Siemens SIJECT15 Manuel utilisateur

SIJECT15/16

Operation Manual

Software Version 1

User Manual 06.2003 Edition

User Documentation

User Manual: Operator Manual

SINUMERIK

802S

SIJECT 15/16 Document Structure

SINUMERIK

802S

Technical Manual: Start-Up

SINUMERIK

802S

General Documentation:

Ctl

Short

Guide for

Start-up

Operation

Manual

Start-up

Valid for

Control System Software Version

SIJECT 15/16 1.08

06.2003 Edition

SIJECT 15/16

Operation Manual

Software Version 1

User Manual

Introduction

Operator panel keys

SIJECT OP15B Screen

SIJECT® Documentation

Key to editions

The editions listed below have been published prior to the current edition.

The column headed "Note" lists the amended sections, with reference to the previous edition.

Marking of edition in the "Note" column:

A .... New documentation.

B .... Unchanged reprint with new order number

C .... Revised edition of new issue.

If any technical details presented on one of these pages have been changed with reference to

the previous edition, it is indicated by another edition number in the header of the respective

page.

Edition

12.2000

06.2001

07.2002

06.2003

Order No.

6AT1931-5AB41-0KA0

6AT1931-5AB41-0KA1

Remark

Tested Siemens quality for software and training to

DIN ISO 9001, Reg. No. 2160-01

This publication was made with WinWord V 7

and Designer V 6.0

Passing on and reproduction of this document, and utilization and disclosure of its

contents is not allowed unless specifically authorized.

event a patent is issued or a utility model patent is registered.

Other functions which are not described in this Documentation can possibly also

be performed on the control system. However, the customer is not entitled to

demand these functions when new equipment is supplied or servicing is carried

out.

Although we have checked the contents of this publication for agreement with the

hardware and software described, we do not accept liability for total agreement

since differences cannot be totally ruled out. The information in this publication is

checked at regular intervals and necessary correction included in the next release.

Suggestions are welcome.

Subject to change without prior notice.

Order No.

Printed in People’s Republic of China

Siemens-Aktiengesellschaft.

Table of Content

1 Introduction .................................................................................................. 1-1

1.1 Operating panel layout ......................................................................... 1-2

1.2 Overview of screens............................................................................. 1-4

1.3 Working process of injection molding machine.................................... 1-6

2 Operator panel keys .................................................................................... 2-1

2.1 Liquid crystal display (LCD) ................................................................. 2-2

2.2 Soft keys............................................................................................... 2-3

2.3 Screen hot keys.................................................................................... 2-6

2.4 Manual Operating Keys........................................................................ 2-8

2.5 Number Keys...................................................................................... 2-11

2.6 Cursor Keys........................................................................................ 2-11

2.7 Operating mode keys ......................................................................... 2-12

2.8 Motor keys and Heater keys .............................................................. 2-15

3 SIJECT OP15B Screens ............................................................................. 3-1

3.1 Hot key Screens ................................................................................... 3-2

3.1.1 Information Screen 3-9

3.1.2 Monitoring screen 3-12

3.1.3 Alarm screen 3-14

3.1.4 Temperature screen 3-16

3.1.5 Timer screen 3-17

3.1.6 Counter screen 3-19

3.1.7 Function screen 3-20

3.1.8 Save/load screen 3-22

3.1.9 Data screen 3-24

3.1.10 Service screen 3-26

3.2 Manual operation screen.................................................................... 3-38

3.2.1 Mold open/close screen 3-38

3.2.2 Ejector screen 3-40

3.2.3 Carriage Screen 3-42

3.2.4 Injection screen 3-43

3.2.5 Charging screen 3-45

3.2.6 Core 1 screen 3-47

3.2.7 Core 2 screen 3-50

3.2.8 Air blow screen 3-52

3.2.9 Mold adjustment screen 3-53

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Siemens Système de contrôle

Siemens

Siemens RVW26.000B27 Manuel de l'opérateur

Siemens

Siemens SIMATIC PCS 7 BOX Manuel utilisateur

Siemens

Siemens SIPLUS HCS Guide de l'administrateur

Siemens

Siemens SINUMERIK ONE MCP 2400.4c Document technique

Siemens

Siemens SINUMERIK 828D Turning Manuel de la liste des pièces

Siemens

Siemens SIRIUS 3SB1 Series Manuel utilisateur

Siemens

Siemens simatic c7-621 Manuel utilisateur

Siemens

Siemens SINUMERIK 840D sl Manuel de la liste des pièces

Siemens

Siemens simatic c7-621 Manuel utilisateur

Siemens

Siemens SIMATIC PCS 7 Manuel de la liste des pièces

Siemens

Siemens QAW10 Manuel utilisateur

Siemens

Siemens SIMATIC C7-635 Manuel utilisateur

Siemens

Siemens SINUMERIK ONE NCU 1740 Document technique

Siemens

Siemens SINUMERIK 840D sl Manuel utilisateur

Siemens

Siemens SIMATIC PCS 7 Manuel utilisateur

Siemens

Siemens SIMATIC PCS 7 Manuel utilisateur

Siemens

Siemens SIPLUS HCS3200 Manuel utilisateur

Siemens

Siemens SIMATIC PCS 7 Feuille d'instructions

Siemens

Siemens sitrans LU10 Manuel utilisateur

Siemens

Siemens SINUMERIK Manuel du propriétaire

Siemens

Siemens TXP-CLC Manuel utilisateur

Siemens

Siemens SINUMERIK 808D Manuel utilisateur

Siemens

Siemens SINUMERIK 840D sl Guide de démarrage rapide

Siemens

Siemens SIPLUS HCS Series Manuel utilisateur

Manuels Système de contrôle populaires d'autres marques

Pentair Pool Products

Pentair Pool Products Compool Manuel utilisateur

ComfortNET

ComfortNET CTK04 Manuel utilisateur

Fireye

Fireye InSight II 95DSS3 Manuel utilisateur

CAME

CAME G3000 Manuel utilisateur

Idemia

Idemia MorphoAccess VP MD Manuel utilisateur

Axis

Axis P1445-LE-3 Manuel utilisateur

HEIDENHAIN

HEIDENHAIN TNC 150 B Manuel utilisateur

CNC-Step

CNC-Step High-Z T-Series Manuel utilisateur

Doosan

Doosan DVF Series Manuel utilisateur

Honeywell

Honeywell KAP 140 Manuel utilisateur

Honeywell

Honeywell vk41 series Manuel utilisateur

AirBench

AirBench FPW Guide d'installation

Cypress

Cypress HHR-3160 Manuel utilisateur

CAME

CAME GLT40AOS Manuel utilisateur

Zonex

Zonex GEN II -VVT Guide de l'utilisateur

Altronics

Altronics K 9650 Manuel utilisateur

micro-trak

micro-trak RoadMaster Manuel utilisateur

micro-trak

micro-trak Calc-An-Acre II Manuel utilisateur