Siemens SIM-16 Manuel utilisateur

Siemens Building Technologies

Fire Safety

P/N 315-034060-3

A24205-A334-B825

Supervised Input Module (500-034060 / S24235-B112-A2)

Installation Instructions

Model SIM-16

INTRODUCTION The SIEMENS Model SIM-16 Supervised Input Module

is a remotely located, general purpose input module. It

provides sixteen input circuits for remote system

monitoring. Each input can be individually programmed

as supervised (dry contacts only) or unsupervised

(general-purpose input). The SIM-16 has two Form C

relays. The relays and the inputs are programmable using

the Zeus Programming Tool.

OPERATION The SIM-16 is mounted in an enclosure that is remotely

located from the Main Panel. Communication between

the SIM-16 and the NIC-C (Network Interface Card) or

the next CAN module (in CE applications) is through the

Control Area Network (CAN) bus. Up to 99 SIM-16s can

be used with a single NIC-C or a DAC-NET (in CE

applications).

Each SIM-16 has two 10-position rot ary switches that

are used to set the board address on the CAN which is

a sub-address of the NIC-C or the DAC-NET (in CE

applications).

Every time a change of state of the input is detected, a

unique CAN message is sent to the NIC-C (DAC-NET).

A CAN message from the NIC-C (DAC-NET) directed

to the SIM-16 controls the Form C relays.

PRE-INSTALLATION Rotary Address Switches - Set the board address for

each SIM-16 using both of the ten-position rotary

switches located on the board (See Figure 1). Each of

these addresses must be a sub-address of the NIC-C

or the DAC-NET (in CE applications) and must be the same as the addresses

assigned in the Zeus Programming Tool.

Figure 1

SIM-16 Supervised Input

Module

12345678

910111213141516

TB2

TB1

S1 S2

TB3

TB4

SIM-16

Siemens Building Technologies

Fire Safety

P/N 315-034060-3

A24205-A334-B825

INSTALLATION A SIM-16 may be installed in a REMBOX or in an enclosure on mounting plate MP-

OM (in CE applications). When using REMBOX 2 or 4, mount the SIM-16 in one

module space on a REMBOX2-MP, P/N 500-634211 or REMBOX4-MP, P/N 500-

634212 using the four screws provided. (Refer to REMBOX2-MP/REMBOX4-MP

Installation Instructions, P/N 315-034211.) Up to 4 SIM-16s will fit in a REMBOX2;

up to 8 SIM-16s will fit in a REMBOX4.

WIRING Refer to Figures 2-6.

Disconnect BATTERY and AC prior to working on equipment.

• Each SIM-16 module is a node in the CAN bus.

• The SIM-16 can be inst alled with or without an RNI. Connect the CAN bus

and 24V as shown in Figures 2 and 3.

• Up to 99 CAN modules, in any combination, can be connected to the CAN

bus of each NIC-C or the CAN bus of the DAC-NET (in CE applications).

• Each SIM-16 module is shipped with one CCS cable.

•Cable connections for SIM-16 modules are shown in the following t able:

SNOITCENNOCELBAC61-MIS

elbaCnoitpircseDrebmuNtraPnoitcennoC

LCCgnoL-ELBAC-NAC

-6,)mc001(.ni03

rotcudnoc

412436-995

6K-1A-53242C

oslA.61-MIStsrifotINRno4PstcennoC

/MCFot61-MISmorfstcennoc

.)roodno(seludomBSC/MCS/MCL

SCCtrohS-ELBAC-NAC

-6,)mc41(.ni½5

rotcudnoc

935331-555

4K-1A-53242C

ro61-MISotseludom61-MISstcennoC

worelgnisaniseludom61-MCO

The CAN bus requires a 120Stermination at each end of the loop. Refer to the NIC-C

Installation Instructions, P/N 315-033240 / A24205-A334-B824 or DAC-NET Installation

Instructions P/N 315-035100 / A24205-A334-B839 for details about CAN termination.

Siemens Building Technologies

Fire Safety

P/N 315-034060-3

A24205-A334-B825

Figure 3

SIM-16 Wiring Without An RNI

NOTES

1. All wiring supervised.

2. All wiring power limited to

NFPA 70 per NEC 760.

3. Wiring for TB1 and TB2 is

18 AWG (1.0mm2) min.,

12 AWG (4mm2) max.

4. Wiring for TB3 and TB4 is

26 AWG (∅ 0.25mm) min.,

16 AWG (1.5mm2) max.

5. CAN network max. line

resistance 16S.

6. Refer to the NIC-C

Installation Instructions, P/N

315-033240 / A24205-

A334-B824 for CAN

network termination

instructions.

Figure 2

SIM-16 CAN Bus Connections With An RNI

Siemens Building Technologies

Fire Safety

P/N 315-034060-3

A24205-A334-B825

Figure 4

SIM-16Relay Connections

NOTES

1. Contacts are unsupervised.

2. 1A max @ 24VDC resistive.

3. All wiring must remain

inside the enclosure or

within 20 feet (6.5m) in

rigid conduit.

4. Wiring for TB1 and TB2 is

18 AWG (1.0mm2 ) min.,

12 AWG (4mm2) max.

5. Wiring for TB3 and TB4 is

26 AWG (∅ 0.25mm) min.,

16 AWG (1.5mm2) max.

COM

N.C.

N.O.

COM

N.C.

N.O.

Relay 1

Relay 2

TB3

TB4

SIM-16

87654321

16 15 14 13 12 11 10 9

TB2

ELECTRICAL RATINGS

tnerruCenalPkcaBV420

tnerruCV42lanimreTwercS

Am02

tupnidesivrepus/Am2.1+

yalerevitca/Am02+

tnerruCenalPkcaBV2.60

tnerruCybdnatSV42

Am02

tupnidesivrepus/Am2.1+

yalerevitca/Am02+

Siemens Building Technologies

Fire Safety

P/N 315-034060-3

A24205-A334-B825

Figure 5

SIM-16 Supervised Input Wiring

NOTES

1. All inputs supervised.

2. All inputs power limited to

NFPA 70 per NEC 760.

3. Wiring for TB1 and TB2 is

18 AWG (1.0mm2 ) min.,

12 AWG (4mm2) max.

4. Maximum distance 500 feet

(165m) from SIM-16 to

supervised input.

5. In the Zeus Programming

Tool, select supervised for

each supervised input.

6. Supervised and unsuper-

vised inputs may be mixed

on a single SIM-16.

Figure 6

SIM-16 Unsupervised Input Wiring

NOTES

1. All inputs unsupervised.

2. All inputs power limited to

NFPA 70 per NEC 760.

3. Wiring for TB1 and TB2 is

18 AWG (1.0mm2 ) min.,

12 AWG (4mm2) max.

4. All inputs must remain

inside the enclosure or

within 20 feet (6.5m) in

rigid conduit.

5. In the Zeus Programming

Tool, select unsupervised for

each unsupervised input.

6. Supervised and unsuper-

vised inputs may be mixed

on a single SIM-16.

12345678

87654321

910111213141516

16 15 14 13 12 11 10 9

SIM-16

TB1

TB2

TYPICAL

CONNECTION

(16 PLACES)

*6.8K

*SUPPLIED WITH

THE SIM-16

INPUT #2

INPUT #6

INPUT #16

INPUT #5

INPUT #9

12345678

87654321

910111213141516

16 15 14 13 12 11 10 9

SIM-16

TB1

TB2

TYPICAL

CONNECTION

(16 PLACES)

INPUT #2

INPUT #1

INPUT #6

INPUT #16

INPUT #5

INPUT #9

Siemens Building Technologies

Fire Safety

P/N 315-034060-3

A24205-A334-B825

Siemens Building Technologies, Inc.

8 Fernwood Road

Florham Park, New Jersey 07932

Siemens Building Technologies, Ltd.

2 Kenview Boulevard

Brampton, Ontario L6T 5E4 CN

P/N 315-034060-3

A24205-A334-B825

Siemens AG

I BT DE FS SYS

D-81379 München

For CE applications in Cerberus E100 systems refer to

Installation Instruction A24205-A334-B844 (English) or A24205-A334-A844 (German).

Table des matières

Autres manuels Siemens Système d'E/S

Siemens

Siemens Simatic S7-1500 Document technique

Siemens

Siemens SICAM AI Manuel utilisateur

Siemens

Siemens EA12 Manuel utilisateur

Siemens

Siemens 6DL2804 Series Instructions de montage

Siemens

Siemens Binary Input N 260 Manuel utilisateur

Siemens

Siemens SIMATIC ET 200SP Manuel utilisateur

Siemens

Siemens S7-I/O Manuel utilisateur

Siemens

Siemens Simatic S7-1500 Manuel utilisateur

Siemens

Siemens Simatic ET200pro Manuel utilisateur

Siemens

Siemens SIMATIC ET 200SP Manuel utilisateur

Siemens

Siemens SIMATIC ET 200SP Manuel utilisateur

Siemens

Siemens SIMATIC ET 200SP Manuel utilisateur

Siemens

Siemens SIMATIC ET 200SP DI 8x24VDC ST Manuel utilisateur

Siemens

Siemens 262E01 Manuel utilisateur

Siemens

Siemens SIMATIC ET 200S Manuel utilisateur

Siemens

Siemens Simantic ET 200S Manuel utilisateur

Siemens

Siemens Simatic ET200pro Manuel utilisateur

Siemens

Siemens Simatic CFU Guide de démarrage rapide

Siemens

Siemens SIMATIC ET 200SP Manuel utilisateur

Siemens

Siemens SIMATIC ET 200S Manuel utilisateur

Siemens

Siemens SIMATIC ET 200S Manuel utilisateur

Siemens

Siemens ZN-31U Manuel utilisateur

Siemens

Siemens SIMATIC ET 200SP Manuel utilisateur

Siemens

Siemens Simatic ET200pro Manuel utilisateur

Manuels Système d'E/S populaires d'autres marques

WAGO

WAGO 750-344 Manuel utilisateur

Teknim

Teknim TWM-1887 Mode d’emploi

Intelligent Appliance

Intelligent Appliance IA-2662-E Manuel utilisateur

BERGHOF

BERGHOF ECC DIO 16/16 Mode d’emploi

Advantech

Advantech PCM-27J3AU Manuel d'installation et d'exploitation

Festo

Festo CP-E08-M12-CL Manuel utilisateur

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Manuel utilisateur

Hitachi

Hitachi HX-RIO3 Series Manuel utilisateur

NUUO

NUUO SCB-A08 Manuel utilisateur

M-system

M-system R3Y-RS8 Manuel utilisateur

jablotron

jablotron JB-110N Manuel utilisateur

Omron

Omron SYSMAC C200H Manuel utilisateur

DOLD

DOLD SAFEMASTER M Manuel utilisateur

ABB

ABB OPT-MF-001 Manuel utilisateur

Omron

Omron SYSMAC C2000H Manuel utilisateur

Helmholz

Helmholz TB20 Manuel utilisateur

ICP DAS USA

ICP DAS USA tM-AD2 Manuel utilisateur

Automationdirect.com

Automationdirect.com DL305 Manuel utilisateur