Siemens FPI-32 Manuel utilisateur
MODEL FPI-32
PROGRAMMER/TESTER
Operations Manual
Siemens Industry, Inc.
BuildingTechnologies Division
Florham Park, NJ
Siemens BuildingTechnologies, Ltd.
Fire Safety & Security Products
2 Kenview Boulevard
Brampton, Ontario
L6T 5E4 Canada
P/N 315-090077-10
firealarmresources.com
The FPI-32 Programmer/Tester was developed to be user-
friendly. Most users will find that it can be operated by simply
responding at the keypad to the displays shown.
This manual is available to the user to present an overview of
the Programmer/Tester and for ready reference.
IMPORTANT NOTE
TO ALL PREVIOUS USERS OF THE FPI-32
PROGRAMMER/TESTER:
Due to the implementation of the advanced searching algo-
rithm, devices connected to the TRI/MSI input jack of the
FPI-32 must be connected with the correct polarity. If a de-
vice is not found by the programmer/tester, simply reverse
the input leads and the device should be found within three
seconds. If the display continues to read Searching for De-
vice, the connected device may be inoperable.
firealarmresources.com
TABLE OF CONTENTS
PAG E
OPERATION 1
Modes of Operation 3
Keypad 4
Power On/Off Sequences 5
PROGRAM MODE 7
Entering the Program Mode 7
Verifying the Device Type and Address 8
TRI Devices 9
Selecting Normally Open (NO) or Normally Closed (NC)
for TRI Devices 10
Verifying Device Information for TRI Devices 11
Backward Compatibility Mode 12
Changing the Device ID 12
Establishing an Address 13
Completing the Programming 14
TEST MODE 16
Entering the Test Mode 16
Device Passed 17
Device Failed 17
MENU MODE 18
FPI-32 Menu Mode 21
firealarmresources.com
Changes to the FPI-32
There have been a significant number of changes made to the FPI-32
from Revision 1.3. These changes provide ease of use and more com-
prehensive compatibility with MXL. The changes are summarized below.
Automatic Searching Algorithm
The FPI-32, when placed in any operational mode (Program, Test, or
Menu), will automatically recognize when a device has been inserted
and/or removed. This simplifies and reduces the number of keystrokes
needed to operate the FPI-32. Generally, the searching algorithm will
properly identify devices within 5 seconds.
Polarity Sensitive
For the searching algorithm to identify each device, the FPI-32 must
have external devices such as TRI/MSI, etc., connected with the proper
polarity. When one of these devices is connected improperly, the searching
algorithm will not find the device. In this case, the display on the FPI-32
reminds the user to try swapping the connect wire to find the device.
Backward Compatibility Device Setting
The FPI-32, in conjunction with certain devices, can be used to replace
older devices. This backward compatibility mode is an enhancement to
and replaces the FPI-32 Revision 1.3 user options 1=MXL and 2=MXL.
Menu Mode
The new Menu Mode provides powerful field debugging capabilities. The
Menu Mode on the FPI-32 Revision 3.2 performs requested MXL wave-
forms (polls) and displays the data returned from the programmed
device.
XL3 Waveforms
The FPI-32 no longer performs XL3 waveforms to test devices. Device
acceptance is based on passing MXL device checking waveforms.
firealarmresources.com
1
FIGURE 1
THE MODEL FPI-32 PROGRAMMER/TESTER
OPERATION
The Model FPI-32 Programmer/Tester is used in the field to program or
test any ID-60 Series detectors, IL Series detectors, FP Series detec-
tors, MSI Series manual stations, or TRI modules. Refer to Figure 1
below for identification of the parts of the FPI-32.
OPERATION
Instruction
label
Operating
keys
Connect manual
stations and
TRI modules here
Place
detector
here
Handle
Instruction
label
Plug for
manual stations
and TRI modules
Operating
keys
Voltage
adjuster
Carrying
Strap
firealarmresources.com
OPERATION
CONNECTING THE PROGRAMMER/TESTER
The FPI-32 comes provided with a wall transformer with one end that
plugs into any standard AC power outlet and a cable at the other end that
connects to the back of the Programmer/Tester unit, where marked AC/
BATTERY RECHARGE. This connection not only provides the AC power
used by the unit, but also automatically recharges the batteries in the
unit for use where the unit cannot be plugged in.
BATTERIES
The batteries used in the unit are sealed, nickel-cadmium, rechargeable
batteries, Size AA. If the batteries need to be replaced, two different
makes of batteries are recommended for use in the Programmer/Tester:
Panasonic P/N P-50AA or Yuasa P/N 500AA
(The Programmer/Tester operates for approximately 4 hours using its
batteries.)
Siemens Industry, Inc. recommends that the batteries be recharged on a
regular basis. Overnight charging is usually sufficient.
When the batteries are low, the LOW BATTERY indicator flashes. When
it flashes, plug in the charger. If you ignore the indicator, the battery will
keep getting lower until the following message displays: PLUG IN
CHARGER!, and the Programmer/Tester will not operate. Then when the
charger is plugged in, the Programmer/Tester powers up again (restarts).
INSTALLATION OF DEVICES ON THE FPI-32
Install any intelligent initiating device on the Programmer/Tester in order
to program or test it.
To install a detector on the Programmer/Tester, place the detec-
tor over the base on the Programmer/Tester by lining up the LED on
the detector with the LED symbol on the base, push in on the detec-
tor, and turn it clockwise at the same time. To remove the detector
from the Programmer/Tester, again push in on it, but in this case
turn it counterclockwise.
To install an FP-11 or FPT-11 detector on the Programmer/Tester,
first install the DB-ADPT adapter over the base. Only the FP-11 and
FPT-11 require the use of the DB-ADPT adapter. Do not use the
DB-ADPT with any other devices.
2
firealarmresources.com
OPERATION
To connect a TRI or MSI device to the Programmer/Tester, use
the cable provided and connect one end to the module and the other
to the rear of the FPI-32 where marked TRI/MSI. Note that there is
an indentation on the surface of the Programmer/Tester where the
module may be rested.
CAUTION
1. TO PREVENT DAMAGE TO THE FPI-32, DO NOT CONNECT
CZM-1s, TRIs/MSIs, or ICPs/VCPs to the FPI-32 until all wiring
is removed from the CZM-1, term 1 and 2, the TRI/MSI, term 1
and 2, or the ICP/VCP, TB1, term 1 and 2.
2. Only one device should be connected to the FPI-32 at a time.
MODES OF OPERATION
The Programmer/Tester has three modes: PROGRAM Mode, TEST Mode,
and MENU Mode.
NOTE: Units equipped with an LED will blink red in all three modes.
This is not an indication that the device is in alarm, but rather
an indication that the LED is functional.
The PROGRAM Mode is used to program the following information to
the devices installed on the FPI-32:
All Devices
1. The address of the device.
TRl Series Devices only
2. The normal state of the contact [normally open (NO) or nor-
mally closed (NC)] on a switch-type device.
3. Whether a device is an alarm, trouble, or status type device.
The keypad on the Programmer/Tester is used to do the programming (See
below). Refer to the PROGRAM MODE Section (page 7).
After the device is programmed, it is automatically tested.
The TEST Mode is used to test a device. By making entries on the keypad,
the user can check on whether a device is working before it is installed, as
well as checking it periodically after installation. Refer to the TEST MODE
Section (page 16).
3
firealarmresources.com
ON
OFF
PROG
TEST
MENU
YES
NO
C
NUMBER KEYS
To turn on the power to the FPI-32
To turn off the power to the FPI-32
To program the device
To test the device
To use the troubleshooting features
To answer Yes to a question displayed
To answer No to a question displayed
To clear any current user entry and return
to the previous text
To enter device addresses, etc.
KEY FUNCTION
KEYPAD
FUNCTIONS OF THE KEYS
OPERATION
4
In addition, the MENU Mode provides a special set of operations for techni-
cians who are familiar with and can interpret device analog response wave-
forms and wish to perform some troubleshooting. Refer to the MENU MODE
Section (page 18) for instructions on these operations.
firealarmresources.com
POWER ON/OFF SEQUENCES
To Power Up
To turn on the power, press the ON key. The Display then changes
between the following two messages for the time periods shown.
CERBERUS
PYROTRONICS
and
SELECT MODE
PROG TEST MENU
(PROG = program)
Once the Programmer/Tester is turned on, pressing ON again has no
effect on the Programmer/Tester.
To Power Down
1. To turn the power off, press the OFF key.
2. If there are no keys pressed for 5 minutes, the Programmer/Tester
turns off its own power to save the batteries.
NOTE: The first time the FPI-32 is powered up, the following message
displays for about 2 seconds.
FPI-32
SOFTWARE REV. 3.2
OPERATION
5
1 second
3 seconds
firealarmresources.com
USING THE KEYPAD
1. The following keys may be used at any time:
PROG To program the device (Programmer/Tester
enters PROGRAM Mode)
TEST To test the device (enters TEST Mode)
MENU To use additional features (enters MENU
Mode)
2. If the wrong key is pressed at any time, the FPI-32 Display
shows:
INCORRECT KEY
ENTRY...!
After 1 second the previous message displays.
3. All displayed messages are abbreviated when necessary to
fit into two lines, with no more than 16 characters per line.
OPERATION
6
firealarmresources.com
Table des matières
Autres manuels Siemens Carte mère
Siemens
Siemens SITRANS 7ML1930-1BK Guide de l'administrateur
Siemens
Siemens SIMATIC VPU200/560 Manuel du propriétaire
Siemens
Siemens SIMATIC PG 760 PII Manuel
Siemens
Siemens ERTEC EB 200 Manuel utilisateur
Siemens
Siemens SIMATIC PG 760 Manuel utilisateur
Siemens
Siemens SIMATIC Field PG M6 Manuel utilisateur
Siemens
Siemens Simatic PG 740 Manuel utilisateur
Siemens
Siemens MMB-3 Manuel utilisateur
Siemens
Siemens D1085-A Manuel utilisateur
Siemens
Siemens ET 200 Manuel utilisateur
Siemens
Siemens D981 Manuel utilisateur
Siemens
Siemens D1107 Manuel utilisateur
Siemens
Siemens SIMATIC PG 720 P Manuel utilisateur
Siemens
Siemens DPU Manuel utilisateur
Siemens
Siemens Simatic PG 740 PIII Manuel utilisateur
Siemens
Siemens SIMATIC Field PG M5 Manuel utilisateur
Siemens
Siemens SIMATIC PG 720 Manuel utilisateur
Siemens
Siemens SIMATIC EB 200P-3 Document technique
Siemens
Siemens RWB29 Manuel utilisateur
Siemens
Siemens D992 Manuel utilisateur
Manuels Carte mère populaires d'autres marques
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manuel utilisateur
Gigabyte
Gigabyte GA-9IVDT Manuel utilisateur
Texas Instruments
Texas Instruments ADS8372EVM Manuel utilisateur
Commell
Commell MS-C73 Manuel utilisateur
IBT Technologies
IBT Technologies MB860 Manuel utilisateur
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur
