RH ~ 95%RH, no condensation

Storage 5%RH ~ 95%RH, no condensation

Pollution degree 2

Highest elevation 2000 m

Pollution degree description

Pollution degree 1:No pollution, or only dry non-conductive pollution. This pollution

degree has no effect. For example: a clean room or an air-conditioned office

environment.

Pollution degree 2:Generally only dry non-conductive pollution occurs. Temporary

conduction can sometimes occur due to condensation. For example:General indoor

environment.

Pollution degree 3:Conductive pollution occurs, or dry non-conductive pollution

becomes conductive due to condensation. For example, an outdoor sheltered

environment.

Pollution degree 4:Permanent conductive pollution caused by conductive dust, rain, or

snow. For example:Outdoor places.

心)

竺

ma,cq.

5 |

CONTENT

STATEMENT................................................................................................................1

SAFETY REQUIREMENTS............................................................................................2

MEASUREMENT CATEGORIES.................................................................................... 3

ENVIRONMENT.......................................................................................................... 3

1.GETTING STARTED............................................................................................ 7

1.1. PRODUCT INTRODUCTION.................................................................................. 7

1.2. FUNCTION DIAGRAM.......................................................................................... 8

1.3. PRODUCT SPECIFICATIONS................................................................................. 8

1.4. PRODUCT UNPACKING....................................................................................... 12

PRECAUTIONS.......................................................................................................... 12

CHECK THE PACKING LIST........................................................................................ 12

2. INSTALLATION..................................................................................................13

2.1. CONNECTOR SIGNAL PINS DISTRIBUTION......................................................... 13

2.2. USB CABLE REINFORCEMENT DESIGN................................................................ 14

2.3. DRIVER INSTALLATION..................................................................................... 15

3. ANALOG INPUT (AI)...........................................................................................16

3.1. CIRCUIT DIAGRAM............................................................................................ 17

3.2. SIGNAL CONNECTION METHODS....................................................................... 17

3.3. SIGNAL ACQUISITION MODE............................................................................. 17

HARDWARE TIMING MODE....................................................................................... 17

CONTINUOUS ACQUISITION MODE.......................................................................... 17

LIMITED NUMBER ACQUISITION MODE ....................................................................18

3.4. AI SAMPLING CLOCK..........................................................................................18

3.5. TRIGGER..........................................................................................................19

CLEAR TRIGGER...................................................................................................... 20

PRE-TRIGGER..........................................................................................................20

4. ANALOG OUTPUT (AO)......................................................................................21

4.1. CIRCUIT DIAGRAM...........................................................................................21

4.2. SIGNAL OUTPUT MODE.....................................................................................21

DC IMMEDIATE OUTPUT........... ...............................................................................21

HARDWARE TIMING.................................................................................................21

FINITE NUMBER OUTPUT MODE ..............................................................................22

INFINITE LOOP OUTPUT MODE ............................................................................... 22

INFINITE NON-LOOP OUTPUT MODE........................................................................22

4.3. OUTPUT UPDATE RATE......................................................................................22

SYNCHRONOUS UPDATE...........................................................................................22

4.4. AO SAMPLING CLOCK........................................................................................23

4.5. TRIGGER..........................................................................................................23

CLEAR TRIGGER.......................................................................................................24

詈，

｀立竺

6 |

5. DIGITAL INPUT (DI)..........................................................................................25

5.1. SIGNAL ACQUISITION MODE............................................................................. 25

HARDWARE TIMING..................................................................................................25

CONTINUOUS ACQUISITION MODE........................................................................... 25

LIMITED NUMBER ACQUISITION MODE .................................................................... 25

5.2. SAMPLING RATE............................................................................................... 26

5.3. DI SAMPLING CLOCK......................................................................................... 26

5.4. TRIGGER.......................................................................................................... 26

CLEAR TRIGGER ...................................................................................................... 27

PRE-TRIGGER.......................................................................................................... 27

6.DIGITAL OUTPUT (DO)...................................................................................... 29

6.1. SIGNAL OUTPUT MODE..................................................................................... 29

IMMEDIATE OUTPUT................................................................................................ 29

HARDWARE TIMING ................................................................................................ 29

FINITE NUMBER OUTPUT MODE ...............................................................................29

INFINITE LOOP OUTPUT MODE................................................................................ 30

INFINITE NON-LOOP OUTPUT MODE........................................................................ 30

6.2. OUTPUT UPDATE RATE..................................................................................... 30

6.3. DO SAMPLING CLOCK....................................................................................... 30

6.4. TRIGGER.......................................................................................................... 31

CLEAR TRIGGER.......................................................................................................32

7.SYNCHRONIZATION SYSTEM........................................................................... 33

7.1. SAMPLING CLOCK ............................................................................................33

7.2. EXTERNAL TRIGGER..........................................................................................34

8.SERVICE AND WARRANTY................................................................................ 36

9.ORDERING INFORMATION............................................................................... 37

詈，

｀立竺

7 |

1. Getting Started

This chapter describes the basic functions of USB-5100 Series Data Acquisition Device,

as well as product specifications and precautions in the process of product unpacking.

1.1.Product introduction

USB-5100 Series data acquisition device is the multifunctional data acquisition device

based on high-speed USB2.0 interface. When connected to the computer, it can be

used for continuous high-speed signal acquisition and high-speed control signal output.

USB-5100 series of data acquisition devices can measure analog and digital

signals continuously and save the data to the computer hard drive without interruption.

It can also provide digital signal output, periodic repetitive signal output, and

high-speed uninterrupted non-repetitive signal output controlled by a computer.

USB-5100 series data acquisition device supports operating in Windows OS,

providing standard DLLs and support for mainstream development languages including

VC++, VB, C#, LabVIEW, and MATLAB.

USB-5100 series data acquisition device provides multiple models, in terms of function

and performance. For detailed reference, please turn to Chapter 1.3 for

specification description of each model.

Key Features

High speed USB interface, Plug and Play, USB powered

16-bit analog input resolution, support continuous uninterrupted

acquisition

The analog input supports up to 16 channels of synchronous sampling and

up to 500kS/s/Ch sampling rate.

16-bit analog output resolution, with output range of ±10V

Support 4 channel synchronous analog output, up to 100kS/s sampling

rate

Support continuous analog output of nonrepetitive arbitrary waveforms of

infinite length

Up to 10MS/s/Ch sampling rate for digital I/O

竺

ma,cq.

8 |

1.2. Function Diagram

Digital system

USB bus

Trigger source:

Software trigger

External trigger

Din trigger

Sampling clock source:

Internal module

sampling clock source

External sampling

clock source

Digital I/O

FIFI cache

Figure 1.1 USB-5100 series data acquisition device functions

1.3. Product specifications

The following product specification parameters, unless otherwise stated, are acquired

at the temperature of 25°C and the humidity of 40%, while the device is turned on for

20 minutes.

Analog input

Number of channels

USB-5120/5121: 16Single-Ended

USB-5110/5111: 8Single-Ended

USB-5520/5521: 16Single-Ended

USB-5510/5511: 8Single-Ended

USB-5320/5321: 16Single-Ended

USB-5310/5311: 8Single-Ended

ADC type SAR

Resolution USB-5120/5121/5110/5111: 16-bit

5macq.

Figure 1.1 shows the schematic diagram of USB-5100 series data acquisition device

9 |

USB-5520/5521/5510/5511: 14-bit

USB-5320/5321/5310/5311: 12-bit

Highest sampling rate

USB-5111/5121: 500kS/s/Ch,continuous

USB-5110/5120: 250kS/s/Ch,continuous

USB-5511/5521: 500kS/s/Ch,continuous

USB-5510/5520: 250kS/s/Ch,continuous

USB-5311/5321: 500kS/s/Ch,continuous

USB-5310/5320: 250kS/s/Ch,continuous

Timing resolution 10 ns

Channel synchronization Yes

Range ±10 V / ±5V

Input coupling mode DC

Input impedance 100 MΩ

Small signal bandwidth

（-3 dB）

Input bias current 1uA

Analog input max voltage ±15V

Software FIFO 2 MPts/Ch

Pre-trigger FIFO 4096 Pts

AI capture mode Continuous acquisition mode and limited number acquisition mode

Analog input accuracy (with temperature coefficient of 5 ppm/℃)

Range Gain error

(ppm of reading

Offset error

(ppm of range)

Random noise

（μVrms）

Full range absolute

accuracy （μV）

±10 V 90 4 180 1100

±5 V 80 10 90 500

Analog output

Number of channels 4

Resolution 16-bit

DNL ±1 LSB

Highest update rate 100 kHz/Ch

Timing resolution 10 ns

Channel synchronization Yes

Input range ±10 V

Output coupling DC

Output impedance 0.1 Ω

Output drive current 10 mA

竺

ma,cq.

450 kHz

Resolution

Table des matières

Autres manuels Smacq Technologies Matériel informatique

Smacq Technologies

Smacq Technologies PCI-3000 Series Manuel utilisateur

Smacq Technologies

Smacq Technologies USB-3300 Series Manuel utilisateur

Smacq Technologies

Smacq Technologies PCI-1232 Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur