SG Wireless SGW101 Series Manuel utilisateur

SGW101X BLE Modules Series

Model：SGW1010，SGW1010A，SGW1011，SGW1011A

SGW101X Series

@2019 | SG Wireless Limited

Confidential Proprietary

Website : www.sgwireless.com

1. Introduction

The SGW101X series is an advanced, highly flexible, ultra-low power multiprotocol SoM that enable Bluetooth (BLE)

connectivity for portable, extremely low power embedded systems.

The SGW101X series delivers robust RF performance, low energy consumption, a wide selection of MCU peripherals and

either an integrated PCB trace antenna or a u.FL connector for an external antenna. These modules are created to

minimize the engineering efforts and development costs associated with adding Bluetooth 5.0 to any product,

accelerating its time-to-market.

2. Features

oComplete RF solution with integrated antenna or external antenna.

oBluetooth 5 ready multi-protocol module:

o2Mbps

oLong Range

oAdvertising Extension support

oWireless System-on-Chip: Nordic nRF52840:

o32-bit ARM Cortex™-M4F CPU @64MHz

o1MB Flash program memory

o256kB RAM data memory

oWide selection of MCU Peripherals:

oFull-speed USB (12Mbps)

oFour SPI Master/Slave (8Mbps)

oTwo 2-wire Master/Slave (I2C compatible)

oTwo UARTs (with CTS/RTS)

oNFC Tag-A interface

o20 channel CPU independent Programmable Peripheral Interconnect (PPI)

o5x32 bit, 3x24bit Real Timer Counters (RTC)

o12-bit/200K SPS ADC

oSupport 128-bit AES HW encryption

o48 General Purpose I/O pins

oSupply voltage: 1.7–5.5V

oLow Energy Current consumption, 3V DCDC enabled:

oTx only, 0dBm: 4.8mA (typical)

oRx only @1Mbps: 4.6mA (typical)

SGW101X Series

@2019 | SG Wireless Limited

Confidential Proprietary

Website : www.sgwireless.com

oSystem On mode, with full RAM retention: 2.35uA

oSystem Off mode, with full RAM retention: 1.86uA

oOperating Temperature: −40°C to 85°C

oCE Pending

oBQB: Pending

oFCC: 2AS9401

oIC: 25021-01

oMechanical Dimension: 10.2mm x 15.0mm x 2.1mm

APPLICATIONS

oConnected home

oSmart city infrastructure

oIndustrial mesh networks

oIndustrial smart lighting

oLogistics and transportation

SGW101X Series

@2019 | SG Wireless Limited

Confidential Proprietary

Website : www.sgwireless.com

1. Introduction................................................................................................................................................1

2. Features......................................................................................................................................................1

3. Ordering Information..................................................................................................................................4

4. Electrical Specifications.............................................................................................................................. 5

A. Absolute Maximum Ratings...............................................................................................................5

B. Operating Conditions......................................................................................................................... 5

5. Module Interface........................................................................................................................................6

A. Power Management.......................................................................................................................... 6

B. RF antenna interface..........................................................................................................................7

C. General Purpose I/O.......................................................................................................................... 7

6. Mechanical Dimension............................................................................................................................... 9

7. Module Marking....................................................................................................................................... 10

8. Soldering Temperature-Time Profile for Re-Flow Soldering......................................................................11

9. Certifications............................................................................................................................................ 12

A. Qualified Antenna Type................................................................................................................... 12

B. Bluetooth......................................................................................................................................... 12

C. FCC Statement..................................................................................................................................13

D. IC Statement.................................................................................................................................... 14

10. Product Packaging.................................................................................................................................. 16

11. Revision History...................................................................................................................................... 17

12. Useful Link.............................................................................................................................................. 17

SGW101X Series

@2019 | SG Wireless Limited

Confidential Proprietary

Website : www.sgwireless.com

3. Ordering Information

Part No

Description

SGW1010

Bluetooth 5 module, Built-in antenna

SGW1011

Bluetooth 5 module, u.FL connector for external antenna

SGW1010A

Bluetooth 5 module, Built-in antenna, Low voltage operation

SGW1011A

Bluetooth 5 module, u.FL connector for external antenna, Low voltage operation

SGW1010–EVK

SGW1010 Bluetooth 5 module Evaluation Kit

SGW101X Series

@2019 | SG Wireless Limited

Confidential Proprietary

Website : www.sgwireless.com

4. Electrical Specifications

A. Absolute Maximum Ratings

Symbol

Parameter

Min.

Max.

Unit

VCCmax

Voltage on VCC supply pin

-0.3

3.9

VCCHmax

Voltage on VCCH supply pin

-0.3

5.8

VBUSmax

Voltage on VBUS supply pin

-0.3

5.8

VIOmax

Voltage on GPIO pin (VCC > 3.6V)

-0.3

3.9

VIOmax

Voltage on GPIO pin (VCC ≤ 3.6V)

-0.3

VCC+0.3V

Tstorage

Storage Temperature Range

-40

125

℃

Table 3 Absolute Maximum Ratings

B. Operating Conditions

Symbol

Parameter

Min.

Typ.

Max.

Unit

VCC

VCC Operating supply voltage

1.7

3.0

3.6

VCC

VCC DCDC Startup voltage

1.75

3.0

3.6

VCCH

VCCH Operating supply voltage

2.5

3.7

5.5

VBUS

VBUS USB supply voltage

4.35

5.0

5.5

TR_VCC

VCC Supply Rise time (0V to 1.7V)

TR_VCCH

VCCH Supply Rise time (0V to 3.7V)(1)

100

TAmbient

Operating Temperature Range

-40

℃

REMARK:

(1): Applicable to module configures as nRF52840 HV mode.

SGW101X Series

@2019 | SG Wireless Limited

Confidential Proprietary

Website : www.sgwireless.com

5. Module Interface

A. Power Management

i. Module supply input (VCC & VCCH)

The SGW101X series use integrated two step-down regulators (REG0 & REG1) to transform the supply voltage presented

at the VCC & VCCH pins into a stable system voltage. Each regulator can be programmed as Low-dropout regulator

(LDO) or Buck regulator (DC/DC), depends on the operating mode of the module. There are two operating modes for

the module which depends on the VCC and VCCH configuration:

oNormal/Low Voltage (LV) mode

oHigh Voltage (HV) mode

Mode

Pin No

Pin Name

Connection

Normal

VCC

1.7 V to 3.6 V supply source input

VCCH

Same as VCC

High Voltage

VCC

1.8 V to 3.3 V output voltage for module internal operating supply

VCCH

2.5 V to 5.5 V supply source input

REMARK: In LV or HV mode, the GPIO logic level is determined by the VCC pin.

Table 5 Power Mode Pin connections

ii. USB Power input (VBUS)

The USB interface of the SGW101X series can be used in either Normal (LV) or High voltage mode of the module. The

inside USB peripheral has a dedicated internal voltage regulator for converting the VBUS supply to 3.3 V.

SGW101X Series

@2019 | SG Wireless Limited

Confidential Proprietary

Website : www.sgwireless.com

B. RF antenna interface

i. 2.4 GHz radio

The SGW101X series BLE module have their own 2.4 GHz antenna solutions respectively:

oThe SGW1010/SGW1010A modules use a PCB trace antenna integrated into the module’s PCB. This low-profile

antenna solution is useful in space constrained designs.

oThe SGW1011/SGW1011A modules provide an onboard antenna connector with a nominal characteristic

impedance of 50 Ω.

ii. Near Field Communication (NFC)

The SGW101X series modules include a Near Field Communication interface capable of operating as a 13.56 MHz NFC

tag, at a bit rate of 106 kbps. As an NFC tag, the data can be read from or written to the SGW101X modules using an

NFC reader.

Two pins are available for connecting to an external NFC antenna: NFC1 (P0.09) and NFC2(P0.10).

C. General Purpose I/O

There are total 48 available GPIO pins for user application. Each pin can be programmable individually with following

configurable features:

oInput/output direction

oOutput drive strength

oInternal pull-up and pull-down resistors

oWake-up from high or low-level triggers on all pins

oTrigger interrupt on all pins

oAll pins can be individually configured as serial interface or quadrature demodulator signals

Symbol

Parameter

Min.

Typ.

Max.

Unit

VIH

Input High Voltage

0.7 x VCC

VCC

VIL

Input Low Voltage

VSS

0.3 x VCC

VOH

Output High Voltage

VCC – 0.4

VCC

VOL

Output High Voltage

VSS

VSS + 0.4

RPU

Pull-up Resistance

kΩ

SGW101X Series

@2019 | SG Wireless Limited

Confidential Proprietary

Website : www.sgwireless.com

RPD

Pull-down Resistance

kΩ

i. Serial interfaces

The SGW101X series provide the following serial communication interfaces:

o2x UART interfaces: 4-wire universal asynchronous receiver/transmitter interface used for AT command interface,

data communication, and u- connect software upgrades using the Software update +UFWUPD AT command.

o3x SPI interfaces: Up to three serial peripheral interfaces can be used simultaneously.

o1x QSPI interface: High speed interface used to connect to the external flash memories.

o2x I2C interfaces: Inter-Integrated Circuit (I2C) interface for communication with digital sensors.

o1x I2S interface: Used to communicate with external audio devices.

o1x USB 2.0 interface: The USB device interface to connect to the upstream host.

ii. Analog interfaces

8 out of the 48 digital GPIOs can be multiplexed to analog functions. The following analog functions are available:

o1x 8-channel ADC

o1x Analog comparator (*)

o1x Low-power analog comparator (*)

REMARK

(*): Only one comparator can be used at any given point of time.

iii. Module Reset

The modules can be reset using one of the following ways:

oLow level on the nRESET (P0.18) input pin, normally kept high using an internal pull-up. This causes an “external” or

“hardware” reset of the module.

oUsing the AT+CPWROFF command. This causes an “internal” or “software” reset of the module.

iv. Debug and Programming interfaces

The SGW101X series modules provide an SWD interface for flashing and debugging. The SWD interface consists of two

pins –SWDCLK and SWDIO.

The SGW101X series modules also support parallel trace output. This allows output from the Embedded Trace Macrocell

(ETM) and Instrumentation Trace Macrocell (ITM) embedded in the Arm Cortex-M4 core of the nRF52840 chip. The ETM

SGW101X Series

@2019 | SG Wireless Limited

Confidential Proprietary

Website : www.sgwireless.com

trace data allows a user to record exactly how the application goes through the CPU instructions in real time. The

parallel trace interface uses 1 clock signal and 4 data signals respectively – TRACE_CLK, TRACE_D0, TRACE_D1,

TRACE_D2 and TRACE_D3.

6. Mechanical Dimension

Figure 7 SGW1010/SGW1010A (Embedded Antenna) Mechanical Information

Figure 8 SGW1011/SGW1011A (External Antenna) Mechanical Information

Ce manuel convient aux modèles suivants

Table des matières

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur