SG Wireless SGW6008 Manuel utilisateur
SGW6008 BLE WiFi Gateway
User Manual
Version 1.1
SGW6008 BLE Gateway User Manual
Page 2 of 13
1. Introduction
The SGW6008 is a Bluetooth Low Energy ®(BLE) to Wi-Fi connectivity gateway without using
smartphones or apps. This robust gateway collects data from BLE sensors or devices, and sends
to the local server or remote cloud server by HTTPS & MQTTS protocols with TLS1.2 standard
over Wi-Fi. A connected solution for the SGW8130 BLE sensor tag and SGW111X BLE module,
the SGW6008 enables hassle-free real time remote monitoring or asset tracking for IoT
applications
2. Features
oSGW1010 BLE module
oOperating system: Amazon FreeRTOS
o2.4GHz 802.11 b/g/n WiFi
oProtocol: TCP/HTTPS/MQTTS/TLS1.2
oLED status indicators –Power, WiFi & BLE
oButton: AP mode for Wi-Fi configuration and Gateway provisioning
oPower Input: 1A @5V DC, micro-USB interface
oDimension: 66.75mm x 65.75mm x 23.5mm
oOperating temperature: -10°C to 60°C
3. Applications
oIndustrial mesh networks
oIndustrial smart lighting
oSmart logistics and transportation
oSmart devices for connected homes
oSmart city infrastructure
SGW6008 BLE Gateway User Manual
Page 3 of 13
4. Block Diagram
Below (Fig.1) is the block diagram of the SGW6008 BLE WiFi Gateway.
Figure 1. SGW6008 BLE WiFi Gateway Block Diagram
5. SGW6008 BLE WiFi Gateway
User interface and connector available on the SGW6008 BLE WiFi Gateway are shown below
(Figure 2)
Figure 2. SGW6008 BLE WiFi Gateway
Connector/Button
Description
USB
Micro-USB, power input (5.0V DC, 1A)
Button
AP mode for Wi-Fi configuration and Gateway provisioning
SGW6008 BLE Gateway User Manual
Page 4 of 13
Top LEDs present on the SGW6008 BLE WiFi Gateway indicates the following status:
Power LED
Bluetooth LED
WFi LED
Normal Operation
Power-on
On
-
-
Bluetooth Signal transmission
On
Blinking
-
WiFi Signal transmission
On
-
Blinking
AP Mode Operation
AP mode, Not connected
Blinking
-
Blinking
AP mode, connected
Blinking
-
On
WiFi configuration success and
connected to SG Wireless IoT server
On
-
Blinking
Figure 3. Internal Structure of SGW6008
SGW6008 BLE Gateway User Manual
Page 5 of 13
6. Electrical Specifications
Absolute Maximum Rating
Power supply
5.5V DC
Storage temperature
-20°C to 80°C
Recommended Operating Conditions
Power supply
5.0V DC
Operating temperature
-10°C to 60°C
BLE RF Performance
Radio Operating Frequencies
2402MHz ~ 2480MHz
Radio On-Air Data Rate
1Mbps, 2Mbps
Maximum Transmit Power
10+/-2dBm
Antenna
Onboard PCB Antenna
Range
Up to 200 meters (open space)
WiFi Performance
Wireless Standard
IEEE 802.11b/g/n (single stream)
Radio Operating Frequencies
US band: Channel 1-11
EU band: Channel 1-13
Radio On-Air Data Rate
IEEE 802.11b, 1-11Mbps
IEEE 802.11g, 6-54Mbps
IEEE 802.11n(2.4GHz), 72.2Mbps
Maximum Transmit Power
17+/-2dBm
Antenna
Onboard PCB Antenna
Security
WPA/WPA2
Encryption
WEP/TKIP/AES
SGW6008 BLE Gateway User Manual
Page 6 of 13
7. Getting Started
7.1 Wi-Fi Configuration and Provisioning of SGW6008
Wi-Fi configuration and gateway provisioning process must be finished first in order to use
the functionalities of the SGW6008.
1. Power-up the SGW6008 BLE WiFi Gateway with micro-USB cable.
2. Connect the gateway with your computer or mobile device.
a. SSID of the SGW6008 BLE WiFi Gateway: “SGW6008_AA:BB:CC:DD:EE:FF”
b. Default password of the SGW6008 BLE WiFi Gateway: “SGWireless_23$”
3. Launch your Internet browser, and go to the following web address: http://192.168.4.1
SGW6008 BLE Gateway User Manual
Page 7 of 13
Wi-Fi configuration procedures:
4. Press “Scan” button in main page to scan for available Wi-Fi Access points in the area.
5. Enter the password for target Wi-Fi access point and press “+” in Action.
6. Press “OK” to confirm the setting in the Popup windows as shown below:
SGW6008 BLE Gateway User Manual
Page 8 of 13
7. If static IP is preferred, select “No” for DHCP and enter the IP address, Subnet Mask and
DNS of the WiFi access point in the WI-FI configuration table. Press “Save Wifi Setting”
button to update the setting.
* The “High Priority Slot” represents which saved SSID is the highest priority to connect with.
Gateway provisioning procedures:
8. Fill in the SGW IoT Platform account and gateway information, then select “Start
Provisioning”.
9. Press “OK” to the prompt shown as below.
SGW6008 BLE Gateway User Manual
Page 9 of 13
10. Upon confirmation, the gateway will exit AP mode and start the provisioning with SGW
IoT Backend server. During the process, the configuration web page will be directed to SG
IoT Website. Please make sure your PC or mobile device has switched to networks with
proper internet connection.
7.2 Edge Devices Provisioning
The SGW8130 BLE Sensor Tag can be connected to the SGW6008 BLE WiFi Gateway.
Provisioning procedures for edge devices SGW8130:
1. Log-in to SG Wireless IoT Dashboard
a. Visit SG IoT Dashboard Page: “https://www.sg-iot.com”and log-in
b. Click ‘Gateway’ and it will show all provisioned gateways. Select the target gateway to configure.
SGW6008 BLE Gateway User Manual
Page 10 of 13
2. Search and Connect Edge Device
a. Click ‘SEACH NEW BLE’ to search for nearby edge devices SGW8130.
b. Click the Green Discovered BLE device icon which is showing the Mac Address of your target edge device
c. Fill in the information of the edge device (name, location, description)
d. Click “SUBMIT” to provision the edge device
e. The registered edge device will be shown in the BLE Device’s list
Autres manuels pour SGW6008
1
Table des matières
Autres manuels SG Wireless Porte
Manuels Porte populaires d'autres marques
LST
LST M500RFE-AS Manuel utilisateur
Kinnex
Kinnex Media Gateway Manuel utilisateur
2N Telekomunikace
2N Telekomunikace 2N StarGate Manuel utilisateur
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur
Telsey
Telsey CPVA 500 - SIP Manuel utilisateur
