Shuttle AE23 Manuel utilisateur

RAID Administrator

User's Manual

M483

40-012-A87121

- 1 -

Chapter 1

Getting Started..........................................................................................................3

1-1 Introduction ...................................................................................................3

1-2 Main Features & Benefits..............................................................................3

Chapter 2

Installation of Driver .................................................................................................4

2-1 Windows 98/ME............................................................................................4

2-2 WindowsNT4.0 ............................................................................................6

2-3 Windows 2000..............................................................................................7

2-4 Windows XP.................................................................................................9

Chapter 3

Use RAID Administrator .........................................................................................12

3-1 InstallRAIDAdministrator............................................................................13

3-2 Run RAIDAdministrator ..............................................................................13

3-3 Create Stripe Array.....................................................................................15

3-4 Create Mirror Array .....................................................................................17

3-5 Add/Remove Spare Disk ............................................................................18

3-6 Synchronize/Validate/VerifyMirrorArray......................................................19

3-7 Create Span Array......................................................................................21

3-8 Create 0+1 Array ........................................................................................22

3-9 Remove Disk Array.....................................................................................23

3-10 SetTransferMode ....................................................................................24

3-11 Device Status............................................................................................25

3-12 Hot-swapping Hard Disks of Mirror Array ..................................................26

3-13 Event Log .................................................................................................27

TABLE OF CONTENTS

- 2 -

Chapter 4

BIOS Configuration ................................................................................................28

4-1 Enter into BIOSConfigurationUtility ............................................................29

4-2 Create RAID ...............................................................................................30

4-3 Delete RAID............................................................................................... 31

4-4 RebuildMirrorArray....................................................................................31

4-5 Add Spare Disk......................................................................................... 32

4-6 Remove Spare Disk ...................................................................................32

4-7 Set Disk Mode............................................................................................32

4-8 Set Boot Disk .............................................................................................33

- 3 -

************************************************

1.1 Introduction

1.2 Main Features & Benefits

************************************************

1.1 Introduction

HPT372 is UDMA/ATA133 RAID controller.

RAID Administrator is a Windows- ased RAID management utility for

HPT372 RAID Controller. With graphical user interface, RAID Administrator

ena le users easily configure and manage disk and disk arrays connected to

HPT372 RAID controller.

1.2 Main Features & Benefits

Below are the main features and enefits of RAID Administrator.

(1) Support RAID 0, 1,0+1 & JBOD

(2) Allowed maximum 4 disks connection to every controller

(3) Hot-swapping failed hard disk in mirror array

(4) Support independent use of hard disk

(5) Support hot spare disk

(6) Support Operating Systems: DOS/Windows 3.x, Windows98/Me,

Windows NT4.0, Windows 2000, Windows XP and Linux.

(7) Windows- ased software for RAID management(compati le with

BIOS)

(8) Disk error alarm mechanism

(9) Event log for easy trou le shooting

(10) Plug-and-play

GETTING STARTED Chapter 1

- 4 -

INSTALLATIONOFDRIVER

Chapter 2

************************************************

This chapter will guide user to install drivers for HPT372 RAID controller. Contents

include:

2.1 Windows 98/Me

2.2 Windows NT4.0

2.3 Windows 2000

2.4 Windows XP

************************************************

2.1 Windows 98/Me

6Automatic Installation

After the computer start-up, Windows system will find the newly installed

RAID adapter and ask you to install its driver. Please follow the prompt to

finish the driver installation.

6Manual Installation

If Windows can not find new hardware, the driver can e installed through the

following steps :

1. Shut down all programs.

2. Click Start-->Setup-->Control Panel, then dou le-click on Add

New Hardware icon.

3. Click Next in the popup window to continue.

4. A dialog ox will appear and ask whether to let windows search new

hardware. Select No,I want to select the hardware form a list. and

then click Next to continue.

5. Hardwares of different types will e shown in the follow-on window.

Select SCSI Controllers and then click Next to continue.

6. Insert the CD disk of driver into the CD-ROM drive, then click Ha e

Disk....

- 5 -

7. A dialog ox will pop up, input the path of drive D:\RAID\Win9X.

Then click OK to continue.

8. In the follow-on window, driver will list out the controller type you

need to install, please just click Next to continue.

9. Follow the system prompt to install driver. When finished, restart

the computer.

6Verify Installation

When the driver has een successfully installed and the computer restarted:

1. Right-click My Computer icon on desktop, and then select Property

item from the popup menu.

2. Select De ice Manager item from the popup window.

If there is HPT372 items under SCSI Controllers, it indicates that the

driver has een installed properly.

If you cannot find these two a ove-mentioned device items,or there are ? or !

on device icon, it indicates that the driver has not een correctly installed

and needs reinstallation.

- 6 -

2.2 Windows NT4.0

6Install driver under Windows NT4.0

1. Click Start -->Setup -->Control Panel, then dou le-click SCSI

Adapter icon.

2. In the follow-on window, select Dri er item. then click Add utton.

3. In the follow-on window, select Ha e Disk....

4. Insert the CD disk of driver, input the path of driver D:\RAID\WinNT,

then click OK.

5. In the follow-on window, select HPT372 UDMA/ATA133 RAID

Controller item, then click OK.

6. Follow the system prompt to install the driver. When finished, restart

the computer.

6Install driver in the process of Windows NT4.0 installation

1. Press F6 key when the system prompts Setup is inspecting your

computers hardware configuration.

2. Press F6 key, the installation will continue. Later, installation pro-

gram will remind user to press S key to specify other devices. Please

press S key.

3. In the follow-on De ice Type window, select Other item, then

press Enter to confirm.

4. The installation program will prompt users to insert the CD disk

of driver. Please insert it and then press Enter to confirm.

5. In the follow-on window, select HPT372 UDMA/ATA133 RAID

Controller, then press Enter to confirm.

6. The follow-on interface will list the devices to e installed, in which

HPT372 UDMA/ATA133 RAID Controller item should e included.(

If users want to install other devices,please operate at this time. If all

devices have een successfully installed, please go to next.)

7. Press Enter to continue the installation of Windows NT4.0.

6Verify Installation

When the driver has een successfully installed and the computer restarted:

1. Click Start -->Setup -->Control Panel, and then dou le-click SCSI

Adapter item.

- 7 -

2. If there is HPT372 UDMA/ATA133 RAID Controller item in the

popup window, it indicates that the driver has een successfully

installed. Otherwise, users need to reinstall the driver.

2.3 Windows 2000

6Install driver under Windows 2000

Automatic Installation

Start the computer and enter the operating system of Windows 2000,

the system will automatically detect new hardware and prompt users to

install the driver. Please insert the CD disk of driver and follow the

system prompt to finish the driver installation and restart the computer.

Manual Installation

If Windows can not find new hardware, the driver shall e installed

through the following steps :

1. Click Start -->Setup -->Control Panel, select Add/Remo e New

Hardware. In the follow-on window, Click Next to continue.

2. In the follow-on window, select the first item Add/Troubleshoot a

de ice, then click Next to continue.

3. In the follow-on device list, select the first item Add New De ice,

then click Next to continue.

- 8 -

4. Then the system will ask Did you want Windows to search for

your new hardware? Please select No, I want to select the hardware

from a list. then click Next to continue.

5. In the follow-on window of device types, select SCSI and RAID

controllers, then click Next to continue.

6. In the follow-on window, select Ha e Disk....

7. Please insert the CD disk of driver and input path name

D:\RAID\Win2k into Copy manufacturers files from: column, then

click OK.

8. In the follow-on type column, select HPT372 UDMA/ATA133 RAID

Controllers.

9. Follow the system prompt to finish the installation, and restart the

computer.

6Install driver in the process of Windows 2000 installation

1. If Windows 2000 is installed from the CD-ROM drive, please F6 key

when the message Press F6 if you need to install third party SCSI or

RAID dri er appears. If it is to type Winnt and install, after files have

een copied and the computer restarted, press F6 key when the

message Setup is inspecting your computers hardware configura-

tion appears.

2. Press S key to specify additional devices when the Windows 2000

Setup window appears.

3. In the follow-on window of device type, please select Other and

press Enter to continue.

4. Insert the CD disk of driver, then press Enter to continue.

5. The system will ask whether to install driver under WinNT or under

Windows 2000, please select to install driver under Windows 2000.

6. The follow-on interface will list the devices to e installed, in which

HPT372 UDMA/ATA133 RAID Controller item should e included.(

If users want to install other devices,please operate at this time. If all

devices have een successfully installed, please go to next.)

7. Press Enter to continue Windows 2000 setup.

- 9 -

6Verify Installation

When the driver has een successfully installed and the computer restarted:

1. Right-click My Computer icon, select Property item in the popup menu.

2. In the popup window, select Hardware item and then click De ice

Manager utton.

If there is HPT372 UDMA/ATA133 RAID Controller item in the popup

De ice Manager window, it indicates that the driver has een successfully

installed. Otherwise, please reinstall the driver.

2.4 Windows XP

6Install driver under Windows XP

Automatic Installation

Start the computer and enter the operating system of Windows XP, the

system will automatically detect new hardware and prompt users to

install the driver. Please insert the CD disk of driver and follow the

system prompt to finish the driver installation and restart the computer.

Manual Installation

If Windows can not find new hardware, the driver shall e installed

through the following steps :

Table des matières

Autres manuels Shuttle Carte mère

Shuttle

Shuttle FS51 Manuel utilisateur

Shuttle

Shuttle Spacewalker MS51 Manuel utilisateur

Shuttle

Shuttle MS11 Manuel utilisateur

Shuttle

Shuttle Spacewalker MV18 Manuel utilisateur

Shuttle

Shuttle AB60N Manuel utilisateur

Shuttle

Shuttle FN95 Manuel utilisateur

Shuttle

Shuttle AK32E Manuel utilisateur

Shuttle

Shuttle FB62 Manuel utilisateur

Shuttle

Shuttle AV49V Manuel utilisateur

Shuttle

Shuttle HOT-433 Manuel utilisateur

Shuttle

Shuttle FN45U Manuel utilisateur

Shuttle

Shuttle AV49 Manuel utilisateur

Shuttle

Shuttle AK32A Manuel utilisateur

Shuttle

Shuttle Spacewalker AB40 Manuel utilisateur

Shuttle

Shuttle MK35 Manuel utilisateur

Shuttle

Shuttle FB83 Manuel utilisateur

Shuttle

Shuttle AK12 Manuel utilisateur

Shuttle

Shuttle Spacewalker AK32 Manuel utilisateur

Shuttle

Shuttle AB61 Manuel utilisateur

Shuttle

Shuttle MN31 Manuel utilisateur

Shuttle

Shuttle HOT-597 Manuel utilisateur

Shuttle

Shuttle FN41 Manuel utilisateur

Shuttle

Shuttle FT62 Manuel utilisateur

Shuttle

Shuttle Spacewalker MV11 Manuel utilisateur

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur