Seneca R-32DIDO Manuel utilisateur

MI00596-0-EN INSTALLATION MANUAL 1/4

INSTALLATION MANUAL

SENECA s.r.l.; Via Austria, 26 – 35127 – PADOVA – ITALY; Tel. +39.049.8705359 - Fax +39.049.8706287

WARNING: The full content of this manual must be read before any operation. The module must only be used by

qualied electricians. Specic documentation is available via QR-CODE shown on page 1.

Electrical and electronic waste disposal (applicable in the European Union and other countries with recycling).

The symbol on the product or its packaging shows the product must be surrendered to a collection centre

authorized to recycle electrical and electronic waste.

The module must be repaired and damaged parts replaced by the Manufacturer. The product is sensitive to

electrostatic discharges. Take appropriate measures during any operation.

PRELIMINARY WARNINGS

The word WARNING preceded by the symbol indicates conditions or actions that put the user's safety at risk.

The word ATTENTION preceded by the symbol indicates conditions or actions that might damage the

instrument or the connected equipment. The warranty shall become null and void in the event of improper use or

tampering with the module or devices supplied by the manufacturer as necessary for its correct operation, and if

the instructions contained in this manual are not followed.

CONTACT INFORMATION

Technical support [email protected] Product information [email protected]

This document is the property of SENECA srl. Copies and reproduction are prohibited unless authorised.

The content of this document corresponds to the described products and technologies.

Stated data may be modied or supplemented for technical and/or sales purposes.

R-32DIDO

R-32DIDO-P

DOCUMENTATION

R-32DIDO

DOCUMENTATION

R-32DIDO-P

MI00596-0-EN INSTALLATION MANUAL 2/4

MODULE LAYOUT

Weight: 170 g; Enclosure: UL94-V0 self-extinguishing PC/ABS material, black.

LED STATUS LED meaning

PWR On Device powered

Off Device not powered

IO1/IO32 On Digital input/output active

Off Digital input/output not active

OUT

SUP

On Digital inputs/outputs powered

Off Digital inputs/outputs not powered

STS

(Status)

On IP address set

Flashing Waiting for the IP address from the DHCP

COM

(R-32DIDO-P version only)

Off No Pronet communication

Flashing Pronet communication present

FAIL On Digital output in FAIL

Off Digital output OK

(R-32DIDO version only)

On RS485 port wiring error

Flashing Reception of data packet completed on RS485

(R-32DIDO version only) Flashing Transmission of data packet completed on RS485

ETH TRF (Yellow) Flashing Packet transit on Ethernet port

ETH LNK (Green) Flashing The Ethernet port is connected (LINK)

SIGNALS VIA LED ON FRONT PANEL

CERTIFICATIONS

https://www.seneca.it/products/r-32dido/doc/CE_declaration

TECHNICAL SPECIFICATIONS

32.2 mm

0.09

106.6 mm

MI00596-0-EN INSTALLATION MANUAL 3/4

INSULATION

POWER SUPPLY Voltage: 10÷40Vdc; 19÷28Vac; 50÷65Hz; Absorption: 3W max; Dissipation: 6.5W max

ENVIRONMENTAL

CONDITIONS

Operating temperature: from -25°C to +65°C

Humidity: 10% ÷ 90% non condensing.

Storage temperature: from -30°C to +85°C

Protection rating: IP20

CONFIGURATION With integrated WEB Server

CONNECTIONS/

COMMUNICATION

PORTS

3.5 mm pitch terminal block, 1.5 mm2 max cable section

1 Ethernet (with LAN fault-bypass function) 100 base T on RJ45 (R-32DIDO-1 model)

2 Ethernet (with LAN fault-bypass function) 100 base T on RJ45 (R-32DIDO-2 model)

1 RS485 port on terminals 23-24-25 (only R-32DIDO-1/ R-32DIDO-2 versions)

DIGITAL INPUTS

Number of channels: 32; Voltage: Threshold ON: >9V; Threshold OFF: < 4 V; Vmax: 24 V;

Impedance 9kΩ

Individually congurable

DIGITAL OUTPUTS Number of channels: 32, MOSFET, PNP; Max voltage/current: 0.2 A / 24 V

Individually congurable

COUNTERS: Number of counters: 32 at 32 bit, maximum speed: 50 Hz

....

64+

65-

LOAD

12/24V

18+

19-

ELECTRICAL CONNECTIONS

–/

+ /

23 B(-)

24 A(+)

25 GND

POWER SUPPLY RS485 SERIAL PORT

The power supply must be sized according to the expected load at the outputs. Terminals 18-64 and 19-65 can be connected

together on the same power supply.

*For correct instrument operation, power the I/Os via the I/O Ext Supply 1 and 2 terminals at the same time.

DIGITAL INPUTS (PNP)

Inputs from 9 to 32

DIGITAL INPUTS (PNP)

Inputs from 1 to 8

DIGITAL OUTPUTS (PNP)

Outputs from 9 to 32

DIGITAL OUTPUTS (PNP)

Outputs from 1 to 8

The upper power supply limits must not be exceeded, as this could cause serious damage to the module.

Switch the module off before connecting inputs and outputs.

To meet the electromagnetic immunity requirements:

- use shielded signal cables;

- connect the shield to a preferential instrumentation earth system;

- separate shielded cables from other cables used for power installations (transformers, inverters, motors, etc.).

CAUTION

Connection to the RS485 port.

Polarity is not standardised; in some devices of other brands it

may be inverted.

PWR

1500 Vac

DIGITAL

INPUT/OUTPUT

USB

RS485

ETH1

PORT1

ETH2

PORT2

PWR AUX

*** *

....

18+

19-

12/24V

64+

65-

....

64+

65-

12/24V

18+

19-

....

18+

19-

LOAD

12/24V

64+

65-

MI00596-0-EN INSTALLATION MANUAL 4/4

DAISY-CHAIN (R-32DIDO-2 / R-32DIDO-2-P ONLY)

IT IS NOT ALLOWED TO CREATE LOOPS WITH ETHERNET CABLES

Using the daisy-chain connection it is not necessary to use switches to connect the devices.

The following examples show the correct connections.

There must be no loops in the Ethernet cabling, otherwise the communication will not work. The modules and switches must be

connected eliminating any loops. The following examples show the incorrect connections.

The LAN fault-bypass function allows you to keep the connection between the two Ethernet ports of the device ON, in the event of a

power failure. If a device turns off, the chain is not interrupted and the devices downstream of the switched-off one will still be acces-

sible. This function has a limited duration: the connection remains active for a few days, typically 4. The fault-bypass function requires

that the sum of the lengths of the two cables connected to the switched off module is less than 100m.

MODULE 1 MODULE 2 MODULE 3

ETHERNET CONNECTION RULES

For the Ethernet cabling between the devices, the use of the unshielded CAT5 or CAT5e cable is required.

CAT6 for industrial environments.

FACTORY IP ADDRESS

The default module IP address is static: 192. 168. 90. 101

WEB SERVER

To access the maintenance Web Server with the 192.168.90.101 factory IP address

(Default user: admin; Default password: admin) http://192.168.90.101

DO NOT USE DEVICES WITH THE SAME IP ADDRESS IN THE SAME ETHERNET NETWORK.

MODULE 1 MODULE 2

LOOP

MODULE 3

MODULE 1

LOOP

DIP- SWITCH SW1: through DIP-SWITCH-SW1 it is possible to set the IP conguration of the device:

DESCRIPTION DIP 1 DIP 2

To obtain the conguration from the Flash memory, both SW1 DIP

switch selectors must be set to OFF

To reset the device to factory settings both SW1 DIP switches must

be set to ON

To force the device's IP address to the standard value of SENECA

Ethernet products: 192.168.90.101

Reserved

DIP - SWITCH SETTINGS

The DIP-switch settings are read only at boot time. At each change, perform a restart.

DIP-SWITCHES are located on the back of the device.

To access the DIP-SWITCH it is necessary to remove the bottom of the instrument.

CAUTION

WARNING

Autres manuels pour R-32DIDO

Ce manuel convient aux modèles suivants

Autres manuels Seneca Unité de contrôle

Seneca

Seneca Z-4TC Manuel utilisateur

Seneca

Seneca Z-PC SERIES Manuel utilisateur

Seneca

Seneca Z113S Manuel utilisateur

Seneca

Seneca Z109REG2 Manuel utilisateur

Seneca

Seneca Z-4DI-2AI-2DO Manuel utilisateur

Seneca

Seneca Z-8AI Manuel utilisateur

Seneca

Seneca 85389091 Manuel utilisateur

Seneca

Seneca Z-8TC-LAB Manuel utilisateur

Seneca

Seneca Z-LINK1-LO Manuel utilisateur

Seneca

Seneca Z Series Manuel utilisateur

Seneca

Seneca Z-PASS1 Manuel utilisateur

Seneca

Seneca MyAlarm3 Cloud Manuel utilisateur

Seneca

Seneca R-8AI-8DIDO-P Manuel utilisateur

Seneca

Seneca MyBoat-WR Manuel utilisateur

Seneca

Seneca Z-TWS11 Manuel utilisateur

Seneca

Seneca Z-8AI Manuel utilisateur

Seneca

Seneca Z Series Manuel utilisateur

Seneca

Seneca VPN BOX 2 Manuel utilisateur

Seneca

Seneca Z-PC Z-TWS5 Manuel utilisateur

Seneca

Seneca Z-PC SERIES Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur