Siemens SINAUT ST7 Guide de l'utilisateur

___________________

SIMATIC NET

Industrial Remote Communication -

TeleControl

SINAUT ST7 - Volume 1

System Manual

Volume 1: System and Hardware

11/2018

C79000

-G8976-C178-12

Preface

The SINAUT ST7 system

Properties of the TIM

modules

Network structures,

configuration examples,

installation guidelines

Installation, connecting up,

commissioning

Technical specifications

Certifications and approvals

Accessories

References

Siemens AG

Division Process Industries and Drives

Postfach 48 48

90026 NÜRNBERG

GERMANY

C79000-G8976-C178-12

Ⓟ

11/2018 Subject to change

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by

personnel qualified

for the specific

task in accordance with the relevant documentation, in particular its warning notices and safety instructions.

Qualified personnel are those who, based on their training and experience, are capable of identifying risks and

avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended

or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication

may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

SINAUT ST7 - Volume 1

System Manual, 11/2018, C79000-G8976-C178-12 3

Preface

Validity of the manual

This manual is valid for the following Ethernet TIM modules:

●

TIM 3V-IE

Article number 6NH7800-3BA00

●

TIM 3V-IE Advanced

Article number 6NH7800-3CA00

●

TIM 4R-IE

Article number 6NH7800-4BA00

Hardware revision level 4

Firmware version V2.7

Communication module for SIMATIC S7-300 and S7-400, SINAUT ST7 protocol

For the required software versions, see the "Software requirements" section.

Article number, hardware revision level and MAC addresses are engraved on the enclosure.

Figure 1 SIMATIC S7-300 with TIM 3V-IE Advanced (left) and TIM 4R-IE (right)

The following communication modules of the SINAUT ST7 telecontrol system are not

described in this system manual:

●TIM 1531 IRC

●CP 1243-8 IRC

●CP 1542SP-1 IRC

●RTU3000

Links to the manuals of these modules can be found in the bibliography in the appendix.

There you will also find links to the manuals of the SINAUT ST7cc and SINAUT ST7sc

control center systems.

Preface

SINAUT ST7 - Volume 1

4System Manual, 11/2018, C79000-G8976-C178-12

Purpose of the manual

This system manual describes the properties of the TIM modules listed above. It shows

application examples and supports you in installation, connection, commissioning,

configuration and diagnostics of the devices.

New in this release

●New structure of the documentation

New configuration manuals are being introduced for the telecontrol protocols DNP3 and

IEC 60870-5-101/104.

●New software versions

–Configuration with STEP 7 Professional V15.1

–New TD7onTIM typicals in the data point configuration of STEP 7 Professional V15.1

–New version of the TD7 block library Telecontrol ST7 V3.0 SP1 with new typicals

For details, see system manual Volume 3

Replaced documentation

This manual replaces the manual edition 02/2018.

Structure of the system manual

The SINAUT ST7 System Manual is divided into three volumes.

●

Volume 1: System & Hardware

Volume 1 introduces you to the SINAUT ST7 station control system and gives you an

overview of the current hardware components.

You will be supported during the planning of network structures and topologies and will

see how to install and commission SINAUT components based on the installation

guidelines.

In the foreword of Volume 1, you can also find an overview of discontinued products of

the SINAUT family with the corresponding editions of this system manual.

●

Volume 2 - Configuration under STEP 7 V5

Configuration and diagnostics of the TIM modules specified above in STEP 7 V5.

●

Volume 3 - Configuration under STEP 7 Professional (TIA Portal)

Configuration and diagnostics of all ST7-capable communications modules in

STEP 7 Professional.

Current manual release on the Internet

You can find the current version of this manual on the Internet pages of Siemens Industry

Online Support:

Link: (https://support.industry.siemens.com/cs/ww/en/ps/21771/man)

For older releases of the manual, see below, section Version history (Page 9).

Preface

SINAUT ST7 - Volume 1

System Manual, 11/2018, C79000-G8976-C178-12 5

Further information on the Internet

You can find additional information on the telecontrol products on the Internet at the following

address:

Link: (https://support.industry.siemens.com/cs/ww/en/ps/15915)

There, select the required information under "Entry type".

Sources of information and other documentation

You can find an overview of further reading and references in the Appendix of this manual.

Product names and abbreviations

●

TIM / module / Module / Device

The names are used for all three TIM versions.

●

STEP 7

The product name is used in the respective context for the configuration tool STEP 7 V5

or STEP 7 Professional.

●

Programming device, PC with the STEP 7 V5 project.

●

Engineering station, PC with the STEP 7 Professional project.

Cross references

In this manual there are often cross references to other sections.

To be able to return to the initial page after jumping to a cross reference, some PDF readers

support the command <Alt>+<left arrow>.

Software requirements

The following software versions are required (alternatively) for configuration and online

functions of the TIM modules described in this document:

●

STEP 7 V5

Required software:

–STEP 7 V5.6

together with

–SINAUT engineering software V5.5 + SP3

For TD7onCPU:

–When using TD7onCPU, the SINAUT TD7 library for the V2.2 + SP4 + HF1 CPU must

also be installed along with the SINAUT engineering software.

You can find the description of the configuration in Volume 2 of the system manual.

Preface

SINAUT ST7 - Volume 1

6System Manual, 11/2018, C79000-G8976-C178-12

●

STEP 7 Professional (TIA Portal)

Required software:

–STEP 7 Professional V15.1

Configuration with limited functions is possible with the following versions:

STEP 7 Professional V14.0 SP1 Update 1

STEP 7 Professional V15

For TD7onCPU:

–You can download the associated SINAUT TD7 library V3.0 for the CPU, which can

be used for STEP 7 Professional version V15 or later, from the Web pages of

Siemens Industry Online Support:

Link: (https://support.industry.siemens.com/cs/ww/en/view/109755374)

You can find the description of the configuration in Volume 3 of the system manual.

Compatible CPUs

You can find the CPU types, which can be used together with the respective TIM module, in

the section Installation guidelines and compatible CPUs (Page 61).

Security information

Siemens provides products and solutions with industrial security functions that support the

secure operation of plants, systems, machines and networks.

In order to protect plants, systems, machines and networks against cyber threats, it is

necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial

security concept. Siemens’ products and solutions constitute one element of such a concept.

Customers are responsible for preventing unauthorized access to their plants, systems,

machines and networks. Such systems, machines and components should only be

connected to an enterprise network or the internet if and to the extent such a connection is

necessary and only when appropriate security measures (e.g. firewalls and/or network

segmentation) are in place.

For additional information on industrial security measures that may be implemented, please

visit

Link: (http://www.siemens.com/industrialsecurity)

Siemens’ products and solutions undergo continuous development to make them more

secure. Siemens strongly recommends that product updates are applied as soon as they are

available and that the latest product versions are used. Use of product versions that are no

longer supported, and failure to apply the latest updates may increase customers’ exposure

to cyber threats.

To stay informed about product updates, subscribe to the Siemens Industrial Security RSS

Feed under

Link: (http://www.siemens.com/industrialsecurity)

Preface

SINAUT ST7 - Volume 1

System Manual, 11/2018, C79000-G8976-C178-12 7

License conditions

Note

Open source software

Read the license conditions for open source software carefully before using the product.

You will find license conditions in the following documents on the supplied data medium:

●OSS_TIM-3VIE_99.pdf

●OSS_TIM-4RIE_99.pdf

●OSS_SINAUT-ES_99.pdf

Discontinued products

Note

Discontinuation of modules (product discontinuation)

Note the following products to be discontinued.

If there are successors to the discontinued devices, you can find these in the notifications on

the Internet.

●The following products have the status "Type discontinuation" as of 15 April 2015:

–TIM 4R (6NH7800-4AA90)

–TIM 4RD (6NH7800-4AD90)

Read the product notifications about this on the Internet:

Link: (https://support.industry.siemens.com/cs/ww/en/view/109475169)

●The following products have the status "Type discontinuation" as of 1 October 2016:

–Modem MD2

–Modem MD3

–LTOP1 / LTOP2 and accessories

Read the product notifications about this on the Internet:

Link: (https://support.industry.siemens.com/cs/ww/en/view/109740147)

–EGPRS router MD741-1

Read the product notifications about this on the Internet:

Link: (https://support.industry.siemens.com/cs/ww/en/view/62607452)

Documentation 09/2016 for TIM 4R / TIM 4RD and accessories

This edition of the system manual no longer contains information on the TIM 4R and

TIM 4RD modules.

Preface

SINAUT ST7 - Volume 1

8System Manual, 11/2018, C79000-G8976-C178-12

For information on these products, refer to the 09/2016 edition of the system manual, which

is available on the Siemens Industry Online Support website:

●Volume 1

Link: (https://support.industry.siemens.com/cs/ww/en/view/109745599)

●Volume 2

Link: (https://support.industry.siemens.com/cs/ww/en/view/109748055)

Documentation 05/2007 for SINAUT ST1 and older ST7 modules

This edition of the system manual no longer contains information on the SINAUT ST1

system and the following older modules:

●All previous TIM 3 modules: TIM 3V, TIM 32, TIM 33, TIM 34

●TIM 4V, TIM 4VD, TIM 42, TIM 42D, TIM 43, TIM 43D, TIM 44, TIM 44D

If you require information on these modules or on SINAUT ST1, refer to Edition 05/2007 of

this manual, which you can find on the website of Siemens Industry Online Support:

●Volume 1

Link: (https://support.industry.siemens.com/cs/ww/en/view/24621696)

●Volume 2

Link: (https://support.industry.siemens.com/cs/ww/en/view/63112659)

You can find an overview of the products in the section Hardware components (Page 18).

Recycling and disposal

The product is low in pollutants, can be recycled and meets the requirements of the WEEE

directive 2012/19/EU "Waste Electrical and Electronic Equipment".

Do not dispose of the product at public disposal sites. For environmentally friendly recycling

and the disposal of your old device contact a certified disposal company for electronic scrap

or your Siemens contact.

Keep to the local regulations.

You will find information on returning the product on the Internet pages of Siemens Industry

Online Support:

Link: (https://support.industry.siemens.com/cs/ww/en/view/109479891)

SIMATIC NET glossary

Explanations of many of the specialist terms used in this documentation can be found in the

SIMATIC NET glossary.

You will find the SIMATIC NET glossary here:

●SIMATIC NET Manual Collection or product DVD

The DVD ships with certain SIMATIC NET products.

Preface

SINAUT ST7 - Volume 1

System Manual, 11/2018, C79000-G8976-C178-12 9

●On the Internet under the following address:

Link: (https://support.industry.siemens.com/cs/ww/en/view/50305045)

A SINAUT-specific glossary can be found in the appendix of this manual.

Training, Service & Support

You will find information on training, service and support in the multilanguage document

"DC_support_99.pdf" on the Internet pages of Siemens Industry Online Support:

Link: (https://support.industry.siemens.com/cs/ww/en/view/38652101)

Version history

The previous versions of the manual described the innovations and versions listed below.

Edition 02/2018 of the manual (C79000-G89xx-Cxxx-10)

New functions:

●

Documentation

Volume 3 has been added to the system manual to describe the configuration in

STEP 7 Professional (TIA Portal).

●

Configuration in STEP 7 Professional

The Ethernet TIM modules can be configured as of firmware version V2.6 in STEP 7

Professional (TIA Portal).

Configuration is supported as of STEP 7 Professional V15.

●

SINAUT Engineering Software

New functions of the SINAUT engineering software in the version specified below

("Software requirements" section), including:

Configuration of proxy modules for the transfer of the configuration data to

STEP 7 Professional projects:

–PROXY CP1243-8 IRC based on a TIM 3V-IE Advanced

–PROXY TIM 1531 IRC based on a TIM 4R-IE

Support of Windows 10 / Server 2012 / Server 2016

●

Block library TD7onCPU for

STEP 7 Professional

The TD7onCPU programming blocks are available for STEP 7 Professional V15 in the

library version V3.

●

TIM firmware

The new functions are supported as of firmware version V2.6.

Preface

SINAUT ST7 - Volume 1

10 System Manual, 11/2018, C79000-G8976-C178-12

Edition 09/2016 of the manual (C79000-G89xx-Cxxx-10)

New functions:

●

Engineering software

New version of the SINAUT engineering software V5.5 SP2, can be used under STEP 7

as of version V5.4 SP4:

–Configuration of a PROXY CP1243-8 IRC module based on a TIM 3V-IE Advanced

The 1243-8 IRC can be configured in STEP 7 Basic as of version V13.0 SP1.

–Improvement of the selective connection configuration by selecting individual

subscribers

–Passing of the key exchange interval to the MODEM MD720 when using the MSCsec

protocol

–Errors corrected in the time-of-day synchronization of a TIM by the CPU

●

Block library TD7onCPU

New version of the block library TD7onCPU V2.2 SP4 + Hotfix 1

–New block "FC-PathStatus" to display the main and substitute path to the remote

communications partner.

The block can be used as of version V5.5 SP1 of the engineering software and as of

TIM firmware V2.5.4.

–The block library can now be used both in a standalone TIM in an S7-400 and an S7-

400H also with only one single CPU (single mode).

Validity of the manual:

●TIM 3V-IE, TIM 3V-IE Advanced, TIM 4R-IE, TIM 4R / 4RD

●SINAUT ST7 configuration and diagnostics software for the PG V5.4

●SINAUT TD7 library for the CPU V2.2 SP2

●SINAUT TIM firmware V4.4.0 for the TIM 4

●SINAUT TIM firmware V2.5 for the TIM 3V-IE variants

●SINAUT TIM firmware V2.5 for the TIM 4R-IE

The new functions of the SINAUT engineering software V5.5 SP2 mentioned above are

supported by firmware version V2.5.4 of the Ethernet TIM modules.

Autres manuels pour SINAUT ST7

Table des matières

Autres manuels Siemens Système de contrôle

Siemens

Siemens QAX850 Manuel utilisateur

Siemens

Siemens Desigo TRA Manuel utilisateur

Siemens

Siemens QAX850 Manuel utilisateur

Siemens

Siemens SINUMERIK 828D PPU Series Manuel utilisateur

Siemens

Siemens PCS 7 Manuel utilisateur

Siemens

Siemens SIMATIC PCS 7 Manuel de la liste des pièces

Siemens

Siemens SIMATIC PCS 7 OSx Manuel utilisateur

Siemens

Siemens SINUMERIK 840DE SL Guide de démarrage rapide

Siemens

Siemens SIDOOR ATD401W Guide de l'utilisateur

Siemens

Siemens SIMATIC PCS 7 Manuel utilisateur

Siemens

Siemens SIMATIC PCS 7 Manuel de la liste des pièces

Siemens

Siemens SINUMERIK 840DE SL Manuel utilisateur

Siemens

Siemens SINUMERIK 840D sl Guide de démarrage rapide

Siemens

Siemens SINUMERIK 802S Manuel d'installation

Siemens

Siemens SIMATIC PCS 7 Guide de l'utilisateur

Siemens

Siemens SINUMERIK 840D sl Manuel de la liste des pièces

Siemens

Siemens SINUMERIK 840D sl Manuel utilisateur

Siemens

Siemens LMV 5 Series Manuel utilisateur

Siemens

Siemens SINUMERIK 840D sl Manuel du propriétaire

Siemens

Siemens RRV851 Manuel utilisateur

Siemens

Siemens SINUMERIK 802S Guide de configuration

Siemens

Siemens SINUMERIK ONE MCP 2400.c Document technique

Siemens

Siemens SINUMERIK 840D Manuel

Siemens

Siemens SIRIUS 3SB1 Series Manuel utilisateur

Manuels Système de contrôle populaires d'autres marques

Pentair Pool Products

Pentair Pool Products Compool Manuel utilisateur

ComfortNET

ComfortNET CTK04 Manuel utilisateur

Fireye

Fireye InSight II 95DSS3 Manuel utilisateur

CAME

CAME G3000 Manuel utilisateur

Idemia

Idemia MorphoAccess VP MD Manuel utilisateur

Axis

Axis P1445-LE-3 Manuel utilisateur

HEIDENHAIN

HEIDENHAIN TNC 150 B Manuel utilisateur

CNC-Step

CNC-Step High-Z T-Series Manuel utilisateur

Doosan

Doosan DVF Series Manuel utilisateur

Honeywell

Honeywell KAP 140 Manuel utilisateur

Honeywell

Honeywell vk41 series Manuel utilisateur

AirBench

AirBench FPW Guide d'installation

Cypress

Cypress HHR-3160 Manuel utilisateur

CAME

CAME GLT40AOS Manuel utilisateur

Zonex

Zonex GEN II -VVT Guide de l'utilisateur

Altronics

Altronics K 9650 Manuel utilisateur

micro-trak

micro-trak RoadMaster Manuel utilisateur

micro-trak

micro-trak Calc-An-Acre II Manuel utilisateur