Siemens RDF301 Manuel utilisateur

3171

RDF301, RDF600KN RDF301.50 RDF301.50H

Semi flush-mount

communicating room

thermostats

RDF301

RDF301.50

RDF600KN

For 2

-pipe, 2-pipe with electrical heater, and 4-pipe fan coil units

For use with compressors in DX type equipment

•KNX bus communications (S-mode and LTE mode)

•Backlit display

•2P / PI / P control

•Outputs for on/off or 3-position control

•Outputs for 3-speed or 1-speed fan

•2 multifunctional inputs for keycard contact, external sensor, etc.

•Operating modes: Comfort, Economy and Protection

•Automatic or manual fan speed control

•Automatic or manual heating/cooling changeover

•Minimum and maximum limitation of room temperature setpoint

•Control depending on the room or the return air temperature

•Adjustable commissioning and control parameters

•Commissioning with Synco ACS, ETS or via local HMI

•Integration into Synco

•Integration into Desigo and Apogee via group addressing (ETS) or via

individual addressing

•Integration into third-party system via group addressing (ETS)

•AC 230 V operating voltage

CE1N3171en

2014-05-23

Building Technologies

Additional RDF600KN features:

•Independent function for window contact and presence detector

Additional RDF301.50 features:

•Four buttons to control KNX actuators via KNX S-mode

(functions: switching, dimming, blinds control, 8-bit scene)

Additional RDF301.50H features:

•Four buttons for hotel functions MUR (Make Up Room), DND (Do Not

Disturb) via KNX S-mode

Type of mounting / suitable conduit boxes:

•RDF600KN for round box, with min 60 mm diameter, min 40 mm depth

and recessed rectangular box with 60.3 mm fixing centers

•RDF301... for recessed rectangular box with 60.3 mm fixing centers

Use

Room temperature control (heating or cooling) in individual rooms and zones by

means of:

•2-pipe fan coil units

•2-pipe fan coil units with electrical heater

•4-pipe fan coil units

•Compressors in DX-type equipment

•Compressors in DX-type equipment with electrical heater

The RDF301... / RDF600KN controls:

•One single or 3-speed fan

•One or two on/off valve actuators

•One on/off valve actuator and one 1-stage electrical heater

•One 3-position valve actuator

•One 1-stage compressor in DX-type equipment, or one 1-stage compressor with

electrical heater

Used in systems with:

•Heating or cooling mode

•Automatic heating/cooling changeover

•Manual heating/cooling changeover

•Heating and cooling mode (e.g. 4-pipe system)

The room thermostats are delivered with a fixed set of applications.

The relevant application is selected and activated during commissioning using one

of the following tools:

•Synco ACS

•ETS

•Local DIP switch and HMI

Functions

•Room temperature control via built-in temperature sensor or external room

temperature / return air temperature sensor.

•Changeover between heating and cooling mode (automatically via local sensor

or bus, or manually).

•Selection of applications via DIP switches or commissioning tool.

•Selection of operating mode via operating mode button on the thermostat.

2 / 17

Siemens RDF301, RDF301.50..., RDF600KN CE1N3171en

Building Technologies Semi flush-mount communicating room thermostats 2014-05-23

•Temporary Comfort mode extension.

•1- or 3-speed fan control (automatically or manually).

•Display of current room temperature or setpoint in °C and/or °F.

•Minimum and maximum limitation of room temperature setpoint.

•Button lock (automatically and manually).

•2 multifunctional inputs, freely selectable for:

−Sensor for automatic heating / cooling changeover

−External room temperature or return air temperature sensor

−Dew point sensor

−Electric heater enable

−Fault input

−Monitor input for temperature sensor or switch state

RDF301…:

−Operating mode switchover contact … (keycard, window contact, etc )

RDF600KN:

−Window contact

−Presence detector

•Advanced fan control function, e.g. fan kick, fan start, selectable fan operation

(enable, disable or depending on heating or cooling mode).

•Purge function together with 2-port valve in a 2-pipe changeover system.

•Reminder to clean fan filters (adjust with P62).

•Floor heating temperature limitation.

•Reload factory settings for commissioning and control parameters.

•KNX bus (terminals CE+ and CE-) for communication with Synco or KNX

compatible devices.

•Display of outdoor temperature or time of day via KNX bus.

•Time scheduling and central control of setpoints via KNX bus.

•With a Synco RMx7xx controller, the energy demand signal of the thermostat is

used to optimize energy supply.

RDF301.50 only:

•Four buttons to control KNX actuators via KNX S-mode.

("switching groups" with functions such as switching, dimming, blinds control,

8-bit scene).

RDF301.50H only:

•Four buttons for Hotel applications to control via KNX S-mode.

Same functions as RDF301.50, but with dedicated button labels for hotel

applications: Make Up Room (MUR), Do Not Disturb (DND).

Applications

The thermostats support the following applications, which can be configured using

the DIP-switches on the inner side of the thermostat's front panel or a commissio-

ning tool.

All DIP switches need to be set to OFF (remote configuration, factory setting) to

select an application via commissioning tool.

Remote configuration

, via commissioning tool (factory set)

•Synco ACS

•ETS

DIP switches

2 3

Remote configuration

3 / 17

Siemens RDF301, RDF301.50..., RDF600KN CE1N3171en

Building Technologies Semi flush-mount communicating room thermostats 2014-05-23

Applications for fan coil systems

Application and output signal, DIP switches, diagram

•2-pipe fan coil unit ON/OFF

(heating or cooling)

2 3

•2-pipe fan coil unit with el. heater

(heating or cooling) ON/OFF

2 3

3076D20

(B1)

3171D21

B2 YE

(B1)

•2-pipe fan coil unit 3-position

(heating or cooling)

2 3

•4-pipe fan coil unit ON/OFF

(heating and cooling)

2 3

3076D20

(B1)

3076D22

(B1)

4 / 17

Siemens RDF301, RDF301.50..., RDF600KN CE1N3171en

Building Technologies Semi flush-mount communicating room thermostats 2014-05-23

Applications for Universal systems

Application and output signal, DIP switches, diagram

•Chilled / heated ceiling ON/OFF

(heating or cooling)

2 3

•Chilled / heated ceiling with electric

heater (heating or cooling) ON/OFF

2 3

3191S11

3191S12

•Chilled / heated ceiling 3-position

(heating or cooling)

2 3

•Chilled ceiling and radiator ON/OFF

(heating and cooling)

2 3

3191S11

3191S13

5 / 17

Siemens RDF301, RDF301.50..., RDF600KN CE1N3171en

Building Technologies Semi flush-mount communicating room thermostats 2014-05-23

Applications for heat pump systems

Application and output signal, DIP switches, diagram

•1-stage compressor ON/OFF

(heating or cooling)

2 3

•1-stage compressor with electric

heater (heating or cooling)

ON/OFF

2 3

3181S31

3181S32

•1-stage compressor ON/OFF

(heating and cooling)

2 3

3181S35

Y1 Heating or heating / cooling

valve actuator

B1 Return air temperature sensor or external

room temperature sensor (optional)

Y2 Cooling valve actuator

B2 Changeover sensor (optional)

YE Electric heater

M1 3- or 1-speed fan

Key

6 / 17

Siemens RDF301, RDF301.50..., RDF600KN CE1N3171en

Building Technologies Semi flush-mount communicating room thermostats 2014-05-23

Type summary

Product no. Stock no. Operating

voltage

Control outputs

Suitable

conduit

box 2)

pos

ON/

OFF

0..10 V

KNX switching

groups

RDF301

S55770-T104

AC 230 V

1 1)

2 1)

rectangular

RDF301.50

S55770-T105

AC 230 V



rectangular

RDF301.50H

S55770-T334

AC 230 V

1 1)

2 1)

Hotel: MUR, DND 3)

rectangular

RDF600KN S55770-T293 AC 230 V 1

-- round &

rectangular

1) Selectable: ON/OFF or 3-position.

2) Rectangular conduit box e.g. ARG71.

Round CEE conduit box min 60 mm diameter and min 40 mm depth.

3) MUR: Make Up Room, DND: Do Not Disturb.

Ordering

•When ordering, indicate both product number / SSN number and name:

E.g. RDF301 / S55770-T104 room thermostat

•Order valve actuators separately.

Equipment combinations

Type of unit Product no. Data

sheet

Cable temperature sensor or changeover

sensor

QAH11.1 1840

Room temperature sensor

QAA32 1747

Condensation monitor

QXA2601 /

QXA2602 /

QXA2603 /

AQX2604

3302

Electromotoric ON/OFF actuator

SFA21... 4863

Electromotoric ON/OFF valve and

actuator

(only available in AP, UAE, SA and IN)

MVI…/MXI… 4867

Zone valve actuators

(only available in AP, UAE, SA and IN)

SUA… 4832

Thermal actuator (for radiator valves),

STA23... 4884

Thermal actuator

(for small valves 2.5 mm), NC

STP23... 4884

On/off actuators

7 / 17

Siemens RDF301, RDF301.50..., RDF600KN CE1N3171en

Building Technologies Semi flush-mount communicating room thermostats 2014-05-23

Electrical actuator, 3-position

(for radiator valve)

SSA31... 4893

Electrical actuator, 3-position

(for 2- and 3-port valves / V…P45)

SSC31 4895

Electrical actuator, 3-position

(for small valve 2,5 mm)

SSP31… 4864

Electrical actuator, 3-position

(for small valve 5,5 mm)

SSB31... 4891

Electrical actuator, 3-position

(for small valve 5,5 mm)

SSD31... 4861

Electromotoric actuator, 3-position

(for valves 5.5 mm)

SQS35… 4573

For the maximal number of actuators in parallel, refer to information in the data sheets

of the selected actuators and to this list, depending on which value is lower:

•Parallel operation of max 6 SS… actuators (3-pos) is possible.

•Parallel operation of max 10 on/off actuators is possible.

•Parallel operation of SQS35 is not possible.

Accessories

Designation Product no / SSN

Data

sheet

Changeover mounting kit

(50 pcs/package)

ARG86.3 N3009

Plastic mounting bracket for semi-

flush-mount thermostats RDF301... for

increasing the headroom in the conduit

box by 10mm

ARG70.3 N3009

Conduit box for semi-flush mounted

thermostat RDF301...

ARG71 /

S55770-T137 N3009

KNX Power supply 160 mA (Siemens BT LV)

5WG1 125-1AB02

KNX Power supply 320 mA (Siemens BT LV)

5WG1 125-1AB12

KNX Power supply 640 mA (Siemens BT LV)

5WG1 125-1AB22

3-position actuators

Note:

8 / 17

Siemens RDF301, RDF301.50..., RDF600KN CE1N3171en

Building Technologies Semi flush-mount communicating room thermostats 2014-05-23

Mechanical design

The thermostats consist of 2 parts:

•Front panel with electronics, operating elements and built-in room temperature

sensor.

•Mounting base with power electronics.

The rear of the mounting base contains the screw terminals.

Slide the front panel in the mounting base and snap on.

Operation

and

settings

RDF301, RDF600KN

RDF301.50

RDF301.50H

1 Operating mode selector

2 Change fan operation

3 Adjust setpoint and control parameters

4 Four buttons to control KNX actuators via KNX S-mode

(functions: switching, dimming, blinds control, 8-bit scene)

5 Four dedicated buttons for hotel functions (Make Up Room, Do Not Disturb)

via KNX S-mode (functions: switching)

Display

1 Operating mode

Protection

Comfort

Economy

Auto Timer according to

schedule (via KNX)

2 Displays room temperature, set-

points and control parameters.

Symbol indicates current room

temperature

3 Fan mode

Auto fan active

Fan speed

low, medium, high

4 Heating/cooling mode

Cooling

Heating

Electrical heater active

Condensation in room

(dewpoint sensor active)

6 Indicates fault or reminder

7 Temporary comfort mode

extension active

8 Additional user information, like

outdoor temperature or

time of day from KNX bus.

Selectable via parameters

9 Button lock active

Weekday 1…7 from KNX bus

(1 = Monday / 7 = Sunday)

RDF301.50

RDF301.50H

2 5

3 8

4 4 5

1 2

9 / 17

Siemens RDF301, RDF301.50..., RDF600KN CE1N3171en

Building Technologies Semi flush-mount communicating room thermostats 2014-05-23

Engineering notes

See the "Reference documentation", page 15 for information on how to engineer

the KNX bus (topology, bus repeaters, etc.) and how to select and dimension

connecting cables for supply voltage and field devices.

Mounting and installation

Mount the room thermostat on a conduit box. Do not mount on a wall in niches or

bookshelves, behind curtains, above or near heat sources, or exposed to direct

solar radiation. Mount about 1.5 m above the floor.

Mounting / Dismounting

•Mount the room thermostat on a clean, dry indoor place without direct airflow

from a heating / cooling device, and not exposed to drips or splash water.

•RDF301… : In case of limited space in the conduit box use the mounting

bracket ARG70.3 to increase the headroom by 10mm

•Before removing the front cover, disconnect the power supply.

Wiring See the mounting instructions M3171... and M3076.1 enclosed with the

thermostat.

•Comply with local regulations to wire, protection and earth the thermostat.

•The device has no internal fuse for supply lines to fan and actuators. To avoid

risk of fire and injury due to short-circuits, the AC 230 V mains supply line must

have a circuit breaker with a rated current of no more than 10 A.

•Properly size the cables to the thermostat, fan and valve actuators for

AC 230 V mains voltage.

•Use only valve actuators rated for AC 230 V.

•The wiring cross section used for power supply (L, N), fan (Q1, Q2, Q3,N) and

230 V outputs (Yx -N) must be adapted to the preceding overload protection

elements (10A) under all circumstances. Comply under all circumstances with

local regulations

•Cables of SELV inputs X1-M/X2-M: Use cables with 230 V insulation, as the

conduit box carries AC 230 V mains voltage.

•Inputs X1-M or X2-M of different units (e.g. summer/winter switch) may be

connected in parallel with an external switch. Consider overall maximum

contact sensing current for switch rating.

•KNX communication cables (input CE+ / CE-): Use cables with 230 V

insulation, as the conduit box carries AC 230 V mains voltage.

•No metal conduits.

•No cables provided with a metal sheath.

•Disconnect from supply before opening the cover.

•When a KNX bus power supply is connected on the line with communicating

thermostats and Synco controller, the internal KNX power supply of the Synco

controllers must be switched off.

10 / 17

Siemens RDF301, RDF301.50..., RDF600KN CE1N3171en

Building Technologies Semi flush-mount communicating room thermostats 2014-05-23

Autres manuels pour RDF301

Ce manuel convient aux modèles suivants

Autres manuels Siemens Thermostat

Siemens

Siemens RDD100.1RFS Manuel utilisateur

Siemens

Siemens Connected Home RDZ100ZB Manuel utilisateur

Siemens

Siemens RDG165KN Manuel utilisateur

Siemens

Siemens RDG400 Guide d'installation

Siemens

Siemens RDG400 Manuel utilisateur

Siemens

Siemens RDF302 Manuel de l'opérateur

Siemens

Siemens RDS110 Manuel utilisateur

Siemens

Siemens RAA20 Manuel utilisateur

Siemens

Siemens BRTRF Manuel utilisateur

Siemens

Siemens RDG1 series Manuel utilisateur

Siemens

Siemens DF301 Manuel de l'opérateur

Siemens

Siemens RDH100RF/SET Manuel utilisateur

Siemens

Siemens RDG100KN Manuel de l'opérateur

Siemens

Siemens QAA73.110 Manuel de l'opérateur

Siemens

Siemens RDE100 Series Manuel

Siemens

Siemens RAA02 Series Manuel utilisateur

Siemens

Siemens RDJ100RF/SET Manuel utilisateur

Siemens

Siemens KNX RDF600KN Manuel utilisateur

Siemens

Siemens RDF510 Series Manuel utilisateur

Siemens

Siemens RAM1T Mode d’emploi

Siemens

Siemens RDG100KN Manuel utilisateur

Siemens

Siemens KNX RDF301.50H Manuel utilisateur

Siemens

Siemens RCR10/868 Manuel utilisateur

Siemens

Siemens RDE100.1 Manuel utilisateur

Manuels Thermostat populaires d'autres marques

EWELLY

EWELLY EW-181 Manuel utilisateur

Prolon

Prolon T1100 Instructions d'installation

Computherm

Computherm Q20 Manuel utilisateur

Heatmiser

Heatmiser neoStat Manuel utilisateur

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur

Saswell

Saswell SAS920XWHB-7-S-RF Mode d’emploi

Aircalo

Aircalo TFP1-ET85P2 Manuel utilisateur

Honeywell

Honeywell CM721 Manuel utilisateur

Carrier

Carrier DEBONAIR 33CS Manuel utilisateur

Lennox

Lennox iHarmony Zone Thermostat Instructions de montage

Gemtech

Gemtech GT7000 Mode d’emploi

Rollei

Rollei Smartes 45000 Manuel utilisateur

Sinope

Sinope TH1300RF Manuel utilisateur

Honeywell

Honeywell RLV4305 Manuel utilisateur

Honeywell

Honeywell Prestige 2.0 THX9421 Manuel utilisateur

NuTone

NuTone NTBZ48 Instructions d'utilisation d'origine

Stelpro

Stelpro MAESTRO ASMT402AD Manuel utilisateur