Siemens SANTIS-ab Manuel utilisateur

User Manual for

SANTIS-ab

Subscriber Access and

Network Termination for ISDN Services

2

U

mains

230VAC / 50Hz

LED for local feeding

SIEMENS

LED for remote feeding

a/b1 a/b2

S S

3

Contents

1. Safety Instructions.....................................................................4

2. Operating Modes .......................................................................5

3. Installation.................................................................................6

4. Configuration ............................................................................8

5. Table of Configuration Commands......................................... 12

6. Troubleshooting ......................................................................26

7. Pin Allocations of the Sockets ................................................27

4

1. Safety Instructions

•Place the SANTIS-ab near a 230 V outlet.

•Do not open the case.

•Clean the case only with dry or moist cloth.

Never immerse into water.

•If the SANTIS-ab is damaged, inform immediately your

network provider.

5

2. Operating Modes

The connection to the public telephone network as well as the

selection of one of the following three operating modes must be

done by an authorized person, e.g. telecom staff:

1. NT+2ab S- and a/b-interfaces available

2. NTBA Only S-interface available

3. Pairgain Only a/b-interfaces available

6

3. Installation

•If both the green LEDs light steadily, the SANTIS-ab is ready

for operation (see figure on page 2).

The following installation-steps can be done by everyone.

•The SANTIS-ab can be wall-mounted or placed on the desk

(piling of more units is also possible). In case of wall

mounting, drill the holes into the wall according to the

enclosed drawing, insert dowels with wood screws and hang

on the SANTIS-ab.

7

•Connection of the terminal equipments:

The sockets for the analog equipments (e.g. telephones, gr.2/3

fax machines, modems) are designated with «a/b1» and

«a/b2», those for the ISDN terminal equipments with «S»

(e.g. ISDN-telephones, PC with ISDN-card, gr.4 fax

machines). See figure on page 2.

8

4. Configuration

•There are only parameters for the a/b-interfaces. Thus there is

only a need for a configuration, if the a/b-interfaces are

available (NT+2ab mode and Pairgain mode; see chapter 2).

The configuration remains stored, even after a power failure.

•The configuration is done by means of an analog telephone

set equipped with tone dialing, having both ∗and #keys.

Remark:

In normal use SANTIS-ab recognizes both pulse and tone

dialing.

•If the NT+2ab mode is selected, all the configuration

commands can be set from both the a/b-interfaces without

any restrictions.

9

If the configuration access (CA) is restricted (can be set and

changed by authorized persons, e.g. telecom staff), the

configuration for the a/b1-interface can only be done via the

a/b1-interface and vice versa for the a/b2-interface.

This mode is called NT+2ab/CA restr.

If the Pairgain mode is selected, the configuration access is

automatically restricted, i.e. the configuration for the a/b1-

interface can only be done via the a/b1-interface and vice

versa for the a/b2-interface.

10

The settings are executed as follows. See also flow chart on next

page.

1. Hook off and wait for dial tone

2. Dial ∗∗→The dial tone is switched off

3. Dial the command number and parameter value according to

the tables in chapter 5.

4. Dial #→If the parameter has been programmed

successfully, a permanent tone is switched on.

Otherwise a busy tone will be switched on.

5. Proceed with step 3. if necessary for setting other parameters

or hook on.

Table des matières

Autres manuels Siemens Matériel réseau

Siemens

Siemens RUGGEDCOM RX1400 Manuel utilisateur

Siemens

Siemens SINUMERIK 840Di sl Manuel de la liste des pièces

Siemens

Siemens SIMATIC NET S7-400 Manuel utilisateur

Siemens

Siemens SIVACON 8PS BD01 Series Manuel utilisateur

Siemens

Siemens RUGGEDCOM WIN7251 Manuel utilisateur

Siemens

Siemens RUGGEDCOM WIN5149 Manuel utilisateur

Siemens

Siemens SIMATIC NET Manuel utilisateur

Siemens

Siemens RUGGEDCOM WIN5251 Manuel utilisateur

Siemens

Siemens Rider 11, Rider 13 H,Rider 11 Bio Manuel d'instructions

Siemens

Siemens SIMATIC NET Feuille d'instructions

Siemens

Siemens SIMATIC NET PROFIBUS Manuel utilisateur

Siemens

Siemens SIVACON 8PS BD2 Series Manuel utilisateur

Siemens

Siemens SCALANCE W788C-2 Manuel utilisateur

Siemens

Siemens XT55 AVL Manuel utilisateur

Siemens

Siemens SIMATIC NET Manuel utilisateur

Siemens

Siemens RUGGEDCOM RX1511 Manuel utilisateur

Siemens

Siemens RUGGEDCOM WIN5114-V Manuel utilisateur

Siemens

Siemens SIMATIC NET PROFIBUS OBT Manuel utilisateur

Siemens

Siemens SIMATIC NET RUGGEDCOM RX1536 Manuel utilisateur

Siemens

Siemens SICAM SGU 7XV5676 Manuel utilisateur

Siemens

Siemens SIMATIC NET Manuel utilisateur

Siemens

Siemens NK8000 MP.4.60 Manuel de la liste des pièces

Siemens

Siemens SIMATIC NET CP 1515 Manuel utilisateur

Siemens

Siemens FastConnect RJ45 Plug 90 Manuel utilisateur

Manuels Matériel réseau populaires d'autres marques

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuel utilisateur

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuel utilisateur

Yudor

Yudor YDS-16 Manuel utilisateur

D-Link

D-Link ShareCenter DNS-320L Manuel utilisateur

Samsung

Samsung ES1642dc Instructions d'utilisation

Honeywell Home

Honeywell Home LTEM-PV Instructions de montage

evertz

evertz 7700 Series Manuel utilisateur

D-Link

D-Link ShareCenter DNS-343 Manuel utilisateur

Asante

Asante AsanteBridge 1012 Manuel utilisateur

FireBrick

FireBrick FB2700 Manuel utilisateur

Audiovox Electronics

Audiovox Electronics ARWH2T Manuel utilisateur

ADC

ADC DSX-1 Manuel

NetComm

NetComm NF2 Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 5620 Manuel utilisateur

Dell EMC

Dell EMC XC6420 Series Manuel utilisateur

Lanner

Lanner NCA-1020A Manuel utilisateur

Allied Telesis

Allied Telesis AT-TN121-A Manuel utilisateur

Arista

Arista CCA-ETM-Q12 Manuel utilisateur