Sense Innoband SC00 Manuel utilisateur

Version 0.1

Innoband SC00

Innoband Sense Commander

(Z-Wave / Ethernet Wireless Gateway)

User Man al

Version 0.1

User Manual

Innoband SC00

Information in this document is subject to change without notice and does not represent a commitment on the

part of Innoband Technologies, Inc. The software described in this document is furnished under a license

agreement and may be used or copied only in accordance with the terms of the license agreement. It is against

the law to copy the software on any other medium except as specifically allowed in the license agreement. The

licensee may make one copy of the software for backup purposes. No part of this manual may be reproduced or

transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, for any

purpose without the written permission of Innoband Technologies, Inc.

Manual Version 0.1

January 2013

Innoband is a trademark of Innoband Technologies, Inc. The trademarks, logos and service marks (“Marks”)

displayed on this manual are the property of Innoband or other third parties. Users are not permitted to use these

Marks without the prior written consent of Innoband or such third party that may own the Mark. IBM is a

registered trademark of International Business Machines Corporation. Intel and Pentium are registered

trademarks of Intel Corporation. Microsoft, MS-DOS, Windows, and the Windows logo are registered trademarks

of Microsoft Corporation. All other products are trademarks or registered trademarks of their respective owners.

Table Content

Getting started...................................................................................................... 4

Unpacking.......................................................................................................... 4

Overview ........................................................................................................... 4

Specifications ..................................................................................................... 4

Physical Outlook ................................................................................................. 5

About -WaveTM ................................................................................................. 5

LED Descriptions (TBD) ....................................................................................... 6

Install your new device .......................................................................................... 7

Install the Hardware ........................................................................................... 7

Create User Account at Sense Cloud...................................................................... 7

Log Into Sense Commander ................................................................................. 8

Log Into Sense Cloud Server ...............................................................................11

Perform -WaveTM Device Inclusion......................................................................12

Perform -WaveTM Device Exclusion .....................................................................14

Using Sense Commander.......................................................................................15

PC Browser App .................................................................................................15

Run and Edit Scenes ..........................................................................................16

Define and Configure Triggers .............................................................................19

Android App ......................................................................................................21

Troubleshooting ...................................................................................................22

Certifications........................................................................................................23

FCC..................................................................................................................23

Warning ...........................................................................................................23

Warranty .............................................................................................................25

Contact information ..............................................................................................27

Getting started

Unpacking

Check the contents of the package against the pack contents checklist below. If any of the

items is missing, then contact the dealer from whom the equipment was purchased.

•Main Sense Commander Unit

•Mounting Screws (2x)

•Quick Start Guide

•AD/DC Power Adapter

•Ethernet Cable

Overview

Innoband's -Wave Sense Commander gateway connects to an Ethernet router to allow

users to control a -Wave based sensor network.

The sensor network may include -Wave security devices such as door/window sensors,

motion detectors, sirens, and door locks. The network may also includes home automation

and energy monitoring devices such as appliance on/off switches, light socket on/off

adapters, light dimmers, thermostats, and irrigation controller.

This Sense Commander is designed to control the -Wave devices when it's properly

connected to an Ethernet network. This Ethernet network can be a LAN (local area network)

or WAN (wide area network). Users can then access the WSN Controller through LAN or

WAN using web browsers on PCs, Mac's, tablets, or mobile devices such as smart phones.

Specifications

Model Name Innoband Sense Commander

Model No SC00

Part No 250-I-SC00-00

Power Adapter 12V DC/1A

Operating Frequency 908.42 MHz

Battery Type (Optional) AAA x 4

Operating Range Up to 30 meters line of sight (indoor)

Physical O tlook

Abo t Z-WaveTM

-WaveTM is a wireless communications protocol designed to remotely control applications in

residential and commercial environments.

Each -WaveTM network is identified by a Network ID, and each device is further identified

by a Node ID. A device must be "included" to the -WaveTM network before it can be

controlled via -WaveTM.

This ‘Inclusion” process (also known as "pairing" and "adding") is achieved by pressing a

sequence of buttons on the controller and the device being added to the network. This

sequence only needs to be performed once, after which the device is always recognized by

the controller. Devices can be removed from the -WaveTM network by a similar “Exclusion”

process of button strokes.

Summary:

F nction Description

Inclusion Add a -Wave device (e.g. Dimmer) to -Wave network

Exclusion Remove a -Wave device (e.g. Dimmer) from -Wave network

Reset Restore Sense Commander to factory default

1Inclusion Button 5USB Ports (reserved)

2Exclusion Button 6Ethernet Network Jack

3LED Indicators (x4) 7DC Power Jack

4Recessed Reset Button

Front View Top View Rear View

LED Descriptions (TBD)

The table below provides a summary of LED functions. Please refer to applicable user’s

guides on applicable -WaveTM devices for inclusion and exclusion procedures.

F nction Description LED & Siren Stat s

Power Indicate if the unit is properly

powered

LED: solid green

Ethernet Indicate if the unit is connected

to an Ethernet network

LED: blinking green

1. Configure the -Wave

Controller into inclusion mode.

2. Press the Inclusion button until

In/exclusion LED start to blink

in red.

3. The blinking LED stops if a -

Wave sensor is discovered and

paired with the Commander.

Inclusion

4. The inclusion mode times out

in 30 seconds if nothing is

discovered.

LED: blinking red

1. Configure the -Wave

Controller into exclusion mode.

2. Press the Exclusion button until

In/exclusion LED start to blink

in red.

3. The blinking LED stops if a -

Wave sensor is discovered and

excluded with the Commander.

Exclusion

4. The exclusion mode times out

in 30 seconds if nothing is

discovered.

LED: blinking red

-Wave Indicate if -Wave communication

is working properly.

LED: n/a

Install yo r new device

Innoband’s SC00 Sense Commander gateway is designed for dry indoor environment only.

Please follow these steps below to properly set up the unit.

Install the Hardware

1. Unpack Sense Commander from the package.

2. Use the supplied Ethernet cable and connect the Commander’s Network port to an

available port on the home network’s Ethernet Router.

3. Power on the Sense Commander using the supplied power adapter.

4. Wait about 60 seconds until the flashing red In/Exclusion LED goes off, and the

Power LED is solid green, while the Ethernet LED blinks in green steadily.

Create User Acco nt at Sense Clo d

1. If applicable, turn on a computer that is wire or wirelessly connected to the same

Ethernet router.

2. Launch a web browser (such as Internet Explorer, Google Chrome, Apple Safari,

FireFox) on the computer.

3. In the URL field, enter www.innobandsense.net.

4. On the Sign In page, select Create new account.

5. Follow the screen instructions, enter the desired email address, password, and

validation code and click ‘Authorize’.

6. An automated email will be sent to the email address entered earlier.

7. Retrieve the email (check your SPAM folder if necessary) and click on the validation

link in the email message.

Log Into Sense Commander

1. If applicable, turn on a computer that is wire or wirelessly connected to the same

Ethernet router.

2. Download the gateway discovery utility application at:

http://www.innobandsense.com/images/SenseDiscovery.rar or

http://www.innobandsense.com/images/SenseDiscovery.zip.

3. Open the downloaded file, run Setup.exe to install the application on the computer.

4. Upon completion, look for the “DiscoverUtility” program shortcut on the computer’s

desktop.

5. Launch the application by double clicking the desktop shortcut.

6. Click on the “Scan” button.

7. An IP address will be shown under “Gateway IP”. Make a note of the Gateway IP

address shown in the “Gateway List”.

8. Double click on the Gateway IP address.

9. A browser session will automatically be launched. (Alternatively, launch a web

browser (such as Internet Explorer, Google Chrome, Apple Safari, FireFox) on the

computer. In the URL field, enter the Gateway IP address found using the utility

above.)

10. When prompted, enter ‘admin’ as the User Name and leave the Password field blank,

and click on ‘Log In”.

11. You’re now accessing the web server inside the Commander’s flash memory.

12. Select “Configuration Devices”.

13. Select “WSN Controller”.

14. Select “Gateway Setting”.

15. Click the “Reset” button and proceed with resetting the gateway. Wait until it’s

completed.

16. Click on the “Gateway Setting” tab.

17. Replace the default account and password with the New Account created earlier at

www.innobandsense.net. Click ‘Save’, and then ‘Exit’.

18. Go back to the Device / System Setup, and click the WSN Controller tab.

19. Click ‘Log off’.

Table des matières

Autres manuels Sense Porte

Sense

Sense SG-2440pfSense Manuel utilisateur

Manuels Porte populaires d'autres marques

LST

LST M500RFE-AS Manuel utilisateur

Kinnex

Kinnex Media Gateway Manuel utilisateur

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuel utilisateur

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur

Telsey

Telsey CPVA 500 - SIP Manuel utilisateur

RTA

RTA 460A-NNA4 Fiche technique

Shaw

Shaw Gateway HDPVR Manuel utilisateur

ABB

ABB VSN900 Guide de démarrage rapide

Commander

Commander Pulse Manuel utilisateur

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuel utilisateur

NETGEAR

NETGEAR C6300BD Manuel utilisateur

Amit

Amit CDW531AM Manuel utilisateur

HMS

HMS Netbiter EasyConnect EC150 Manuel utilisateur

Huawei

Huawei EchoLife HG620 Manuel utilisateur

AT&T

AT&T U-verse 3801 Manuel d'utilisation et d'entretien

Logic IO

Logic IO RTCU MX2 turbo Manuel utilisateur

Suttle

Suttle MediaMAX MXM-521 Manuel utilisateur