SEWOO LK-D10 Manuel utilisateur

All specifications are subject to change without notice

Mini Dot Impact Printer

MODEL : LK-D10

1. Features 3

2. Specication 4

3. Self Test 6

4. Conguration Setup 7

5. User Switches 8

5.1. Panel Switches 8

5.2. Power Switch 8

5.3. Indicators 8

6. Command List 9

6.1. EMULATION EPSON TM-U200 9

6.2. EMULATION CITIZEN iDP-3540 10

6.3. EMULATION VERIFONE 900 11

6.4. EMULATION STAR SP200 12

7. Interface 13

7.1. Serial interface 14

7.1. Parallel interface 15

8. Cash Drawer Connector 16

9. Power Supply 17

10. Dip Switch Settings 18

10.1. External Dip Switch 18

10.2. Internal Dip Switch 19

Table of Contents

♣Power Supply Requirements

Either input 120VAC/Output 24VDC 2.5A for North America or Input 230VAC/Output 24VDC 2.5A for

Europe with a 3pin mini-din connector power supply is provided.

♣Dip Switch Configuration

Emulation mode, CPL Select mode, Flow Control mode, Data Width/Parity, and Baud Rate are all

configured through dip switch settings.

♣Data Buffer

The printer has a built-in 48 Kilobyte I/O buffer allowing the host computer to free itself after sending

the print data.

♣Reliable communications

Centronics parallel or RS-232C compatible communications is built-in. The printer supports multiple

baud rates, emulations, and handshaking on its parallel & serial interfaces.

♣User controls

A power switch, a paper forward FEED button, a paper BACKward feed button and ON LINE button

provide ease of use.

♣Self Test Mode

A comprehensive self-test mode is available which describes the printer configuration and dip switch

setting information along with the version number of firmware installed.

♣Print orientation

The printer is capable of printing normal and upside down. The print orientation is selected by software

commands.

♣Selectable international characters

The printer supports international characters selectable by software control.

♣Multiple Fonts/Sizes

Two different resident fonts are available for printing diversity. Each of these fonts can be printed

in normal, double wide, double height, and quadruple sizes. Both fonts and sizes are selected by

software.

♣Error detection

The printer can detect paper-out and paper-jam as well as controller malfunction.

♣Peripheral Drive

Two cash drawer drivers are provided.

♣Certification

(1) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions:

1) this device may not cause harmful interference , and

2) this device must accept any interference received , including interference that may cause

undesired operation.

(2) UL/cUL (UL 60950-1)

(3) MIC

(4) CE-EMCD (CE-EMCD Class B should use Parallel shield Cable complied with IEEE-1284 standards)

(5) RoHS (TUV)

(6) CCC

1. Features

MODEL LK-D10

PRINT METHOD 9-pin serial impact dot matrix

PRINT DIRECTION Bi-directional (with logical seeking)

NO. OF COLUMNS Epson Mode : 42/35, 40/33, Star Sp-200 : 42/35

Other Modes : 40/32

NO. OF DOTS/LINE 320 dots 400 dots

FONT SIZE 5 x 9, 7 x 9 dots 7 x 9, 9 x 9 dots

LINE SPACING n/144 inch

PRINTING WIDTH 63.5mm (2.5”)

PRINT SPEED 3.2 lines/sec

INK RIBBON EPSON, ERC-23 compatible

Black or Purple

PAPER Media Roll Paper Sprocket Fanfold

Width 76.2mm (3.0”) 88.9mm (3.5”)

Diameter 76.2mm (3.0”) max

Copies 3-ply max. (0.2mm or 0.008” thick)

DATA BUFFER 48K bytes

CASH DRAWER DRIVER 2 circuits (24V, 1A max)

INTERFACE

RS-232C Serial (25Pin) Parallel (25Pin)

Centronics Parallel (36Pin) or

RS-232C Serial (9Pin)+MSR

EMULATION Epson TM-U200, TM-U300, Citizen iDP-3540

Star SP200

POWER SUPPLY Type External Adaptor

Input 120VAC(North America) or 230VAC(Europe),

110/220V Selectable

Output 24VDC 2.5A (North America)

or 24VDC 2.5A (Europe)

OPERATING CONDITION 5°C to 40°C, 10% to 80% RH

STORAGE CONDITION -20°C to 60°C, 5% to 95% RH

RELIABILITY MCBF 5 million lines

Printhead 100 million characters

DIMENSIONS Roll Type 161(W) x 282(D) x 126(H)mm

Sprocket Type 161(W) x 282(D) x 144(H)mm

WEIGHT 2.87 lbs (1.3 kg)

2. Specification

Printer Specifications

Overall dimension

3. Self Test

1) While pressing the paper FEED switch after the printer in turned on the self test mode is initiated. The

printer self test includes a listing of the current default settings and Dip Switch information.

2) While pressing the paper BACK switch after the printer in turned on the self test mode is initiated.

The printer self test includes a listing of internal memory test, print head pin firing test, vertical line

alignment test, and multiple character fonts/sizes.

3) While pressing the paper ON LINE switch after the printer in turned on the self test mode is initiated.

The printer self test includes a listing of multiple international fonts and code pages.

The printer then enters into the On Line mode.

When the paper FEED switch is pressed and released instantly as the power is applied to the printer, the

printer will print the current printer configuration settings along with the DIP switch information. If the

printer setup needs to be changed, turn the Power Off before changing the setting.

The printer will be setup at the factory as follows;

Dip SW information

========================== ===========================

Firmware : Ver X.XX Emulation SW1

Loopback : Not Detected(DSR) Epson TM-U200 OFF

========================= Citizen iDP3540 ON

Interface : Serial -----------------------------------------

Emulation : Epson TM-U200 CR Character SW2

CR Character : CR = CR only CR = CR Only OFF

Flow Control : DTR/DSR CR = CR + LF ON

Data Bits : 8 Bits ------------------------------------------

Parity : None CPL SW3

Baud Rate : 9600 40 Char/Line OFF

CPL : 40/33 CHAR/LINE 30 Char/Line ON

Two Color : Not Installed -------------------------------------------

Auto Cutter : Not Installed Flow Control SW4

Paper : Roll Type DTR/DSR OFF

Xon/Xoff ON

-------------------------------------------

Baud Rate SW5 SW6

9600 OFF OFF

4800 ON OFF

2400 OFF ON

1200 ON ON

-------------------------------------------

Data Bits/Parity SW7 SW8

8Bits None - OFF

7Bits Odd OFF ON

7Bits Even ON ON

=========================

SETUP PRINT END

****************************

PRINTER READY…………

4. Configuration Setup

5.1. Panel Switches

FEED button

Advance media in line feed increments if the FEED switch is pressed momentarily.

If the FEED switch is pressed for more than 1 seconds, the media will advance continuously until the

switch is released.

BACK button

Feed the media back in each line increment until 20 lines back if the BACK switch is pressed momentarily.

If the BACK switch is pressed for more than 1 second, the media will be fed back continuously up to 20

lines until the switch is released.

ON LINE button

If the switch is pressed, the printer turns to be in OFF LINE mode, and if pressed again, the printer is in

ON LINE mode and ready to print.

5.2. Power Switch

A Power switch located on the lower back side of the printer is used to turn the printer ON and OFF.

5.3. Indicators

This section explains the different patterns signaled by the two LED indicators located on the top cover

of the Printer.

STATUS LED1 LED2 REMARKS

RED GREEN

Power Off OFF OFF Normal power is not supplied to the printer

Power On Flash ON Normal power is supplied to the printer

On line OFF ON Normal error-free mode

Paper empty Flash ON Insert new paper roll

Paper jam ON OFF Remove the paper in the printer

Test mode ON ON Printer in self-test mode

5. User Switches

6.1. EMULATION EPSON TM-U200

Command Hex Code Description

HT <09>H Horizontal tab

LF <0A>H Print and line feed

CR <0D>H Carriage Return

DLE EOT <10>H<04>H<n> Real-time status transmission

DLE ENQ <10>H<05>H<n> Real-time request to printer

ESC SP <1B>H<20>H<n> Set right-side character spacing

ESC ! <1B>H<21>H<n> Set print mode

ESC % <1B>H<25>H<n>S Select/cancel user-defined character set

ESC & <1B>H<26>H Define user-defined characters

ESC * <1B>H<2A>H Select bit-image mode

ESC - <1B>H<2D><n> Turn on/off underline mode

ESC 2 <1B>H<32>H Select 1/6 inch line spacing

ESC 3 <1B>H<33>H<n> Set line spacing

ESC < <1B>H<3C>H Return home

ESC = <1B>H<3D>H<n> Select peripheral device

ESC ? <1B>H<3F>H<n> Cancel user-defined characters

ESC @ <1B>H<40>H Initialize printer

ESC D <1B>H<44>H<n> Set horizontal tab positions

ESC E <1B>H<45>H<n> Turn on/off emphasized mode

ESC G <1B>H<47>H<n> Turn on/off double-strike mode

ESC J <1B>H<4A>H<n> Print and feed paper

ESC R <1B>H<52>H<n> Select an international character set

ESC U <1B>H<55>H<n> Turns on/off unidirectional printing mode

ESC a <1B>H<61>H<n> Select justification

ESC c 4 <1B>H<63>H<34>H<n> Select paper sensor to stop printing

ESC c 5 <1B>H<63>H<35>H<n> Enable/disable panel button

ESC d <1B>H<64>H<n> Print and feed n lines

ESC p <1B>H<70>H Generate pulse

ESC t <1B>H<74>H<n> Select character code table

ESC { <1B>H<7B>H<n> Turn on/off upside-down printing mode

GS I <1D>H<49>H<n> Transmit printer ID

GS a <1D>H<61>H<n> Enable/disable Automatic Status Back

GS r <1D>H<72>H<n> Transmit status

6. Command List

Table des matières

Autres manuels SEWOO Imprimante

SEWOO

SEWOO SLK-TE25 Manuel utilisateur

SEWOO

SEWOO LK-P300 Manuel utilisateur

SEWOO

SEWOO LK-P SERIES Feuille d'instructions

SEWOO

SEWOO LK-P41W Manuel utilisateur

SEWOO

SEWOO SLK-TE32 Series Manuel utilisateur

SEWOO

SEWOO WTP-100 Manuel utilisateur

SEWOO

SEWOO SLK-TS400 Manuel utilisateur

SEWOO

SEWOO LK-P30 II Manuel utilisateur

SEWOO

SEWOO LK-T210 Manuel utilisateur

SEWOO

SEWOO LK-B10 Manuel utilisateur

SEWOO

SEWOO LK-P20II Manuel utilisateur

SEWOO

SEWOO SLK-TL12X Series Manuel utilisateur

SEWOO

SEWOO LK-P11 Instructions d'installation

SEWOO

SEWOO LUKHAN LK-P21B Manuel utilisateur

SEWOO

SEWOO LK-T41 Manuel utilisateur

SEWOO

SEWOO SLK-T32EB II Manuel utilisateur

SEWOO

SEWOO SLK-TE21X Series Manuel utilisateur

SEWOO

SEWOO LUKHAN LK-P21B Manuel utilisateur

SEWOO

SEWOO SLK-TL20 Series Manuel utilisateur

SEWOO

SEWOO WTP-150 Manuel utilisateur

SEWOO

SEWOO SLK-T32EB Series Manuel utilisateur

SEWOO

SEWOO SLK-TS400EB Manuel utilisateur

SEWOO

SEWOO SLK-TL100 Manuel utilisateur

SEWOO

SEWOO SLK-TE25 Manuel utilisateur

Manuels Imprimante populaires d'autres marques

Lexmark

Lexmark 1400 Series Manuel

Canon

Canon i70 Series Manuel utilisateur

Evolis

Evolis Elypso Manuel utilisateur

Kyocera

Kyocera FS-9530DN Manuel utilisateur

Canon

Canon LASER SHOT LBP-1210 Manuel utilisateur

Samsung

Samsung BIXOLON SRP-350plusF Manuel utilisateur

Canon

Canon PIXMA PRO-1 Series Manuel utilisateur

Canon

Canon PIXMA G3560 Guide de configuration

Dell

Dell Color Laser Printer 2130cn Manuel utilisateur

Tektronix

Tektronix Phaser 840 Manuel utilisateur

Epson

Epson ET-7750 Mode d'emploi

Canon

Canon CLBR 460ps Manuel utilisateur

Eltron

Eltron P210 Guide Manuel utilisateur

Ricoh

Ricoh MD-P1 Manuel utilisateur

Epson

Epson SC-F7100 series Manuel utilisateur

Epson

Epson Stylus C40UX Manuel utilisateur

Canon

Canon imagePASS-A2 Manuel utilisateur

Canon

Canon S820D Manuel utilisateur