Siemens AE-30U Manuel utilisateur

P/N 315-085099-16

Operation and Installation Instructions

Model AE-30U

Alarm Extender Module

Fire Safety

Operation

The SIEMENS Model AE-30U Alarm Extender

Module is designed to provide one Style Y (Class

) super-vised notification appliance circuit,

utilizing polarized, parallel connected notification

appliances.

Actuation of the module is caused by

high-going DC input signal between 12 and 24 volts

above system common. Dual input activation termi-

nals are provided to facilitate programming.

The Model AE-30U contains a yellow LED trouble

indicator to display open or shorted alarm lines

except when that particular module is not in an

activated condition.

The yellow LED can be lamp tested from the

system control panel.

Installation

1. Mount the module to the horizontal mounting

brackets in the control enclosure.

2. Install the Model JA-5 (5 in. long) bus connector

cable assembly between receptacle P2 of the

module and receptacle P1 of the module or

control panel immediately preceding it in the

bus.

Note: If the preceding module is on another

row in the enclosure, a JA-24 (24 in.

long) bus connector cable assembly will

be required.

3. Modules are to be bus-connected from right to

left. For two-row enclosures, the modules in the

lower row are to be connected from left to right.

Succeeding rows are to be alternately con-

nected, right to left, left to right, etc.

4. If a module is the last module in the system,

install either a JS-30 (30 in. long) or JS-64

(64 in. long) bus connector assembly from the

unused receptacle of the last module to

terminal 41 of the CP-35 control panel. This

completes the module supervision circuit.

5. If a DC notification appliance circuit is to be

used, install a JP-D program plug into

receptacle P2 of the CP-35 control panel.

Note: If a battery charger/transfer module is

used, the program plug is not

necessary.

If an AC notification appliance circuit is to

be used, install a JP-A program plug into

receptacle P2 of the control panel.

Note: When a JP-A program plug is used, an

EL-32 end of line device is required for

the notification appliance circuit.

6. Wire the circuits as described in the MODEL

CP-35 CONTROL PANEL INSTALLATION

AND MAINTENANCE INSTRUCTIONS, P/N

315-085063 and the CP-35 WIRING DIAGRAM,

P/N 315-084902. The maximum line resistance

should be 3 ohms, and a minimum of 14 AWG

wire is recommended. All wiring should comply

with the local and national codes that apply to

the particular installation.

Operational Test

Refer to INSTALLATION AND WIRING in the

Instruction Manual (P/N 315-085063) for the

control panel.

Troubleshooting

Refer to TROU LESHOOTING THE CP-35 in the

Instruction Manual for the control panel.

Siemens Building Technologies, Inc.

8 Fe nwood Road

Flo ham Pa k, New Je sey 07932

Siemens Building Technologies, Ltd.

2 Kenview Bouleva d

B ampton, Onta io L6T 5E4 CN

P/N 315-085099-16

NOTES:

1. When emergency power is provided using

charger/ transfer module, Model C-35, 24 VDC

notification appliances must be used with EOL

device, Model EL-31. When C-35 is not used,

120 VAC notification appliances may be

employed by use of AC program plug, Model

JP-A, in P2 of CP-35 and Model EL-32 EOL

device, or by use of 24 VDC notification

appliances with DC program plug, Model

JP-D, in P2 and Model EL-31 EOL device.

2. Notification appliance circuits may be

activated from the silenceable system alarm

output signal, terminal 36 of CP-35, or from the

non-silenceable system alarm output signal,

terminal 42 of CP-35. When other alarm signals

such as coding or time delay/limit are required,

see individual module connection diagrams.

3. Use only the compatible polarized notification

appliances listed in P/N 315-096363.

4. To use power limited wiring to NFPA 70, NEC

Article 760, the notification appliance circuits

(terminals 3 and 4) must use the PLM-35

module. Refer to Instructions P/N 315-093495.

NOTE:

Refer to the BI-35 Installation

Instructions, P/N 315-086257,

for detailed wiring information

when using the AE-30U in

conjunction with the BI-35

module.

ACTUATION

INPUT

POLARIZEDNOTIFICATION

APPLIANCES (SEE NOTE 3)

END OF LINE DEVICE

(SEE NOTE 1)

CP-35

(SEE NOTE 2)

3 OHMS MAX TOTAL LINE

RESISTANCE OF NOTIFICATION

APPLIANCE CIRCUIT

CONNECTING WIRES

INPUT POWER

(SEE NOTE 1)

CP-35

STYLE Y (CLASS B)

CONNECTED

POLARIZED

NOTIFICATION

APPLIANCES

POLARITY SHOWN IN

SUPERVISORYCONDITION:

SUPV 24 VDC, 5mA

ALARM 24 VDC or 120 VAC,

1.5A MAX

Table des matières

Autres manuels Siemens Unité de contrôle

Siemens

Siemens SITRANS F M MAG 8000 Manuel utilisateur

Siemens

Siemens MC35 Terminal Manuel utilisateur

Siemens

Siemens SIRIUS Manuel utilisateur

Siemens

Siemens SIMATIC ET 200S Manuel utilisateur

Siemens

Siemens RVD240 Manuel de l'opérateur

Siemens

Siemens RUGGEDCOM RS900F Manuel utilisateur

Siemens

Siemens 3VL92 Series Manuel utilisateur

Siemens

Siemens 3VL9800-3MJ00 Manuel utilisateur

Siemens

Siemens 3TK2811 Manuel utilisateur

Siemens

Siemens Climatix POL822 Manuel utilisateur

Siemens

Siemens FCM-6S Manuel utilisateur

Siemens

Siemens SIRIUS 3RW44 Manuel utilisateur

Siemens

Siemens SINUMERIK 840Di Manuel utilisateur

Siemens

Siemens SMF6120 Manuel utilisateur

Siemens

Siemens HCP Manuel utilisateur

Siemens

Siemens Simatic S7-1500 Manuel utilisateur

Siemens

Siemens SIRIUS 3RA2130-4 A3 Series Manuel utilisateur

Siemens

Siemens SITRANS LU SAM Manuel utilisateur

Siemens

Siemens ACVATIX PS53 Manuel utilisateur

Siemens

Siemens SINUMERIK 828D Turning Manuel utilisateur

Siemens

Siemens SIMATIC 8DO DC24V/0.5 A Manuel utilisateur

Siemens

Siemens SINUMERIK 840D sl Manuel de la liste des pièces

Siemens

Siemens ST950 Manuel utilisateur

Siemens

Siemens SINUMERIK MC Guide de démarrage rapide

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur