Slendertone System+ Manuel utilisateur

All manuals and user guides at all-guides.com

all-guides.com

Congratulations on purchasing your SLEN ERTONE SYSTEM+. Please read your

user manual fully before using this product.

This revolutionary new concept allows a single hand-held controller to be

attached to a range of garments which tone different areas of the body,

saving you money on your next SLEN ERTONE purchase. SLEN ERTONE SYSTEM+

uses clinically proven EMS technology to exercise all of the muscles of

your abdomen, not just those under the belt. A signal is sent to the

abdominal muscles and as the signal strength increases, the muscles

contract.

Use your SLEN ERTONE SYSTEM+ 5 times a week and in just 4 weeks, you can

expect to see these results:

• A firmer, flatter stomach

• Stronger more toned abs

• Better fitting clothes

For best results we recommend that you use your SLEN ERTONE SYSTEM+ in

conjunction with a normal, healthy diet and exercise.

SLEN ERTONE SYSTEM is an electronic muscle stimulator intended for the

enhancement of performance of normal muscle. It may also be used, with

medical supervision, for the rehabilitation of muscle which has become

deficient due to disuse or injury.

If you have any difficulty setting up your unit or have any other questions

or concerns about your SLEN ERTONE SYSTEM+ call the SLEN ERTONE Careline

on :

UK: 0845 070 7777 Email: info@slendertone.com

Rep. of Ireland: 1890 9223388 slendertone.com/system

International: +353 1 844 1016

Should your SLEN ERTONE SYSTEM+ unit develop a fault within two years of pur-

chase, SLEN ERTONE will undertake to replace or repair the unit or any parts

found to be defective with no charge for labour or materials *, provided the

unit:

• Has been used for its intended purpose and in the manner described in this

user manual.

• Has not been connected to an unsuitable power source.

• Has not been subjected to misuse or neglect.

• Has not been modified or repaired by anyone other than an approved

SLEN ERTONE agent.

This guarantee complements existing national guarantee obligations and does

not affect your statutory rights as a consumer.

* This excludes consumables (e.g. pads, belt, etc.) which are subject to normal wear

and tear.

welcome

product warranty

All manuals and user guides at all-guides.com

These are the contents for the full SLEN ERTONE SYSTEM+ pack. The Accessory

Pack does not contain a unit or charger.

1. Belt:

Your belt has been ergonomically designed and is fastened around your

waist, under you clothes, during use. The female belt (E :70) fits waist sizes

24”-44”/ 61-112cm. The male belt (X :70) fits waist sizes 27”-47”/ 69-119cm.

The belt has a pocket for holding your unit during use.

2. Unit:

The unit generates signals which are sent, via the belt and pads, to your muscles

to make them contract. Your unit is rechargeable and takes approximately 3

hours to charge fully.

2a. Unit Connector:

This connects the unit to the toning belt. Make sure the unit is fully connected

to the belt.

IMPORTANT:o not disconnect the unit from the toning belt until it has been

switched off.

3. Pack of three adhesive pads.

These adhesive pads are placed onto your belt before use. When you wrap

the belt around your waist, these pads must be in contact with your skin so

that signals can be sent to your muscles.

4. SLEN ERTONE Battery Charger:

Plug the charger into a socket and then connect your unit to the charger to

charge your unit’s battery. Please ensure you only use the charger supplied

by Slendertone

5. Instruction Literature:

This is a detailed guide to using your SLEN ERTONE SYSTEM+ and an additional

quick start guide to help get you started.

introducing your SLENDERTONE SYSTEM+

English

All manuals and user guides at all-guides.com

1. On/Off Button ( )

Press and hold this button for 2 seconds

to turn your unit on or off. You may also

pause the exercise by briefly pressing this

button.

2. Increase Toning Intensity ( )

Press and hold these buttons to increase

the intensity of the exercise. The right-

hand button controls the right-hand side

of your belt. The left-hand button controls

the left-hand side.

3. ecrease Toning Intensity ( )

Press and hold these buttons to decrease the

intensity of the exercise on either side of the belt.

(i) To increase or decrease intensity quicker

hold both intensity up/down buttons and the ( i ) but-

ton simultaniously.

4. Programme Button ( P )

Press this button to select the toning programme you wish to use. There are

10 programmes in total, which are explained later in this manual (page 8).

5. Information Button ( i )

Press this button to see your training information, such as the maximum

intensity for your current or last session and the number of sessions you

have completed.

Toning intensity from the left-hand side of the belt.

Toning intensity from the right-hand side of the belt.

Counts down the time left in the current session. Also displays error

messages (see page 10).

Appears when the exercise has been paused.

Indicates that the sound is off.

Keylock is active - you cannot change the intensity levels or the

program accidentally.

This symbol indicates a poor contact between the unit and the belt

or between the pads and the skin (see page 14 for more details).

Shows the battery power remaining.

Number of sessions completed.

Shows the programme currently running (1 - 10).

This symbol appears during each contraction phase.

Maximum intensity for the current/ last session.

unit display

unit controls

unit display

All manuals and user guides at all-guides.com

Step 1 -Charge the battery. Insert your charger into a

socket and then connect it to your unit (Fig. a). It’ll take

approximately 3 hours to fully charge the battery. Your

unit is fully charged when all three sections of the battery

icon are full. The battery icon will flash when the battery

is low and needs to be recharged.

NOTE:Please ensure you only use the SLEN ERTONE SYSTEM

Charger when charging your control unit. o not leave

your unit connected to the charger when the battery is

fully charged.

Step 2 -Connect the unit to the belt. The unit and belt

must be connected for your SLEN ERTONE SYSTEM+ to work.

‘Click’ the unit connector into the belt connector

as shown in Fig. b.

Step 3 -Place the pads on the belt. Turn the belt over so

that the 3 silver studs are facing upwards. Remove the

three adhesive pads from their pack. There is 1 large

square pad and 2 smaller oval pads. One side of each

pad has a grid pattern on it while the other side is plain

black.

(i) Remove the covers from the patterned side of the

large pad (Fig. c).

(ii) Place the patterned side of this pad over the middle

stud and between the white lines.

(iii) Now remove the covers from the patterned side of the two smaller pads

and place them either side of the large pad (Fig. d).

setting up your slendertone system+

Fig. a

Fig. b

English

Fig. c

Fig. d

SLEN ERTONE SYSTEM+ uses electrical muscle stimulation (EMS) technology.

This technology has been used in hospitals and by physiotherapists for over

50 years. Here is a summary of how EMS technology works. SLEN ERTONE‘s

patented 3-pad design ensures that all of the abdominal muscles contract

and not only those directly under the pads.

Step 1

Signals are sent

between the pads

Step 2

The signals switch on the

nerves which control the

abdominal muscles.

Step 3

The nerves, in turn, cause

your muscles to contract

and relax rhythmically.

how does muscle stimulation technology work?

All manuals and user guides at all-guides.com

(iv) The location of the smaller pads depends on your waist size. In the exam-

ple below, the smaller pads are placed nearest to the large, central pad. This

is for a user who’s waist size is 24”-31” (female)/ 27”-34” (male). Use the

sizing guidelines below to help you choose your correct pad location.

IMPORTANT:

Before you progress, make sure that all three silver studs are completely

covered by the pads.

Press the edges of all three pads firmly onto the belt before use.

Step 4 -Remove the covers from the black side of all

three pads (Fig. a). o not throw these covers away as

you will need to put them back onto the pads at the

end of your session.

NOTE:You should only use SLEN ERTONE pads with your

SLEN ERTONE SYSTEM+ unit.

Step 5 -Position the belt on your body.

Wrap the belt around your waist so that the pads are

pressed firmly against your skin, positioning the

large square pad over your navel (belly button).

Stretch the ends of the belt around your waist until

the small pads are between your hip bone and ribs

on either side of your body (Fig. b). Fasten the belt

tightly around your waist, but not so tight as to

cause discomfort. The pads are water-based, so you

may find they are cool when placed on your skin.

NOTE:For the best results, we recommend that you do five training sessions

per week. You should, however, only do one session per day, as this allows

your muscles to recuperate. Use your SLEN ERTONE SYSTEM+ whenever it suits

you. You can use your SLEN ERTONE SYSTEM+ almost any time and any place.

You can use it at home watching television, working at a desk, in the garden

or even walking outdoors. Your SLEN ERTONE SYSTEM+ really is a convenient

way of toning your abs.

Fig. a

Fig. b

For waist sizes 24”-31” / 61-79cm

For waist sizes 30”-38” / 76-97cm

For waist sizes 37”-44” / 94-112cm

For waist sizes 40”-47”/ 102-119cm

For waist sizes 33”-41”/ 84-104cm

For waist sizes 27”-34” / 69-86cm

MALE BELT SIZES

FEMALE BELT SIZES

All manuals and user guides at all-guides.com

all-guides.com

Muscle toning can be an unusual sensation, but a pleasant one. It may

tickle to begin with. We recommend that you use the product while seated

until you become accustomed to the sensation. This progresses to a smooth

muscle contraction as the toning intensity increases. To get started, follow

these simple steps:

Step 1: Press and hold the on/off button ( - Fig. a))

for two seconds to switch your unit on.

Step 2: Select the program you wish to use by pressing

the program button ( P- Fig. b). Then, to start the

program, press and hold the increase intensity buttons

( - Fig. c) until you feel your muscles contracting.

Always choose an intensity level at which you feel a

strong but comfortable contraction. This will vary from

person to person. You should try to reach an intensity

level of 15 or higher in your first session. The increasing

intensity level is displayed on the screen.

Step 3: Continue increasing the intensity throughout

the session if possible. You will feel the muscle

contractions getting stronger as the intensity increases.

Remember the harder you work your muscles the better

the results you will see, but always reduce the intensity

if you feel any discomfort. Your unit’s intensity range

is 0-150.

PAUSING A SESSION

If you wish to pause a session before it is finished, simply press the on/off

button briefly. The display will show that the unit is paused ( ). To resume

the session, briefly press the on/off button again. The display will return to

its normal mode.

Step 4: SESSION OVER

At the end of the training session your SLEN ERTONE SYSTEM+ will stop auto-

matically. However, to switch off your unit at any time during a session,

press and hold the on/off button for two seconds. You should see the display

turn off.

Step 5: Remove the belt and put the covers back on the black side of the

pads. Store it in the pouch until your next session.

NOTE:o not disconnect the unit from the belt without first switching the unit

off, as this may result in an error on your display.

Well done on completing your first training session!

your irst toning session

Fig. a

Fig. b

Fig. c

English

All manuals and user guides at all-guides.com

1. Use the strongest training intensity you can - the harder you work your

muscles, the better the results you will see, but remember, stimulation

should never be uncomfortable.

2. Use your SLEN ERTONE SYSTEM+ as part of a normal, healthy lifestyle.

Improve your diet and try to increase the amount of exercise you do. Your

toning belt will not help you lose weight. For this you need to do some form

of cardiovascular exercise e.g. walking, cycling, swimming, jogging.

However using your toning belt regularly will give you firmer, flatter abs, a

better body shape and your clothes will fit better.

3. Your SLEN ERTONE SYSTEM+ has 10 toning programmes which are listed in the

table below. There are 5 core programmes and 2 bonus programmes.

Programme 1 is set when you switch your unit on for the first time. The unit

will then automatically progress through each programme up to programme 5.

Programmes 6 and 7 must be selected manually using the program button.

The display will show the programme currently selected.

NOTE:All micro-coulomb (µC) values are rounded off to the nearest integer

value. This measures the effectiveness of the muscle workout - the higher

the µC value, the more effective the muscle workout.

All programmes have “warm up” and “warm down” phases. The warm-up

prepares your muscles for the main part of your session. The warm down

relaxes your muscles as the session is finishing - as you would when

exercising.

NOTE:You cannot change a programme during a session. You must first switch

your unit off and then on again. Then you can select a different programme

by pressing the programme button. Programme 6 delivers a strong abdominal

workout, which is useful for those involved in sport. Programme 7 is lower in

intensity and is useful when you require a less vigorous abdominal muscle

workout.

Programme

Name

Beginner

Intermediate

Advanced

Expert

Pro (i)

Pro (ii)

Ab-Power

Endurance

Programme

Name

Crunch (i)

Crunch (ii)

Session

uration

20:00

25:00

30:00

40:00

Session

uration

06:00

09:00

Training

Level

light

moderate

Strong

Light

Training

Level

moderate

Toning

Power

14µC

16µC

18µC

19µC

21µC

22µC

14µC

Toning

Power

16µC

Auto

Progression

2 sessions

3 sessions

5 sessions

10 sessions

Indefinite

Auto

Progression

Simultaneous

Alternate channels

getting results with your slendertone system+

core programs

bonus programmes

All manuals and user guides at all-guides.com

4. To help you get the most from your SLEN ERTONE SYSTEM+, we recommend that

you follow our 30 day plan. To follow this plan, use your belt 5 times a week

for 4 weeks and record your highest intensity levels in your diary (page 17).

Each week you have two rest days to allow your muscles to recover. The

diary below shows one person’s toning intensity, recorded during scientific

testing over a 30-day period.

NOTE:The intensity level will vary from person to person.

We recommend that you follow a similar plan, trying to push yourself to use

higher toning intensity levels all the time. Try to increase your toning intensi-

ty from week to week. But remember, do not over-exert yourself when using

muscle stimulation. Any workout should be at a level comfortable for you.

Week ay 1 ay 2 ay 3 ay 4 ay 5 ay 6 ay 7

1 (40 40) rest (40 40) rest (70 70) (70 70) (70 70)

2 rest (70 70) (80 80) rest (80 80) (80 80) (80 80)

3 rest (85 85) (85 85) rest (85 85) (90 90) (150 150)

4 rest (90 90) (90 90) rest (90 90) (90 90) (150 150)

Each box shows the average toning intensity from either side of the belt.

Fill-in your diary every time you complete a toning session. Leave this diary

somewhere you will see it regularly. This will help to motivate you to reach

your goal. You will soon see and feel that your ab muscles are firmer and

more toned.

Your belt can be washed, but you must first remove the unit and pads.

Always follow the instructions on the label when washing the belt.

Never machine wash your belt. Always hand wash in lukewarm water.

This protects the internal wiring from damage in the washing

machine. You should take care even when hand washing and never

wring the belt to remove water.

o not use bleach when washing the belt.

o not dry clean your belt.

o not tumble dry your belt. ry the belt on a flat surface. o not dry

it over anything hot. (e.g. a radiator) as the belt contains plastic

parts. Ensure the belt is completely dry before using it again.

The belt should not be ironed.

English

30-day plan

caring or your belt

caring or your pads

• The pads are for single person use only.

• You should ensure your skin is clean and free of oils, creams and other lotions before

use.

• The durability and effectiveness of the pads depends entirely on the proper use, stor-

age and care on the part of the user, certain skin types and the type, duration, num-

ber of sessions, intensity used and site of stimulation.

• Ensure your hands are clean before handling pads. You should avoid touching the skin-

side of the pads with your fingers as much as possible when applying or removing the

belt, as this can transfer oils and skin particles to the pads’ surface.

• After use, replace the liners on the black side of the pads and store your unit in a cool,

dry place until the next use.

• Pads will need to be replaced periodically as the surface picks up skin debris and

becomes dry over time.

All manuals and user guides at all-guides.com

Information Button ( i )

Press the information button any time during a session to

see the highest intensity level you have reached for that

session. Pressing the information button twice shows

you the total number of sessions you have completed

(Fig. a). While pressing the information button three

times shows the belt type you are using.

Mute Function ( )

If you want to switch off your unit’s sound effects,

press and hold the programme button for two seconds

(Fig. b). The mute function remains active indefinitely

unless manually changed. eactivate the mute

function by again pressing the programme button for

two seconds

Keylock Function ( )

If you find a comfortable exercise intensity, press and

hold the information button for two seconds to lock

that intensity (Fig. c). This function only remains active

during the session in which it is activated. If you wish

to increase the intensity further, deactivate the keylock

function by again pressing the information button for

two seconds.

Error Messages

In the unlikely event of your unit developing a problem,

“Err” will appear on your unit display (Fig. d). If this

occurs you should switch the unit off and then switch

it back on again. It should now operate properly. If the

problem persists, please call your local careline for

further assistance (see page 2).

Battery Power / Replacing the battery

The battery icon on the display will flash when the

battery is low and needs to be recharged. After a period

of time, you may find that your battery will only power

your unit for a limited number of sessions, requiring

you to charge the battery more frequently. This is

because rechargeable batteries have a limited number

of charge cycles and may eventually need to be

replaced.

Should you need to replace the rechargeable battery,

remove the small rubber plug from the back cover of

your unit (Fig. e), unscrew the back cover and remove it.

Replace the existing battery pack with a new battery pack

(Fig. f) and replace the battery cover. You can purchase

a new battery pack by contacting the SLEN ERTONE

Careline.

additional unit unctions

Fig. a

Fig. b

Fig. c

Fig. d

Fig. e

Fig. f

All manuals and user guides at all-guides.com

Table des matières

Langues :

Autres manuels Slendertone Équipement de fitness

Slendertone

Slendertone Flex Mini Manuel utilisateur

Slendertone

Slendertone System Arms Manuel utilisateur

Slendertone

Slendertone System Plus Manuel utilisateur

Slendertone

Slendertone Abs8 Manuel utilisateur

Slendertone

Slendertone ABS6 Manuel utilisateur

Slendertone

Slendertone Flex Manuel utilisateur

Slendertone

Slendertone Enervive Manuel utilisateur

Slendertone

Slendertone SYSTEM-ABS Manuel utilisateur

Slendertone

Slendertone ABS7 Manuel utilisateur

Slendertone

Slendertone System Arms Manuel utilisateur

Slendertone

Slendertone Arm Toner Manuel utilisateur

Slendertone

Slendertone Abs5 Manuel utilisateur

Slendertone

Slendertone Flex Go Manuel utilisateur

Slendertone

Slendertone Pulse 530 Manuel utilisateur

Slendertone

Slendertone Abs Manuel utilisateur

Slendertone

Slendertone Face Manuel utilisateur

Slendertone

Slendertone Connect Abs9 Manuel utilisateur

Slendertone

Slendertone Flex Manuel utilisateur

Slendertone

Slendertone System Arms Manuel utilisateur

Slendertone

Slendertone SYSTEM-ABS Manuel utilisateur

Slendertone

Slendertone Flex Manuel utilisateur

Slendertone

Slendertone Flex Manuel utilisateur

Slendertone

Slendertone ABS3 Manuel utilisateur

Slendertone

Slendertone Ultra Manuel utilisateur

Manuels Équipement de fitness populaires d'autres marques

NSD

NSD PB-188P Manuel utilisateur

Performance

Performance HyperVibe Manuel utilisateur

Scalamobil

Scalamobil S27 Manuel utilisateur

Precor

Precor Experience Series Manuel utilisateur

FYTTER

FYTTER RedMIUM BENCH BE-T6R Manuel utilisateur

Taurus

Taurus TF-RK1312 Manuel utilisateur

Nustep

Nustep T5 Manuel utilisateur

Precor

Precor CW-507 Manuel utilisateur

Movement

Movement BICEPS Idea Manuel utilisateur

Kegel8

Kegel8 V For Men Manuel utilisateur

Skandika

Skandika Styrke II Manuel utilisateur

BLK BOX

BLK BOX 21-0122-0B Manuel utilisateur

Stamina

Stamina aeropilates premier 299 Manuel utilisateur

SPORTSTECH

SPORTSTECH PBX300 Manuel utilisateur

ParaBody

ParaBody Serious Steel 877102 Manuel utilisateur

Weslo

Weslo Gym 650 Manuel utilisateur

Rebel

Rebel ACTIVE RBA-1011 Manuel utilisateur

4iiii

4iiii FLiiiight Manuel utilisateur