Siemens SIMADYN D EB11 Manuel utilisateur

SIMADYN D

Digital Control System

I/O module EB11

User Manual

Edition 05.95 DK-Nr. 231141

User Manual, I/O module EB11

Edition Edition status

1I/O module EB11 06.93

2I/O module EB11 05.95

Copying of this document and giving it to others and the use or

communication of the contents thereof is forbidden without express

authority. Offenders are liable to the payment of damages. All rights

are reserved in the event of the grant of a patent or the registration of

a utility model or design.

We have checked the contents of this Manual to ensure that they

coincide with the described hardware and software. However,

deviations cannot be completely ruled-out, so we cannot guarantee

complete conformance. However, the information in this document is

regularly checked and the necessary corrections included in

subsequent editions. We are thankful for any recommendations or

suggestions.

Contents

Siemens AG Dk-Nr. 231141 Edition 05.95

SIMADYN D Hardware User Manual

Contents

Warning information....................................................................................................................1

1. Description..............................................................................................................................3

2. Module construction................................................................................................................3

3. Notes for the user....................................................................................................................3

4. Technical specification............................................................................................................6

5. Connector pin assignments of the EB11..................................................................................7

6. STRUC-L menu of the EB11 module in the master program...................................................8

7. Miscellaneous.........................................................................................................................9

7.1. Appendices..............................................................................................................9

7.1.1. Figures......................................................................................................9

7.1.2. Drawings...................................................................................................9

8. ECB instructions......................................................................................................................10

Warning information

Edition 05.95 Siemens AG Dk-Nr. 231141

SIMADYN D Hardware User Manual

Warning information

Siemens AG Dk-Nr. 231141 Edition 05.95 1

SIMADYN D Hardware User Manual

N O T E !

The information in this Manual does not purport to cover all details or variations in equipment, nor to provide

for every possible contingency to be met in connection with installation, operation or maintenance.

Should further information be desired or should particular problems arise which are not covered sufficiently for

the purchaser’s purposes, please contact your local Siemens office.

Further, the contents of this Manual shall not become a part of or modify any prior or existing agreement,

committment or relationship. The sales contract contains the entire obligation of Siemens. The warranty

contained in the contract between the parties is the sole warranty of Siemens. Any statements contained

herein do not create new warranties nor modify the existing warranty.

Warning information

W A R N I N G !

Electrical equipment has components which are at dangerous voltage levels.

If these instructions are not strictly adhered to, severe bodily injury and material

damage can result.

Only appropriately qualified personnel may work on this equipment or in its

vicinity.

This personnel must be completely knowledgeable about all the warnings and

service measures according to this User Manual.

The successful and safe operation of this equipment is dependent on proper

handling, installation, operation and maintenance.

Warning information

2Edition 05.95 Siemens AG Dk-Nr. 231141

SIMADYN D Hardware User Manual

Definitions

*QUALIFIED PERSONNEL

For the purpose of this User Manual and product labels, a „Qualified person“ is someone who is familiar with the

installation, mounting, start-up and operation of the equipment and the hazards involved. He or she must have

the following qualifications:

1. Trained and authorized to energize, de-energize, clear, ground and tag circuits and equipment in accordance

with established safety procedures.

2. Trained in the proper care and use of protective equipment in accordance with established safety

procedures.

3. Trained in rendering first aid.

*DANGER

For the purpose of this User Manual and product labels, „Danger“ indicates death, severe personal injury and/or

substantial property damage will result if proper precautions are not taken.

*WARNING

For the purpose of this User Manual and product labels, „Warning“ indicates death, severe personal injury or

property damage can result if proper precautions are not taken.

*CAUTION

For the purpose of this User Manual and product labels, „Caution“ indicates that minor personal injury or

material damage can result if proper precautions are not taken.

*NOTE

For the purpose of this User Manual, „Note“ indicates information about the product or the respective part of the

User Manual which is essential to highlight.

C A U T I O N !

This board contains components which can be destroyed by electrostatic

discharge. Prior to touching any electronics board, your body must be electrically

discharged. This can be simply done by touching a conductive, grounded object

immediately beforehand (e.g. bare metal cabinet components, socket protective

conductor contact).

W A R N I N G !

Hazardous voltages are present in this electrical equipment during operation.

Non-observance of the safety instructions can result in severe personal injury or

property damage.

It is especially important that the warning information in all of the relevant

Operating Instructions are strictly observed.

Description

Siemens AG Dk-Nr. 231141 Edition 05.95 3

SIMADYN D Hardware User Manual

1. Description

The external EB11 module is used in the SIMADYN D system for the input and output of binary

information. The two 40-way ribbon cable connectors X5 and X6 (with equal priority) on the frontplate

are each organized in groups of 4 x 10 pins, each ten pins being organized in eight bits of information

and an external power supply P24 and ground. The four units of a connector are divided into two units

for input and two for output.

The S1 and S2 pushbuttons with integral LEDs also located on the frontplate are used for the visual

indication of output inhibit signals (LED function) and/or for the manual resetting of output inhibit

signals (pushbutton function). Pushbutton S1 is assigned to connector X5 and pushbutton S2 to

connector X6.

Output inhibits occur at output bits that are overloaded. The pushbutton LEDs can only be used to

determine which overloaded output bit(s) is(are) assigned to which connector.

The inputs and outputs have a rated voltage of 24 V. The inputs load the source with 5 mA and the

outputs supply 50 mA.

2. Module construction

- 1 plug-in station (corresponds to 1 1/3 SPS for standard plug-in stations)

- SIMADYN D local bus connection

- Programmable address decoder (PAD) with module identification

- 2 x 2 x 8-bit inputs

- 2 x 2 x 8-bit outputs (switched off on thermal overload and switched back on see 'Notes for the

user')

- 2 LED pushbuttons

3. Notes for the user

The EB 11 external module can be installed both in each SIMADYN D rack and is connected to the

local bus. It takes up one plug-in station in the subrack.

The module only functions properly if it is screwed down in position in the subrack (also during

commissioning).

If the module is plugged onto an adapter, the frontplate or, even better, one of the two frontplate end

pieces, must be connected with chassis by a short cable.

The binary inputs/outputs are connected via interface modules that are snapped onto the mounting

rail. The connections from the module (connector X5/X6) to the interface modules are established

with a ribbon cable (both cable ends with ribbon cable socket connectors).

Notes for the user

4Edition 05.95 Siemens AG Dk-Nr. 231141

SIMADYN D Hardware User Manual

The following options (shown in figure 1, appendix) are provided for connecting each of the two

connectors X5 and X6 (shown only for X5):

Re a) All 16 binary inputs/outputs of the EB 11 (connector X5/X6) are connected to the SE3.1/SE23

interface module via a 40-way ribbon cable. This module contains the externalconnections to

the plant (screw-type terminals).

Re b) The 16 binary inputs/outputs of a connector are distributed over four different interface

modules. This is done by splitting the ends of a ribbon cable (4 x 10-way) and running it to the

various interface modules. This makes it possible, to connect 8 inputs/outputs at a time via

different interface modules to the plant (e. g. with/without isolation, changing 48 V to 24 V or 24

V to 48 V).

An output channel is switched off (output = 0 V) on thermal overload (e. g. by short circuit). The LED

of the appropriate connector turns on. The output can be switched back to normal operation after

cooling the output element by a few degrees Celsius.

This reset operation is normally be done by a test program running in the background. It is called in

time distances like the SIMADYN D monitor.

Therefore much variable periods can exist between the occurance of overload and the automatic

reset by the background program. On a very high processor load conditioned by configuring it is also

thinkable, that the background program is called never or only after a long time.

In this case all the affected outputs of a connector can be reset by the pushbutton function of the LED

pushbutton.

Additional components used for the EB 11:

a) Binary I/O cable

* 40-way 2.0 m SC18 6DD 1684-0BJ0

* 40-way --> 4+10-way 2.0 m SC13 6DD 1684-0BD0

If cables in other lengths are needed, all the necessary informations for manufacturing can be taken

from the dimension drawings.

Dimension drawings

cable type No. of dimension drawing

* 40-way 3GE 465 684 9000.01 MB

* 40-way --> 4+10-way 3GE 465 684 9000.02 MB

Notes for the user

Siemens AG Dk-Nr. 231141 Edition 05.95 5

SIMADYN D Hardware User Manual

b) Interface module

* SE3.1 6DD 1681-0AD1

16 non-floating binary inputs and 16 non-floating binary outputs

* SE23 6DD 1681-0CD0

16 binary inputs and 16 binary outputs (40-way one-to-one connection)

* SE8 6DD 1681-0AJ0

Eight binary inputs or outputs (10-way one-to-one connection)

* SE4.1 6DD 1681-0AE1

Eight non-floating binary inputs or outputs

* SE5.3 6DD 1681-0AF3

Eight 220 V floating binary inputs

* SE6.1 6DD 1681-0AG1

Eight floating binary outputs for max. 220V

* SE37 6DD 1681-0DH0

Eight 24 V floating binary outputs

* SE41.1 6DD 1681-0EB1

Eight floating 48 V binary inputs

* SE41.2 6DD 1681-0EB2

Eight floating 24 V binary inputs

Technical specification

6Edition 05.95 Siemens AG Dk-Nr. 231141

SIMADYN D Hardware User Manual

4. Technical specification

GENERAL

INSULATION GROUP B to VDE 0110 paragraph 13, group 2 at 24 V DC,

15V, 5 V DC

AMBIENT TEMPERATURE 0 to 55 deg. C with forced ventilation

STORAGE TEMPERATURE -40 to +70 deg. C

HUMIDITY CLASS F to DIN 40040

ALTITUDE RATING S to DIN 40040

MECHANICAL STRESS Installation in stationary equipment,

sensitive to vibrations

PACKAGING SYSTEM ES 902 C

DIMENSIONS 233.4 x 220 mm

MODULE WIDTH 1 1/3 SPS = 1 plug-in station = 20.14 mm

WEIGHT 0.6 kg

CURRENT CONSUMPTION P5 0.4 A

P15 0.0 A

N15 O.02 A

P24 0.2 A (from external supply)

+ current consumption of conn. interf. m.

+ current consumption of binary outputs

BINARY INPUTS

QUANTITY 32

INPUT VOLTAGE + 24 V rated valu&e

FOR 0 SIGNAL -1 V to +6 V; or binary inputs open

FOR 1 SIGNAL +13 V to +33 V

INPUT CURRENT

AT 1 SIGNAL 5 mA (typ.)

DELAY TIME 200 us

BINARY OUTPUTS

QUANTITY 32

SUPPLY VOLTAGE

- RATED VALUE 24 V DC

- RIPPLE 3.6 V DC

- PERM. RANGE +20 to +30 V including ripple

- SHORT-TIME OVERLOAD +35 V T < 0.5 s

OUTPUT CURRENT AT 1 SIGNAL

- RATED VALUE 50 mA

- PERM. RANGE 0.2 mA to 50 mA

SHORT-CIRCUIT PROTECTIONelectronic

LIMITATION OF VOLTAGE INDUCED

ON CIRCUIT INTERRUPTION to VP + 1 V

TOTAL LOAD 80 % at 50oC, all outputs with 50 mA

RESIDUAL CURRENT 20 uA at 0 signal

SIGNAL LEVEL

- 0 SIGNAL 3 V max.

- 1 SIGNAL -2.5 V min. supply voltage

DELAY 15 us

Table des matières

Autres manuels Siemens Système d'E/S

Siemens

Siemens ION PROFIBUS DP SPY T001 Manuel utilisateur

Siemens

Siemens FDCI181-2 Manuel utilisateur

Siemens

Siemens SIMATIC Manuel utilisateur

Siemens

Siemens SIMATIC ET 200C Manuel utilisateur

Siemens

Siemens SIMATIC ET 200SP Manuel utilisateur

Siemens

Siemens N 263E11 Manuel utilisateur

Siemens

Siemens SIMATIC ET 200S Manuel utilisateur

Siemens

Siemens Simatic S7-1500 Manuel utilisateur

Siemens

Siemens SIMATIC ET 200R Manuel utilisateur

Siemens

Siemens Simatic S7-1500 Manuel utilisateur

Siemens

Siemens SIMATIC PROFINET Manuel de la liste des pièces

Siemens

Siemens SIMATIC 6ES7134-4FB01-0AB0 Manuel utilisateur

Siemens

Siemens SIM-16 Manuel utilisateur

Siemens

Siemens SIMATIC ET 200SP Manuel utilisateur

Siemens

Siemens SIMATIC ET 200SP HA Manuel utilisateur

Siemens

Siemens FDCI222 Manuel utilisateur

Siemens

Siemens SIMATIC RQ 4x120VDC-230VAC/5A CO HA Manuel utilisateur

Siemens

Siemens SIMATIC ET 200eco Manuel utilisateur

Siemens

Siemens Simatic ET200pro Manuel utilisateur

Siemens

Siemens SIMATIC ET 200AL Manuel utilisateur

Siemens

Siemens SIMATIC ET 200eco PN Document technique

Siemens

Siemens Simatic S7-1500 Document technique

Siemens

Siemens SIMATIC ET 200AL Guide de l'utilisateur

Siemens

Siemens Simatic S7-1500 Manuel de la liste des pièces

Manuels Système d'E/S populaires d'autres marques

WAGO

WAGO 750-344 Manuel utilisateur

Teknim

Teknim TWM-1887 Mode d’emploi

Intelligent Appliance

Intelligent Appliance IA-2662-E Manuel utilisateur

BERGHOF

BERGHOF ECC DIO 16/16 Mode d’emploi

Advantech

Advantech PCM-27J3AU Manuel d'installation et d'exploitation

Festo

Festo CP-E08-M12-CL Manuel utilisateur

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manuel utilisateur

Hitachi

Hitachi HX-RIO3 Series Manuel utilisateur

NUUO

NUUO SCB-A08 Manuel utilisateur

M-system

M-system R3Y-RS8 Manuel utilisateur

jablotron

jablotron JB-110N Manuel utilisateur

Omron

Omron SYSMAC C200H Manuel utilisateur

DOLD

DOLD SAFEMASTER M Manuel utilisateur

ABB

ABB OPT-MF-001 Manuel utilisateur

Omron

Omron SYSMAC C2000H Manuel utilisateur

Helmholz

Helmholz TB20 Manuel utilisateur

ICP DAS USA

ICP DAS USA tM-AD2 Manuel utilisateur

Automationdirect.com

Automationdirect.com DL305 Manuel utilisateur