Siemens RDF310.2/MM Manuel utilisateur

CB1B3066en / 2015-01-28 Subject to change Siemens Building Technologies

Operating Instructions RDF310.2/MM

RDF310.2/MM – thethermostat that allows you toset the ideal room temperature you want. The thermostat provides both

comfort mode and protection mode.

The fan operates either in automatic mode or at the selected speed when using manual mode. You can either rely on the

factory settings or make adjustments that suit your individual needs.

Are your rooms too warm or too cold?

+/ -Only applicable in Comfort mode.

Pressing the +or –button to increase or decrease the current room temperature setpoint for

Comfort mode in increments of 1.0 °C. The setting range is from 5...40 °C, unless it is limited

by parameters P05 and P06.

Do you want to set your controller to protection mode?

Press the button and the symbol shows, indicating that protection mode is selected.

In protection mode , the controller maintains the lower setpoint of heating for frost

protection via parameter P03 or the higher setpoint of cooling for moldy resistance according

to parameter P04.

Important:

If the setpoint of protection is set to OFF, the thermostat will not be activated in protection

mode.

Risk of frost!

Do you want to change the fan mode?

AUTO

Press the button until you have selected the desired fan mode.

In automatic mode, the fan speed is automatically selected by the controller and depends on

the setpoint and the actual room temperature. When the room temperature has reached the

setpoint, the fan either remains in fan speed low (factory setting) or switches off (parameter

P21).

In manual mode the fan operates independently and always runs at the same speed:

Low, medium or high.

The actual fan speed is indicated bythe number of fan symbols.

Low fan speed

Medium fan speed

High fan speed

Do you want to change from heating to cooling mode?

When pressing the button, the controller changes from heating to cooling or vice versa.

If the controller is commissioned cooling only or heating only, no changeover is possible

(please see parameter P22: factory setting manual H/C changeover)

Do you want to calibrate the displayed room temperature?

If the displayed room temperature does not match the actual temperature, the temperature sensor can be

calibrated by modifying parameter P07.

Proceed as described under “Changing the control parameters” and follow steps 1 through 3

to select parameter P07.

In step 4, modify the displayed room temperature to match the actual temperature.

Each pressing of the +or -button changes the temperature in increments of 0.5 °C and up to

a range of ±3 °C.

In step 7, the calibration is automatically stored 10 seconds after the last readjustment.

Display

Operation and Settings

Low fan speed

Medium fan speed

High fan speed

AUTO Auto Automatic fan

active

Cooling mode

Heating mode

Comfort mode

Protection mode

Measured room temperature,

setpoints and parameters

Actual room

temperature symbol

Heating/cooling

changeover button

to change manually between

heating and cooling mode

Button for changing of

fan operating and

protection mode

- Protection ( )

- Automatic fan speed (AUTO)

- Manual fan speed ( )

Colder / Warmer

Setting the temperature setpoints

Selectable temperature unit

CB1B3066en / 2015-01-28 Subject to change Siemens Building Technologies

Changing the control parameters

To optimize the control performance, you can use local HMI to adjust a number of control parameters. Proceed as follows to change the

control parameters (see the table of “Commissioning by qualified HVAC staff” for factory settings):

+/ -

1. Set the thermostat to protection mode .

2. Press and hold down the +and –buttons simultaneously for 3 seconds. Release them and,

within 2 seconds, press and hold down the +button for 3 seconds. The display shows P03.

3. Select the required parameter by pressing the +or –button as follows:

4. Press the +and –buttons simultaneously. The current value of the selected parameter displays on the screen.

Press the +or -.button to change the value.

5. You can either press the +and -buttons simultaneously to confirm the change, or wait

for 5 seconds to have the change saved automatically.

6. Repeat step 3 through 5 to change more parameters.

7. 10 seconds after the last display, all changes are saved and it returns to protection mode.

8. Press the button to switch to Comfort mode .

Commissioning (by qualified HVAC staff)

Para-

meter Description Factory

setting Setting range Adj.!

P03 Setpoint of heating in protection (WheatStb)8 °C OFF, 5 °C…WcoolStb

P04 Setpoint of cooling in protection (WcoolStb)OFF OFF, WheatStb …40 °C

P05 Minimum setpoint limitation in Comfort mode (WminNorm)5 °C 5 °C…WmaxNorm

P06 Maximum setpoint limitation Comfort mode (WmaxNorm)35 °C WminNorm…40 °C

P07 Sensor calibration 0 K -3…3 K

P08 Switching differential heating SDH 1 K 0.5…4 K

P09 Switching differential cooling SDC 1 K 0.5…4 K

P14 Dwelling time of auto fan speeds 2 min. 1…5 minutes

P17 Selection of °C or °F °C °C or °F

P18 Display of room temperature or setpoint ON OFF: Setpoint

ON: Room temperature

P21 Fan control in normal operation (Comfort mode) ON OFF in dead zone

ON in dead zone

P22 Heating/cooling mode 3:Manual

H/C

changeover

0: Heating only

1: Cooling only

3: Manual H/C changeover

!Please record all changes you make.

Visit https://www.downloads.siemens.com/download-center/ to download the latest documentations and applications.

Autres manuels pour RDF310.2/MM

Table des matières

Autres manuels Siemens Thermostat

Siemens

Siemens REV200.03RF Manuel utilisateur

Siemens

Siemens RDH100 Manuel utilisateur

Siemens

Siemens Albatros RVS46 Series Manuel utilisateur

Siemens

Siemens ZIEHL TR 1200 Manuel utilisateur

Siemens

Siemens RDS110.R Manuel utilisateur

Siemens

Siemens QMX3.P37 Manuel utilisateur

Siemens

Siemens QAX34.1 Manuel utilisateur

Siemens

Siemens EcoView 97-004 Manuel utilisateur

Siemens

Siemens RDH10RF Mode d'emploi

Siemens

Siemens RDE100 Series Manuel utilisateur

Siemens

Siemens RDF510.2 Manuel utilisateur

Siemens

Siemens REA23 Manuel utilisateur

Siemens

Siemens RDG140 Manuel utilisateur

Siemens

Siemens RDG20 KN Series Manuel de l'opérateur

Siemens

Siemens Powers TH 188 Manuel du propriétaire

Siemens

Siemens RDJ100 Manuel d'installation

Siemens

Siemens RDF880KN Series Manuel utilisateur

Siemens

Siemens Albatros2 RVS46 Series Manuel utilisateur

Siemens

Siemens EcoView Manuel utilisateur

Siemens

Siemens RDG100KN Manuel utilisateur

Siemens

Siemens REV24 Manuel utilisateur

Siemens

Siemens RDE100 Series Manuel

Siemens

Siemens RDF301 Manuel utilisateur

Siemens

Siemens TH 192 S Manuel utilisateur

Manuels Thermostat populaires d'autres marques

EWELLY

EWELLY EW-181 Manuel utilisateur

Prolon

Prolon T1100 Instructions d'installation

Computherm

Computherm Q20 Manuel utilisateur

Heatmiser

Heatmiser neoStat Manuel utilisateur

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur

Saswell

Saswell SAS920XWHB-7-S-RF Mode d’emploi

Aircalo

Aircalo TFP1-ET85P2 Manuel utilisateur

Honeywell

Honeywell CM721 Manuel utilisateur

Carrier

Carrier DEBONAIR 33CS Manuel utilisateur

Lennox

Lennox iHarmony Zone Thermostat Instructions de montage

Gemtech

Gemtech GT7000 Mode d’emploi

Rollei

Rollei Smartes 45000 Manuel utilisateur

Sinope

Sinope TH1300RF Manuel utilisateur

Honeywell

Honeywell RLV4305 Manuel utilisateur

Honeywell

Honeywell Prestige 2.0 THX9421 Manuel utilisateur

NuTone

NuTone NTBZ48 Instructions d'utilisation d'origine

Stelpro

Stelpro MAESTRO ASMT402AD Manuel utilisateur