Sharp AR-F15 Manuel utilisateur

CONTENTS

Parts marked with “ ” are important for maintaining the safety of the set. Be sure to replace these parts with

specified ones for maintaining the safety and performance of the set.

SHARP CORPORATION This document has been published to be used

for after sales service only.

The contents are subject to change without notice.

SERVICE MANUAL

CODE: 00ZARF16//A2E

DIGITAL COPIER/PRINTER/

MULTIFUNCTIONAL SYSTEM OPTION

FINISHER/PUNCH MODULE

AR-F15

AR-F16

MODEL AR-PN4

AR-F15

AR-PN4

AR-F16

CHAPTER 1 GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

CHAPTER 2 FINISHER UNIT BASIC OPERATION . . . . . . . . . . . . . . . . . . . . . 2-1

CHAPTER 3 SADDLE STITCH UNIT BASIC OPERATION . . . . . . . . . . . . . . . 3-1

CHAPTER 4 PUNCHER UNIT (OPTION) BASIC OPERATION . . . . . . . . . . . . 4-1

CHAPTER 5 MECHANICAL CONSTRUCTION. . . . . . . . . . . . . . . . . . . . . . . . . 5-1

CHAPTER 6 MAINTENANCE AND INSPECTION . . . . . . . . . . . . . . . . . . . . . . 6-1

CHAPTER 7 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

APPENDIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

NOTE: This manual is based on the AR-F11/F12/PN3 manuals.

The sections marked with or are different sections from the

AR-F11/F12/PN3 manuals.

F15/F16

PN4

General Precautions for Installation/Servicing/Maintenance for the Finisher

AR-F15/F16, Hole punch unit AR-PN4

The installation and service should be done by a qualified service technician.

When installing the Finisher AR-F15/F16, Hole punch unit AR-PN4 to the Plain Paper Copier,

be sure to follow the instructions described in the “Unpacking/Set-Up Procedure for the

AR-F15/F16/AR-PN4” booklet which comes with each unit of the AR-F15/F16/AR-PN4.

2. The AR-F15/F16, AR-PN4 should be installed by an authorized/qualified person.

3. Before starting installation, servicing or maintenance work, be sure to turn off and

unplug the copier first.

4. When selecting the installation site, avoid placing the AR-F15/F16 and copier on dif-

ferent levels or inclined floors.

5. When servicing or maintaining the AR-F15/F16/AR-PN4, be careful about the rotating

or operation sections such as gears, pulleys, sprockets, cams, belts, etc.

When parts are disassembled, reassembly is the reverse of disassembly unless other-

wise noted in this manual or other related materials. Be careful not to reassemble small

parts such as screws, washers, pins, E-rings, toothed washers to the wrong places.

7. Basically, the machine should not be operated with any parts removed or disassembled.

Delicate parts for preventing safety hazard problems (such as breakers,

thermofuses, fuses, door switches, sensors, etc. if any) should be handled/installed/

adjusted correctly.

9. Use suitable measuring instruments and tools.

10. During servicing or maintenance work, be sure to check the serial No. plate and other

cautionary labels (if any) to see if they are clean and firmly fixed. If not, take appropri-

ate actions.

11. The PC board must be stored in an anti-electrostatic bag and handled carefully using

a wristband, because the ICs on it may be damaged due to static electricity. Before

using the wrist band, pull out the power cord plug of the copier and make sure that

there is no uninsulated charged objects in the vicinity.

12. For the recovery and disposal of used AR-F15/F16/AR-PN4s, consumable parts, pack-

ing materials, used batteries, and RAM-ICs including lithium batteries, it is recom-

mended that the relevant local regulations/rules.

13. After completing installation, servicing and maintenance of the AR-F15/F16/AR-PN4,

return the AR-F15/F16/AR-PN4 to its original state, and check operation.

14. When you move the finisher, do not move it in the direction of the arrow as shown in

the figure below otherwise it might fall down.

INTRODUCTION

This Service Manual contains basic data and figures for the Finisher (AR-F15)/Saddle

Finisher (AR-F16) needed to service the machine in the field.

This manual comprises the following chapters:

Chapter 1 “General Description”introduces the finisher’s features, specifications, and

names of parts, and shows how to operate the finisher.

Chapter 2 “Finisher Unit Basic Operation”discusses the principles of operation used for

the finisher mechanical and electrical systems. It also explains the timing at

which these systems are operated.

Chapter 3 “Saddle Finisher Unit Basic Operation”discusses the principles of operation

used for the saddle stitch unit’s mechanical and electrical systems. It also

explains the timing at which these systems are operated.

Chapter 4 “Puncher (option) Unit Basic Operation”discusses the principles of operation

used for the puncher unit’s mechanical and electrical systems. It also explains

the timing at which these systems are operated.

Chapter 5 “Mechanical System”discusses how the finisher is constructed mechanically,

and shows how it may be disassembled/assembled and adjusted.

Chapter 6 “Maintenance and Inspection”provides tables of periodically replaced parts

and consumables and durables, together with a scheduled servicing chart.

Chapter 7 “Troubleshooting”shows how to troubleshoot possible faults and gives electri-

cal parts arrangement diagrams, LED/check pin diagrams by PCB, and self

diagnosis tables.

“Appendix”contains diagrams showing tables of signals, overall circuit dia-

grams and tables of solvents/oils.

Descriptions regarding installation are not mentioned in this Service Manual as the

Finisher (AR-F15)/Saddle Finisher (AR-F16)’s packing boxes contain Installation Proce-

dures.

The descriptions in this Service Manual are subject to change without notice for prod-

uct improvement or other purposes, and major changes will be communicated in the form

of Service Information bulletins.

All service persons are expected to have a good understanding of the contents of this

Service Manual and all relevant Service Information bulletins, and be able to identify and

isolate faults in the machine.

CHAPTER 1 GENERAL DESCRIPTION

CONTENTS

I. FEATURES ..................................1-1

II. SPECIFICATIONS .......................1-2

A. Finisher specifications

(AR-F15/F16) ...........................1-2

B. Punch unit specifications

(AR-PN4)..................................1-8

C. Engine specification

(AR-F15/F16/PN4) .................. 1-9

D. Cross Section .........................1-11

III. Using the Machine.....................1-14

A. Removing Paper Jams from the

Finisher Unit ...........................1-14

B. Supplying the Finisher Unit with

Staples ...................................1-15

C. Removing Staple Jams from the

Finisher Unit ...........................1-17

D. Removing Paper Jams from the

Saddle Stitch Unit

(Saddle Finisher) ....................1-18

E. Supplying the Saddle Stitch

Unit with Staples

(Saddle Finisher) ....................1-20

F. Removing Staple Jams from the

Saddle Stitch Unit

(Saddle Finisher) ....................1-21

G. Removing Paper Jams from the

Puncher Unit (option) .............1-23

H. Removing Punched Scrap from

the Puncher Unit (option) .......1-25

IV. MAINTENANCE BY THE

USER ........................................1-26

A. Maintenance by the User .......1-26

I. BASIC OPERATION ....................2-1

A. Outline......................................2-1

B. Outline of Electrical Circuitry ....2-2

C. Inputs to and Outputs from the

Finisher Controller PCB ...........2-4

II. FEED/DRIVE SYSTEM .............2-10

A. Outline....................................2-10

B. Type of Delivery Paths............2-15

C. Feeding and Delivering ..........2-18

D. Job Offset ...............................2-21

E. Staple Operation ....................2-24

F. Stapler Unit ............................2-32

G. Tray Operation ........................2-38

H. Detecting the Height of

Stack on the Tray ....................2-40

I. Shutter Operation...................2-42

J. Buffer Path Operation.............2-46

K. Detecting Jams ......................2-51

III. POWER SUPPLY SYSTEM.......2-56

CHAPTER 2 FINISHER UNIT BASIC OPERATION

iii

I. BASIC OPERATION ....................3-1

A. Outline......................................3-1

B. Electrical Circuitry ....................3-2

C. Inputs to and Outputs from the

Saddle Stitch Controller PCB ...3-3

II. FEEDING/DRIVE SYSTEM .........3-8

A. Outline......................................3-8

III. PAPER OUTPUT

MECHANISM.............................3-14

A. Outline....................................3-14

B. Controlling the Inlet

Flappers .................................3-17

C. Controlling the Movement of

Sheets ....................................3-21

D. Aligning the Sheets ................3-23

E. Controlling the Phase of the

Crescent Roller ......................3-26

IV. STITCHING SYSTEM ...............3-28

V. FOLDING/DELIVERY

SYSTEM....................................3-31

VI. CHECKING FOR A JAM ...........3-38

VII. POWER SUPPLY ......................3-43

CHAPTER 3 SADDLE STITCH UNIT

BASIC OPERATION

I. BASIC OPERATION ....................4-1

A. Outline ......................................4-1

B. Inputs to and Outputs from

Punch Driver PCB ....................4-2

II. PUNCH OPERATION ..................4-5

A. Outline......................................4-5

B. PUNCH OPERATION...............4-7

C. Horizontal Registration

Operation ...............................4-11

III. POWER SUPPLY SYSTEM.......4-14

CHAPTER 4 PUNCHER UNIT (OPTION)

BASIC OPERATION

CHAPTER 5 MECHANICAL CONSTRUCTION

I. FINISHER UNIT ..........................5-1

A. Externals and Controls.............5-1

B. FEEDING SYSTEM .................5-9

C. PCBs ......................................5-15

II. SADDLE STITCH UNIT .............5-16

A. Externals and Controls...........5-16

B. SADDLE UNIT .......................5-19

C. PCBs ......................................5-29

D. Accessory ..............................5-30

III. PUNCHER UNIT (OPTION) ......5-31

A. Externals and Controls...........5-31

B. Puncher Driver System ..........5-32

C. PCBs ......................................5-43

I. PERIODICALLY REPLACED

PARTS .........................................6-1

A. Finisher Unit .............................6-1

B. Saddle Stitch Unit ....................6-1

C. Puncher Unit (option) ...............6-1

II. CONSUMABLES AND

DURABLES .................................6-2

A. Finisher Unit .............................6-2

III. Consumable parts replacement

procedures ..................................6-3

A. Paddle replacement .................6-3

B. Knurled belt replacement .........6-4

IV. PERIODICAL SERVICING ........6-10

CHAPTER 7 TROUBLESHOOTING

I. ADJUSTMENTS ..........................7-1

A. Electrical System

(finisher unit) ............................7-1

B. Electrical System

(saddle stitch unit) ....................7-5

C. Electrical System

(puncher unit (option)) ..............7-7

II. ARRANGEMENT OF

ELECTRICAL PARTS ..................7-9

A. Finisher Unit .............................7-9

B. Saddle Stitch Unit ..................7-16

C. Puncher Unit (option) .............7-22

D. Light-Emitting Diodes (LED)

and Check Pins by PCB .........7-26

III. TROUBLESHOOTING...............7-28

A. Finisher Unit ...........................7-28

B. Saddle Stitch Unit ..................7-38

C. Puncher Unit (option) .............7-45

CHAPTER 6 MAINTENANCE AND INSPECTION

APPENDIX

A. FINISHER UNIT GENERAL

TIMING CHART.......................... A-1

B. SADDLE STITCH UNIT

GENERAL TIMING CHART ........ A-2

C. PUNCHER UNIT (option)

GENERAL TIMING CHART ........ A-3

D. SIGNAL AND

ABBREVIATIONS ....................... A-4

E. ACTUAL WIRING CHART .......... A-6

F. SOLVENTS AND OILS ............. A-13

CHAPTER 1

GENERAL DESCRIPTION

I. FEATURES ..................................1-1

II. SPECIFICATIONS .......................1-2

A. Finisher specifications

(AR-F15/F16) .............................1-2

B.Punch unit specifications

(AR-PN4) ...................................1-8

C. Engine specification

(AR-F15/F16/PN4) .................... 1-9

D. Cross Section ..........................1-11

III. Using the Machine.....................1-14

A. Removing Paper Jams from the

Finisher Unit.............................1-14

B. Supplying the Finisher Unit with

Staples .....................................1-15

C. Removing Staple Jams from the

Finisher Unit.............................1-17

D. Removing Paper Jams from the

Saddle Stitch Unit

(Saddle Finisher) .....................1-18

E. Supplying the Saddle Stitch

Unit with Staples

(Saddle Finisher) .....................1-20

F. Removing Staple Jams from the

Saddle Stitch Unit

(Saddle Finisher) .....................1-21

G. Removing Paper Jams from the

Puncher Unit (option) ...............1-23

H. Removing Punched Scrap from

the Puncher Unit (option) .........1-25

IV. MAINTENANCE BY THE

USER ........................................1-26

A. Maintenance by the User .........1-26

CHAPTER 1 GENERAL DESCRIPTION

1-1

I. FEATURES

1. Accommodates large quantities of sheets

• Normally, the finisher holds a stack of sheets 250 mm in height in its two bins (small-size

paper: equivalent to 2000 sheets)/140 mm in height (large-size paper: equivalent to 1000

sheets)

2. Has high paper transportation performance

• The finisher is capable of handling papers between 60 and 256 gm/m².

3. Offers a job offset function

• The finisher has a job offset function for sorting non-stapled stacks of copies.

4. Offers four types of auto stapling

• The finisher offers a choice of four stapling modes (1-point stapling at rear, diagonal sta-

pling at front, diagonal stapling at rear, 2-point stapling).

5. Uses a buffer roller

• The use of a buffer roller enables the finisher to accept copies without interruption from

the host machine even during stapling or offset operation.

6. Has a saddle stitch function (Saddle Finisher AR-F16)

• The finisher can staple along the center of paper and fold it in two (up to 15 sheets).

7. Offers a punch function (option)

• The use of the puncher unit enables the finisher to punch sheets for binders before they are

output. (The puncher unit is capable of handling papers between 60 and 256 gm/m². It can-

not handle special paper, postcards and transparencies.)

8. Insert function (option)

• Enable the use of special type of paper and printed paper in addition to the staple sorting or

the hole punching mode (Available when the optional staple sorting and the hole punching

mode units are installed.) This paper is not run through fuser (heat).

ITEM MODEL NOTE

Finisher AR-F15

AR-F16 Saddle stitch finisher

Punch unit AR-PN4A 2 holes (φ6.5) Europe

AR-PN4B 2 holes/3 holes automatic selection(φ8.0) North America

AR-PN4C 4 holes (φ6.5) (80mm pitch) France

AR-PN4D 4 holes (φ6.5) (70, 21mm pitch) Sweden

7 Stapler for Finisher

5000 staples

Staple cartridge x3 5000 x 3 SF-SC11 20 Cartridge for AR-F15/16

Common with S55,S55N,FN8/9

8 Stapler for Saddle

Stitch 2000 staples

Staple cartridge x3 2000 x 3 AR-SC3 40 For AR-F16 (Saddle Stitch Finisher)

Common with FN9

F15/F16

PN4

F15/F16

CHAPTER 1 GENERAL DESCRIPTION

1-2

II. SPECIFICATIONS

A. Finisher specifications (AR-F15/F16)

1. Finisher (AR-F15)

(1) Stack section

Type Floor installation

Stacking method Upper/Lower tray: Ascent/descent type offset tray

Transport speed 55 to 70 sheet/minute

Tray type Upper/Lower Tray Ascent/descent type offset tray

Output paper size AB series A4, B5, A5R, 16K, A3, B4, A4R, B5R, 8K, 16KR

Inch series 8.5 x 11, 5.5 x 8.5R, 11 x 17, 8.5 x 14, 8.5 x 13,

8.5 x 11R, 7.25 x 10.5R

Paper weight Plain paper: 60 to 105 g/m2

Thick paper: 106 to 256 g/m2

Paper transport

reference

Center reference

Mode type Non-staple, staple

Offset paper size A3, A4, A4R, B4, B5, 8K, 16K, 11 x 17, 8.5 x 14, 8.5 x 13, 8.5 x 11, 8.5 x 11R

Offset volume 30mm

Stacking performance Non-offset In horizontal direction: max. 30mm

In vertical direction: max. 50mm

(In the non-staple mode on the offset tray)

Offset In horizontal direction:

15mm or less for a same set,

15mm or more between different sets

Matching Max. deviation width 2.5mm

Output paper capacity <Tray1 / Tray2>

Non-staple:

2000 sheets (250mm ± 7mm)

A4, B5, A5R, 16K, 8.5 x 11, 5.5 x 8.5R: 80g/m2

1000 sheets (140mm ± 7mm)

A3, B4, A4R, B5R, 8K, 16KR, 11 x 17, 8.5 x 14, 8.5 x 13,

8.5 x 11R, 7.25 x 10.5R: 80g/m2

Stacking limit:

Tray1: Stack capacity from Tray1 & Tray2 = less than 2000 sheets

Tray2: Stack capacity from Tray2 = less than 2000 sheets

Staple:

110mm ± 7mm or 750 sheets or 100 sets

A4, B5, 8.5 x 11, 16K (S size)

74mm ± 7mm or 500 sheets or 100 sets

A3, B4, A4R, 11 x 17, 8.5 x 14, 8.5 x 13, 8.5 x 11R, 8K (L size)

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Sharp Imprimante tout-en-un

Sharp

Sharp MX-M950 Guide de démarrage rapide

Sharp

Sharp MX-M200D Manuel utilisateur

Sharp

Sharp MX-B427W Manuel utilisateur

Sharp

Sharp MX-7081 Mode d’emploi

Sharp

Sharp AL-2030 Manuel utilisateur

Sharp

Sharp AR-122E N Manuel utilisateur

Sharp

Sharp MX-M3050 Mode d’emploi

Sharp

Sharp MX-B557F Manuel utilisateur

Sharp

Sharp Advanced MXM365N Manuel utilisateur

Sharp

Sharp MX-M503U Manuel utilisateur

Sharp

Sharp IMAGER AR-5316 Manuel utilisateur

Sharp

Sharp MX-C312 Manuel utilisateur

Sharp

Sharp AR-C260M Manuel utilisateur

Sharp

Sharp MX-6240N Manuel utilisateur

Sharp

Sharp MX-7001N Series Manuel d'installation et d'exploitation

Sharp

Sharp AR-M208 Manuel utilisateur

Sharp

Sharp MX-C380 Manuel utilisateur

Sharp

Sharp MX 3070 Mode d'emploi

Sharp

Sharp MX-3610N Manuel utilisateur

Sharp

Sharp AR-M256 Manuel utilisateur

Sharp

Sharp AR-208S Guide de configuration

Sharp

Sharp AR-M300N. Manuel utilisateur

Sharp

Sharp MX-M503N Manuel utilisateur

Sharp

Sharp AL-2050CS Digital Multifunctional System... Manuel utilisateur

Manuels Imprimante tout-en-un populaires d'autres marques

Triumph Adler

Triumph Adler DC 2016 Manuel

Epson

Epson WorkForce WF-2510 Guide de l'utilisateur

Epson

Epson Stylus Scan 2000 Manuel d'installation et d'exploitation

Epson

Epson PictureMate Snap PM 240 Mode d’emploi

Konica Minolta

Konica Minolta bizhub C35 Manuel utilisateur

Brother

Brother MFC-J430w Manuel utilisateur

Konica Minolta

Konica Minolta BIZHUB 558 Manuel utilisateur

Lexmark

Lexmark MX710 Series Manuel

Brother

Brother MFC-9760 Manuel utilisateur

Lexmark

Lexmark XC8155 Manuel utilisateur

Lexmark

Lexmark X642E Manuel utilisateur

Aficio

Aficio 200 Manuel utilisateur

Canon

Canon ImageCLASS 2300 Manuel

Ricoh

Ricoh Pro C900 Manuel utilisateur

Lexmark

Lexmark X925 Manuel utilisateur

Brother

Brother Business Smart MFC-J4510dw Manuel utilisateur

Epson

Epson Stylus CX8400 Series Manuel utilisateur

Oce

Oce VarioLink 5022 Manuel utilisateur