Siemens Flange Mount Kit Manuel utilisateur

DPD01156B Siemens Industry, Inc.

Flange Mount Kits for Frames FS4 to FS7

Mounting Instructions

General

Using the optional Flange Mounting Kit, you can mount your drive through the cabinet wall or similar surface

so that the control unit of the drive remains inside the cabinet.

The correct installation of the Flange Mounting Kit might affect the IP or UL protection class of the drive. If

your drive is protected according to Type12/IP54, or your drive is supplied with flange option at the factory,

you only need to install the collars, as instructed. However, the power module of a Type1/IP21-protected drive

will only become protected according to Type12/IP54 on the rear side (see figure below), if all parts of the

flange mounting kit are installed properly. The need for this has to be evaluated and these actions are

explained in this guide.

Figure 1. Example of the flange mounting.

BT9070

CABINET WALL

OR SIMILAR

CABINET

WALL OR

SIMILAR

REAR

TYPE 12/

IP54

IP00

FRONT

Siemens Industry, Inc. DPD01156B

Flange Mount - Frames FS4 - FS7

Figures 2. - 5. present the dimensions of the drives with the flange mount option. Figure 6. present the

dimensions of the opening and the drive outline with the flange.

Use the embossed holes or self-clinching nuts in the back plate when mounting the drive to ensure proper

sealing.

Figure 2. FS4, flange mount, dimensions.

152 (5.98)

15 (.59)

122 (4.80)

Ø7(.27)

285 (11.22) 24 (.94)

113 (4.44)

357 (14.05)

341 (13.42)

101.6 (4)

72.1 (2.83)

18.5 (.72)

32.8 (1.29)

39 (1.53)

77 (3.03)

190 (7.48)

134 (5.27)

128 (5.03)

186.9 (7.35)9 (.35)

BT11134

DPD01156B Siemens Industry, Inc.

Figure 3. FS5, flange mount, dimensions.

BT11132

Ø7(.27)

436 (17.16)

454.1 (17.87)

262.5 (10.33)

145 (5.70)

144 (5.66)

150 (5.90)

169 (6.65)

9 (.35)

13 (.51) 382 (15.03) 24 (.94)

39 (1.53)

33 (1.29)

27,5 (1.08)

100 (3.93)

214 (8.42)

114 (4.48)

11.5 (.45)

72.2 (2.84)

145 (5.70)

101.9 (4.01)

12 (.47)

Siemens Industry, Inc. DPD01156B

Figure 4. FS6, flange mount, dimensions

DPD01156B Siemens Industry, Inc.

Figure 5. FS7, flange mount, dimensions

Siemens Industry, Inc. DPD01156B

Figure 6. Flange mount cutout and drive outline dimensions for FS4 to FS7.

Table 1. Flange mount cutout dimensions for FS4 to FS7 in mm (in).

Frame A B C D E

FS4 315 (12.40) 137 (5.39) 357 (14.05) 152 (5.98) 24 (.94)

FS5 408 (16.06) 152 (5.98) 454 (17.87) 169 (6.65) 23 (.90)

FS6 541 (21.29) 203 (7.99) 580 (22.83) 220 (8.66) 23 (.90)

FS7 655 (25.78) 240 (9.44) 680 (26.77) 286 (11.25) 13 (.51)

11136.emf

flange

cutout

outline

DPD01156B Siemens Industry, Inc.

Flange Mount Kit for Frame FS4

The kit consists of:

1. Top collar, (70CMR00281)

2. Bottom collar, (70CMR00280)

3. Side collars (2 pcs), (70CMR00282)

4. Internal fan, (70CPE00132, 70CPE00056) depends on the

control unit

5. Sealing plug (3 pcs), (70CMR00324)

Additionally:

• 8 screws size 4x16 (for the top and bottom collar mounting)

• 3 screws size 4x12 (for the side collar mounting)

• 2 screws size 3.5x10 (for the bottom collar mounting)

FS4 Flange Mounting

If your drive is the Type 1/IP21-protected and there is the risk that dust or other impurities in the cooling air

might end up inside the control unit, start the mounting with actions described in the steps 1 to 4.

If this is not needed, install the flange mounting kit proceeding directly to the step 5. Note, in this case the rear

will not be according to the Type 12/IP54.

9266.emf

M3.5x10

M4x12

M4x16

Siemens Industry, Inc. DPD01156B

Remove the cover of the drive.

Lift up the I/O protection plate.

The location of the internal fan

depends on the control unit.

If you have the control unit presented

in the upper picture, slide the internal

fan into the opening with the label

facing the cabling end of the drive.

If you have the control unit presented

in the lower picture, install the internal

fan with the label facing downwards.

11147.emf

11150.emf

DPD01156B Siemens Industry, Inc.

2Connect the power wire to the power

connector. The location of the power

connector depends on the control unit.

3Remove the main fan.

11148.emf

11149.emf

9289.emf

Siemens Industry, Inc. DPD01156B

Insert the three sealing plugs into

position where indicated.

Remount the main fan carefully,

checking its position.

Attach the side collars with three

screws size 4x12. The tightening

torque for the screws is 2 Nm (17.70

lbf-in).

Important! Do not yet screw the fourth

screw in the bottom right hole.

11151.emf

9287.emf

Autres manuels Siemens Support et étagère

Siemens

Siemens SENTRON 3VL160 Manuel utilisateur

Siemens

Siemens VNT-MP Manuel utilisateur

Siemens

Siemens 3VL800-1250 Manuel utilisateur

Siemens

Siemens 3AS110B Manuel utilisateur

Siemens

Siemens 8PQ9801-0AA00 Manuel utilisateur

Siemens

Siemens 8PQ9801-0AA08 Manuel utilisateur

Siemens

Siemens FDFB291 Manuel utilisateur

Siemens

Siemens 8PQ9800-6AA24 Manuel utilisateur

Siemens

Siemens 8PQ9800-4AA21 Manuel utilisateur

Siemens

Siemens Actavix ASK33 Manuel utilisateur

Siemens

Siemens d800 Manuel utilisateur

Siemens

Siemens 8MF1-2AA.20 Series Manuel utilisateur

Siemens

Siemens 8PQ9800-7AA38 Manuel utilisateur

Siemens

Siemens SIPART PS2 Manuel utilisateur

Siemens

Siemens 3WL/3WA/4000A Manuel utilisateur

Siemens

Siemens SIMATIC IPC647D Manuel utilisateur

Siemens

Siemens 8PQ9801-2AA15 Manuel utilisateur

Siemens

Siemens 8PQ9800-4AA83 Manuel utilisateur

Siemens

Siemens d1000 Manuel utilisateur

Siemens

Siemens 8PQ9802-7AA11 Manuel utilisateur

Siemens

Siemens ASK77 2 Series Manuel utilisateur

Siemens

Siemens SIRIUS 3TX7680-1B Manuel utilisateur

Siemens

Siemens AP-220-MNT-W3 Manuel utilisateur

Siemens

Siemens 8GK4 801-2KK13 Guide de l'utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur