SGM X-5 Manuel utilisateur

X·5 / XC·5

LED STROBE

X·5 / XC·5 LED Strobe dimensions

All dimensions in mm. Drawing not to scale.

X·5 / XC·5 LED STROBE

USER MANUAL REV. 3d ETL

panies disclaim liability for any injury, damage, direct or indirect loss, consequential or

economic loss or any other loss occasioned by the use of, inability to use or reliance on

the information contained in this manual. The SGM logo, the SGM name and all other

trademarNs in this document pertaining to serYices or products by SGM or its af¿liates and

subsidiaries are trademarNs oZned or licensed by SGM or its af¿liates or subsidiaries.

X·5 / XC·5 LED Strobe

Contents

Safety Information....................................................................................................5

Preparation for Use...................................................................................................7

Controller Operation.................................................................................................9

Setup..............................................................................................................10

DMX Control Summary...........................................................................................12

Service......................................................................................................14

DMX Protocols........................................................................................................15

Specifications.........................................................................................20

Users notes.......................................................................................................................22

Safety Information

Strobe lights are known to trigger epileptic seizures in persons who are photosensitive.

This product must be installed in accordance with the applicable installation code by a person familiar with the

construction and operation of the product and the hazards involved.

Ce produduit doit être installé selon le code d’installation pertinent, par une personne qui connaît bien le produit

et son fonctionnement ainsi que les risques inhérents.

• Do not open: there are no user-serviceable parts inside.

• $lways ground earth the ¿[ture electrically.

• Use only a source of AC power that compiles with local building and electrical codes and has both overload and

earth leakage protection.

• Do not e[pose the ¿[ture to rain or moisture.

WARNING!

This product is for professional use only! It is not for household use.

To guard against electric shock.

• Do not stare directly into the light.

• 1ever attempt to bypass the fuse. Always replace defective fuses with ones of the speci¿ed type and rating.

• 9erify that the power feed cable is rated for the current draw of all connected ¿[tures.

• .eep all combustible materials for e[ample fabric, wood, paperat least 0.5 meters 20 inchesaway from the

¿[ture. .eep Àammable materials well away from the ¿[ture.

• Provide a minimum clearance of 0.1 meters (4 inches) around air vents.

• Do not modify the ¿[ture or install other than genuine SGM parts.

• Do not operate the ¿[ture if the ambient air temperature (Ta) e[ceeds 40ÛC (104Û)).

• Caution: ([terior surface temperature after 5 min. operation 40ÛC (104Û)) Steady state 75ÛC (195Û)).

• Do not operate the ¿[ture near stairways.

• Provide advance notice that strobe lighting is in use.

• Avoid e[tended periods of continuous Àashing, particularly at frequencies of 10 to 20 Àashes per second.

To guard against 89 radiationEurnand ¿re.

To guard against epileptic seizure..

Preparation for Use

Unpacking

• Strobe /ight )i[ture

• User manual

• Mains power cable

• )oot íblack aluminium plate

The packing material protects the ¿[ture during shipment, please retain for future transportation of the ¿[ture.

AC Power Connection

The auto-ranging power supply automatically adjusts to AC power from 208-240 volts nominal at 50/60 Hz.

The current required by the X-5/XC-5 is 4 amps. To avoid overload, allow one 4 amp branch circuit per ¿[ture to

operate the X-5/XC-5 model at full power.

Use 2.5 mm2 (13 AWG) or larger power feed cables and keep runs as short as possible.

)or temporary installation, the mains cable may be ¿tted with a grounded connector.

The power cable color coding is given in the table.

• Connect the brown wire to live

• Connect the blue wire to neutral

• Connect the green/yellow wire to ground (earth)

The device must be grounded/earthed and be able to be isolated from AC power. The AC power supply must incorporate a fuse or

circuit breaker for fault protection.

7o rig tKe ¿[tXre

Before installing;

• Verify that the attachment hardware is in good condition and designed to carry at least 10 times the ¿[ture’s weight.

• Verify that the structure can support at least 10 times the weight of all installed ¿[tures, clamps, cables, au[iliary equipment, etc.

• Verify that the clearance around the air vents is at least 0.1 meters (4 in.).

• /oosen the mounting bracket and adjust the ¿[ture to the desired angle.

• Connect and arrange the power and data cables.

• Min. safety wire gauge 3mm.

Always use a secure means of secondary ¿[ing such as a safety wire

Controller Operation

This section describes how to operate the X-5/XC-5 with a DMX controller.

Data Connection

The X-5/XC-5 provided 5-pin XLR connectors for data connection. The pin-out on all connectors is pin 1 to shield,

pin 2 to cold (-), and pin 3 to hot (+). There is no connection to pins 4 and 5.

To connect the data link

1. Connect the DMX data output from the controller to the ¿[ture 5-pin input (male) socket.

2. Connect up to 31 additional ¿[tures output-to-input.

3. Insert a termination plug in the output of the last ¿[ture on the link.

Data Connection Tips

• Use shielded twisted-pair cable designed for DMX devices: standard microphone cable cannot transmit control

data reliably over long distance. 24 AWG cable is suitable for distances up to 300 meters (1000 ft.). Use heavier

gauge cable and/or a DMX splitter/amp for longer distances.

• Do not overload the link. Up to 32 devices may be connected on a serial link.

• Terminate the link by installing a termination plug in the output socket of the last ¿[ture. The termination plug,

which is a male XLR plug with a 120 ohm, 0.25 watt resistor soldered between pins 2 and 3, absorb the control

signal so it does not reÀect and cause interference.

Setup

The ¿[ture uses an interactive display for setting up DMX address and operation mode. Use the ¿ve buttons ne[t to the

display to navigate the setup structure (Fig. 1).

When the product is switched on, the ¿[ture will be at its default setting showing the ROOT menu (Fig. 2).

The root menu show a summary of the setup information, including selected DMX address, operation mode, data indicator

and protocol.

Fig. 1 Fig. 2

Operation

mode

DMX

Address

Data

protocol

Data

indicator

Autres manuels pour X-5

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels SGM Projecteur

SGM

SGM G-SPOT Manuel utilisateur

SGM

SGM G-PROFILE Manuel utilisateur

SGM

SGM G-7 SPOT Manuel utilisateur

SGM

SGM G-SPOT Manuel utilisateur

SGM

SGM Q?7 Manuel utilisateur

SGM

SGM Q?2 White Manuel utilisateur

SGM

SGM P-5 Wash Light Manuel utilisateur

SGM

SGM P-2 WASH LIGHT Manuel utilisateur

SGM

SGM P-5 Wash Light Manuel utilisateur

Manuels Projecteur populaires d'autres marques

VIZULO

VIZULO Micro Martin Guide de l'utilisateur

EuroLite

EuroLite LED IP FL-100 SMD Manuel utilisateur

Cooper Wheelock

Cooper Wheelock XB12 Manuel utilisateur

Allen + Roth

Allen + Roth 17624-000 Manuel utilisateur

ADJ

ADJ 4 STAGE PAK Manuel utilisateur

Cooper Lighting

Cooper Lighting EGL91SW233 Manuel utilisateur

Max

Max 37496 Manuel utilisateur

BEGA

BEGA 85 143 Manuel utilisateur

Beamz

Beamz 151.226 Manuel utilisateur

EuroLite

EuroLite LED IP FL-8 Manuel utilisateur

Ledj

Ledj PERFORMER 36 RGB Manuel utilisateur

Perel

Perel ELS3 Manuel utilisateur

Perel

Perel ELS3WD Manuel utilisateur

LumX

LumX LM 36130 Manuel utilisateur

Xtricity

Xtricity 4-80053 Manuel utilisateur

Stahl

Stahl 6521/4 Series Manuel utilisateur

Ecosense

Ecosense EcoSpec Manuel utilisateur

Ayrton

Ayrton minipanel FX Manuel utilisateur