Sercomm NA910A Manuel utilisateur

Home Monitoring

Gateway

NA910

User Guide

Table of Contents

CHAPTER 1 INTRODUCTION .............................................................................................1

Package Contents ..............................................................................................................1

Specfication........................................................................................................................1

LEDs...................................................................................................................................2

CHAPTER 2 INITIAL INSTALLATION..............................................................................5

Requirements.....................................................................................................................5

Procedure...........................................................................................................................5

CHAPTER 3 BOARD DESCRIPTION..................................................................................6

Components and connectors ............................................................................................6

Document Version: 1.0

All trademarks and trade names are the properties of their respective owners.

Chapter 1

Introduction

This Chapter provides an overview of the Home Monitoring Gateway's fea-

tures and capabilities.

Congratulations on the purchase of your new Home Monitoring Gateway. The Home Monitor-

ing Gateway is a consumer electronic device, which is used for home monitoring and security.

Package Contents

The following items should be included:

• The Home Monitoring Gateway Unit

• Power Adapter

• A Stand

If any of the above items are damaged or missing, please contact your dealer immediately.

Specfication

• DDR2 SDRAM 64MB

• NAND 32MB Flash

• Four Ethernet ports with RJ45 connectors.

• Front Panel LEDs

• Z-Wave module

• Two USB 2.0 ports

• Sync button

• WPS button

• Reset button

• Power In connector

• Two Internal antennae

• 802.11bgn Wireless Functions

LEDs

Front-mounted LEDs

The Home Monitoring Gateway has 8 LEDs.

Reset This button has two (2) functions:

• Reboot. When pressed and released, the 11N Home Monitoring

Gateway will reboot (restart).

• Clear All Data. This button can also be used to clear ALL data and

restore ALL settings to the factory default values.

To Clear All Data and restore the factory default values:

1. Power On.

2. Keep holding the Reset Button down for 8 seconds.

Release the Reset Button. The 11N Home Monitoring Gateway is now

using the factory default values.

WPS button Push the WPS button on the device and on your other wireless device to

perform WPS function that easily creates an encryption-secured wireless

connection automatically.

Sync Button Push this button to synchronize for portal server or Z-Wave clients.

POWER

(Green) • On - Power On

• Off - Power Off

• Flashing - Reboot or Firmware upgrade.

WAN (Green) • On - Connection to the Gateway attached to the WAN (Internet)

port is established.

• Off - No connection to the Gateway.

• Flashing - Data is being transmitted or received via the connection.

WiFi & WPS WiFi

• On (Green) - Wireless connection available

• Off (Green) - No Wireless connection available.

• Flashing (Green) - Data is being transmitted or received via the

Wireless connection.

WPS

• On (Amber) - Problem occurred while trying to enable the

WPS function.

• On (Green) - WPS function is enabled.

• Flashing - Data is being transmitted or received via the connection.

Service • On (Green)- Control Point has made a successful activation to the

Portal Server.

• Off - No active connection to the Portal Server.

• Flashing - Attempting to establish a connection to the Portal Server.

LAN (Green) • On (Green)- LAN connection established.

• Off - No active connection on the corresponding LAN port.

• Flashing - Data is being transmitted or received via the correspond-

ing LAN (hub) port.

ZWave • On - ZWave function enabled.

• Off - ZWave function disabled.

• Flashing - Data is being transmitted or received via the connection.

USB (1~2) • On (Green)- USB connection established.

• Off - No active connection on the corresponding USB port.

• Flashing - Data is being transmitted or received via the correspond-

ing USB port.

Rear Panel

WAN port

(10/100BaseT) Connect the DSL or Cable Modem here. If your modem came with a

cable, use the supplied cable. Otherwise, use a standard LAN cable.

LAN (1~4) Port Use standard LAN cables (RJ45 connectors) to connect your PCs to

these ports.

USB (1~2) Port The two connectors are USB hosts with support for mass storage

devices.

RS232/RS422

terminal The terminal block includes transmit (tx)/receive (rx) connections and a

GND port.

Power Port Connect the supplied power adapter here.

Chapter 2

Initial Installation

This Chapter covers the software installation of the Home Monitoring Gate-

way.

Requirements

• Network cables. Use standard 10/100BaseT network (UTP) cables with RJ45 connectors.

Procedure

1. Choose an Installation Site

Select a suitable place to install the Home Monitoring Gateway.

2. Connect LAN Cables

Use standard LAN cables to connect devices to the Ethernet ports on the Home Monitor-

ing Gateway.

4. Power Up

Connect the supplied power adapter to the Home Monitoring Gateway. Use only the

power adapter provided. Using a different one may cause hardware damage.

5. Check the LEDs

• The POWER LED should be ON.

• The LAN LED should be ON (provided the PC is also ON.)

Chapter 3

Board Description

This Chapter provides board description for the Home Monitoring Gateway.

Components and connectors

1 2 3 4

98765

• 1. RS422/RS232 connector

• 2. USB type A connector

• 3. LAN port

• 4. WAN port

• 5. Expansion slot connectors

• 6. Push buttons.

• 7. Console port

• 8. LEDs

• 9. RT3662 processor

• 10. RS422/RS232 function select jumper

• 11. DC power jack

Console port connection guide

For platform debugging, please locate the console cable accompanied with the development kit.

Then follow the steps illustrated below:

Pin definition

1. Connect cable to console port

2. Execute minicom on Linux host machine

3. Press Ctrl+A then Z to enter minicom configuration

4. Set Comm port to baud rate 57600, 8 data bits, no parity bits, and one stop bit.

Table des matières

Autres manuels Sercomm Porte

Sercomm

Sercomm NA900ZB Manuel utilisateur

Sercomm

Sercomm NA900B Manuel utilisateur

Sercomm

Sercomm NA301-ZB Manuel utilisateur

Sercomm

Sercomm NA301 Manuel utilisateur

Sercomm

Sercomm YN400 Manuel utilisateur

Sercomm

Sercomm NA910B Manuel utilisateur

Sercomm

Sercomm NA403 Manuel utilisateur

Sercomm

Sercomm DG4244 Manuel d'utilisation et d'entretien

Sercomm

Sercomm NA503S-4G Manuel utilisateur

Sercomm

Sercomm NA301ZW Manuel utilisateur

Sercomm

Sercomm NA502S-4G Manuel utilisateur

Sercomm

Sercomm NA502S Manuel utilisateur

Manuels Porte populaires d'autres marques

LST

LST M500RFE-AS Manuel utilisateur

Kinnex

Kinnex Media Gateway Manuel utilisateur

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur

Telsey

Telsey CPVA 500 - SIP Manuel utilisateur

RTA

RTA 460A-NNA4 Fiche technique

Shaw

Shaw Gateway HDPVR Manuel utilisateur

ABB

ABB VSN900 Guide de démarrage rapide

Commander

Commander Pulse Manuel utilisateur

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuel utilisateur

NETGEAR

NETGEAR C6300BD Manuel utilisateur

Amit

Amit CDW531AM Manuel utilisateur

HMS

HMS Netbiter EasyConnect EC150 Manuel utilisateur

Huawei

Huawei EchoLife HG620 Manuel utilisateur

AT&T

AT&T U-verse 3801 Manuel d'utilisation et d'entretien

Logic IO

Logic IO RTCU MX2 turbo Manuel utilisateur

Suttle

Suttle MediaMAX MXM-521 Manuel utilisateur