Sim2 DOMINO DTV S Manuel utilisateur

RSAG2. 025. 7895SS A

SIM2 MULTIMEDIA S.R.L.

Bar code here,

for material number reference only.

Instructions for Laser Projector Use

(DTV S)

Warm Tips

Please carefully read the instructions before using the product and keep it properly.

The company disclaims any responsibility for accidents caused by violating the safety

precautions and instructions in this manual.

Users are not allowed to open the casing without authorization because of high voltage in

this product. Non-professional maintenance personnel shall not repair the product, replace parts or

open the internal optical machine without authorization for the sake of avoiding electric shock and

fire accidents.

Energy Saving Tips:

When the machine is not in use, please select AC shutdown after standby (unplug the power plug)

to reduce energy consumption.

Warning: This product is a Class I device and does not need to be grounded.

Laser safety parameters of the whole device:

Laser safety standard: Class I laser product, meeting the safety standard of GB 7247.1.2012

Radiation parameters:

 Maximum output of laser radiation: ≤ 66mW

 Emission wavelength: Blue ray: 459-471nm

Green ray: 519-531nm

Red ray: 635-651nm

Class 1 laser product do not stare into beam. The bright light may result in permanent

eye damage when the projector is on

Warning and explanation label

III

Symbol Descriptions

This triangle pattern with lightning-shaped arrow is a

warning symbol to remind you that the voltage inside

the product is dangerous.

· Matters needing attention

This triangle pattern with exclamation mark is a

warning symbol to remind you of important

instructions related to the product.

Next step

Important Notes

Please read the following carefully before using this product:

1. Safety Warnings

In case of thunderstorm, please unplug the power plug and the network cable to avoid damage

to the machine.

This product uses the power plug as the power disconnecting device. The socket should be

installed near the product for easy access and sundries cannot be stacked around the socket for the

sake of convenient use.

If you do not use this product for a long time, please unplug the power plug. Do not pull the

power cord when unplugging the power plug.

If you find any abnormal sound or smell, or find that there is only sound but no image on the

machine, please turn off the power immediately, unplug the power plug from the socket, and

contact the after-sales personnel as soon as possible.

 Please do not have any object on the power cord and signal wire.

 Please do not overload the power socket and ensure that the socket you use is a qualified

product passing national safety certification.

 Do not place exposed flame sources (such as lighted candles) on the machine, and keep the

machine away from high-temperature and heating objects.

 Do not expose this machine to water droplets or splashes, or place objects filled with liquids,

such as vases, cosmetics or liquid medicines on the machine.

 If foreign objects or liquids fall into the machine, please pull out the power plug immediately

and contact the after-sales personnel as soon as possible.

 Beware of children standing on or climbing on the machine.

 Condensation may occur to the machine after it is moved from a low-temperature area to a

warm area. In order to make the condensation fully dry inside the machine, it should be

powered on after 24 hours.

 Do not look directly at the lens after the machine is powered on because the strong light

emitted by the lens may hurt your eyes.

 Please do not expose the battery to sunlight, fire and other overheated environment,

otherwise there will be explosion risk.

2. Precautions for Installation and Placement

 The product shall be installed by professionals from the manufacturer. The company

disclaims any responsibility for installation errors, product damage or personal accidents

caused by installation by unqualified personnel.

 The machine should be placed in a flat and stable place, instead of somewhere prone to

shaking.

 Please do not place the machine in high-temperature places where there is direct sunlight or

heating devices, places where water, oil and smoke can easily enter the machine, or places

where there is much dust and is moist.

 Please do not place the machine in a poorly ventilated or enclosed place.

 When the cabinet surface is sprayed with paint or other substances with organic solvent and

grease, the rubber pad of the base may have a slight chemical reaction with it, resulting in

slight corrosion on the cabinet surface. Therefore, we recommend that the user put protective

materials (such as cardboard or glass plate) on the cabinet first before placing the machine.

 We recommend that two or more people load, unload and move the machine. When moving it,

please avoid shocks, and especially protect its light-emitting lens.

 The engineering plastics, insulating varnish on the internal transformer and rubber parts used

for the shell of the newly purchased product will emit certain smell like newly purchased

furniture, and it becomes stronger when the temperature rises. The smell is determined by the

composition of materials. The material solutions we use fully meet national regulations on

environmental protection, so consumers can use them at ease. The smell will gradually

decrease and eventually disappear during the use of machine. Please keep the environment

ventilated.

 The wired network antenna connected to the machine must be isolated from the protective

grounding; otherwise, it may cause fire and other accidents.

 Do not block vents or place sundries on the machine to ensure good heat dissipation effect.

Do not place the machine in a narrow and enclosed space that is not conducive to air

circulation.

 The installation is as shown in the figure. Leave a space around the machine for ventilation.

Top view

At a minimum, leave the amount of space shown in the diagram

below for this device to have proper ventilation.

 Do not install the machine as shown in the figure below.

Insufficient ventilation space may cause this device to overheat or become damaged or even fired.

Laser beam

Confined space (only the

light outlet outward)

VII

3. Precautions for Use

Please do not try to disassemble or repair any part of this device by yourself, which may cause

damage to it and personal injury, and invalidate your product warranty.

If this device gets dirty, please unplug its power plug and wipe it with a semi dried soft cloth

dipped with a small amount of diluted neutral detergent, but do not wipe it repeatedly to avoid

scratching. Do not use alcohol, gasoline, acid, alkali, detergent, volatile oil, diluent and other

solvents to wipe this device because these solvents may deteriorate the materials or damage the

painted surface. If rubber or vinyl products are exposed to this device for a long time, stains may

be caused.

Please do not directly wipe light-emitting lens with your hands, ordinary cleaning paper or

cleaning cloth. For oil stains and fingerprints, please ask professionals to wipe them carefully with

cleaning cloth for optical use, lens wiping paper or professional cleaning solution for the sake of

avoiding damaging the optical coating and affecting the image quality.

Please do not touch the signal connector or reach into the heat dissipation hole with sharp

objects or metal, so as to avoid damage to the product or electric shock caused by short circuit.

Please do not cover this device with articles such as newspapers, tablecloths and curtains, so

as not to hinder ventilation and affect heat dissipation. Otherwise, it may affect the service life of

this device and even cause safety accidents such as fire.

 When this device is working or after it is powered off, do not touch the air vent and upper

cover if they are still touched hot.

 Please do not cut off the power directly when this device is working. If you need to shut

down this device, please press the standby button on the remote control.

 Watch from an appropriate distance. The best distance is 1.5 times the diagonal length of the

screen.

 The volume should be kept appropriate, so as not to disturb the neighbors, especially at night.

VIII

4. Laser

Laser safety parameters of the whole device:

Laser safety standard: Class I laser product, meeting the safety standard of GB 7247.1

Radiation parameters:

 Maximum output of laser radiation: ≤ 66mW

 Emission wavelength: Blue ray: 459-471nm

Green ray: 519-531nm

Red ray: 635-651nm

Safety warnings:

 This product bears a laser module. Do not disassemble or modify this device in a way not

specified in the user manual, otherwise personal injury may be caused.

 Please do not look directly at the laser beam as this is a Class I laser product. If there is a

need to repair it, please wear a laser protective eye mask with OD ≥ 4 and wavelength

ranging from 459 to 651nm

Laser beam

Screen Watching direction

Table des matières

Autres manuels Sim2 Projecteur

Sim2

Sim2 TEATRO 80 Manuel d'utilisation

Sim2

Sim2 Sirio Manuel utilisateur

Sim2

Sim2 Grand Cinema HT 200 Manuel utilisateur

Sim2

Sim2 Domino 20 Manuel utilisateur

Sim2

Sim2 mico50 Manuel d'utilisation

Sim2

Sim2 Grand Cinema HT300 Link Manuel d'utilisation

Sim2

Sim2 Grand Cinema HT380 Instructions de fonctionnement

Sim2

Sim2 PRO5000 Manuel utilisateur

Sim2

Sim2 DLP RS-232C Manuel utilisateur

Sim2

Sim2 D80 Manuel d'utilisation

Sim2

Sim2 Grand Cinema HT 300XTRA-H Manuel d'utilisation

Sim2

Sim2 C3X1080 Manuel d'utilisation

Sim2

Sim2 LUMIS 3D-S Manuel utilisateur

Sim2

Sim2 D10 Manuel utilisateur

Sim2

Sim2 NERO 3D HB Manuel utilisateur

Sim2

Sim2 NERO 3 PLUS Manuel utilisateur

Sim2

Sim2 HT 280E Manuel d'utilisation

Sim2

Sim2 SIM2 Multimedia SpA Manuel utilisateur

Sim2

Sim2 DLINE D35 Manuel utilisateur

Sim2

Sim2 LUMIS20TH Manuel utilisateur

Sim2

Sim2 Grand Cinema HT305 Manuel d'utilisation

Sim2

Sim2 GRAND CINEMA HT HT500 LINK Manuel d'utilisation

Sim2

Sim2 Grand Cinema HT 200 Manuel d'utilisation

Sim2

Sim2 Teatro SVD 500 PLUS Manuel d'utilisation

Manuels Projecteur populaires d'autres marques

iEmmet

iEmmet MP-312 Manuel utilisateur

Epson

Epson VS400 Manuel utilisateur

Sony

Sony VPL-HS10 Marketing Specifications & Features Manuel utilisateur

Sony

Sony VPL-HW65ES Manuel de service

Toshiba

Toshiba TLP-791U Manuel utilisateur

Philips

Philips LC1341 Guide de référence

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Manuel utilisateur

NEC

NEC NP600S EDU Manuel utilisateur

BenQ

BenQ SH753P Manuel utilisateur

Eiki

Eiki EK-623U series Manuel utilisateur

Epson

Epson PowerLite Pro Cinema 6020UB Manuel utilisateur

Epson

Epson PowerLite Home Cinema 705HD Manuel utilisateur

Christie

Christie LHD700 Manuel utilisateur

Navitar

Navitar FX Manuel utilisateur

InFocus

InFocus LitePro 560 Manuel utilisateur

Sony

Sony SRX-R815P Manuel utilisateur

Vivitar

Vivitar DP1500 X Manuel utilisateur

Acer

Acer C20 Series Manuel utilisateur