Segway I180 Mode d’emploi

WARNING!

Always shut down your Segway HT and unplug the Power Cord before performing any

maintenance or installing any part or accessory.

Follow these instructions carefully. Failure to follow these instructions could damage your

Segway HT and render it unsafe to use.

Questions?

If you have any questions or are missing a part, please contact an Authorized Segway

Dealer. For a list of Dealers, visit www.segway.com. Check www.segway.com for

updates to these instructions. Thank you.

Segway

Human Transporter (HT)

Splash Guard Replacement Instructions

i180 Model Fenders

LIMITED WARRANTY

The Segway HT Splash Guards are an “Accessory” covered for 90 days under the Segway®Human

Transporter Limited Warranty (copy delivered with the kit.)

Contents

> (2) Splash Guards

> (4) Fender Tabs

> (4) T-20 Drive Fender Fasteners

Note: Replace any fasteners you remove

with the new fasteners included in this kit.

Tools Required

> 16 mm deep socket

> 50 N-m Torque Wrench to accommodate

the 16 mm deep socket

> Rubber Mallet

> T-20 Six-Lobe bit (Torx T-20)

> 1.5 N-m Torque Wrench to

accommodate the Six-Lobe bit

Product Information

> Impact-resistant construction

> Identical/interchangeable for left/right

side and all 3 positions along the fender

Splash Guards

Wheel Insert Replacement Instructions

Fender Tab

Remove the Tire/Wheel Assembly

Step 1 Tip the Segway HT onto its side so

that the outside of one wheel lays flat

against a clean, smooth surface

Step 2 Remove the Wheel Nut with a 16 mm

deep socket wrench. Hold the wheel

from rotating and turn the wrench

counterclockwise. (This may require

considerable force.)

Step 3 Strike the outside edge of the tire with

a rubber mallet to unseat the wheel

hub taper. (This may require multiple

attempts as the wheel hub is seated

tightly into the Gearbox taper.)

Step 4 Lift off the wheel.

Step 5 Clean any debris from inside of

Gearbox taper and outside of wheel

hub.

Remove the Splash Guard

Step 1 Remove the two Splash Guard

fasteners using a T-20 six-lobed bit

(Torx T-20).

Step 2 Remove the two oblong Fender Tabs

that are between the fasteners and

the Fender, and save these for reuse

when you install the Splash Guards.

Step 3 Remove the Splash Guard

Wheel Insert Replacement Instructions

Install the Splash Guard

Step 4 Position the Splash Guard into the

position you select on the Fender.

(For best spray protection, install the

Splash Guard in the rear position.)

Step 5 Hold the two Fender Tabs in the slots

in the Fender, and thread the two

fasteners through the Fender Tabs

and Fender and into the Splash

Guard.

Step 6 Torque to 1.5 N-m using a T-20 six-

lobed bit (Torx T-20). Over tightening

could strip aluminum threads.

Reseat the Tire/Wheel Assembly

Step 1 Place the Wheel hub opening over

the Gearbox drive shaft; rotate the

wheel while pressing down until the

wheel seats.

Step 2 Thread on the wheel nut and tighten

with the socket wrench.

Step 3 Torque to 50.0 N-m.

We hope this document provided clear step-by-step instructions. If you feel these instructions

are incorrect in any way, we would like to hear from you. Please contact Segway Customer

Support at 1-866-4SEGWAY (1-866-473-4929) or go to www.segway.com if you have any

questions, comments or suggestions. Thank you!

Table des matières

Autres manuels Segway Scooter

Segway

Segway Ninebot KickScooter Manuel utilisateur

Segway

Segway i2 SE Manuel utilisateur

Segway

Segway Ninebot KickScooter Manuel utilisateur

Segway

Segway E300SE Manuel utilisateur

Segway

Segway eMoped B Series Manuel utilisateur

Segway

Segway Ninebot KickScooter Manuel utilisateur

Segway

Segway KickScooter P100SE Manuel utilisateur

Segway

Segway Ninebot eKickScooter Manuel utilisateur

Segway

Segway Ninebot KickScooter F2 E Manuel utilisateur

Segway

Segway Ninebot ES Series Manuel utilisateur

Segway

Segway Ninebot KickScooter Manuel utilisateur

Segway

Segway P65E Manuel utilisateur

Segway

Segway miniplus N4M350 Manuel utilisateur

Segway

Segway i2 Patroller Manuel utilisateur

Segway

Segway Steering Grip Kit Guide de référence

Segway

Segway i2 SE Manuel utilisateur

Segway

Segway x2 Turf Manuel d'utilisation

Segway

Segway eMoped C80 Manuel utilisateur

Segway

Segway D18E Manuel utilisateur

Segway

Segway Ninebot KickScooter Manuel utilisateur

Segway

Segway Ninebot KickScooter MAX G30LE Manuel utilisateur

Segway

Segway Ninebot D18W Manuel utilisateur

Segway

Segway NINEBOT ONE S2 Manuel utilisateur

Segway

Segway Ninebot KickScooter Manuel utilisateur

Manuels Scooter populaires d'autres marques

TEKTRO

TEKTRO CHEETAH Manuel utilisateur

Douglas

Douglas Vespa Sprint Guide d'installation

PLAYTIVE

PLAYTIVE AS-2448 Manuel utilisateur

Ebinger

Ebinger DONKEY XL Manuel utilisateur

Flyer

Flyer Mountain Guide de l'utilisateur

BackCountry eBikes

BackCountry eBikes Storm Manuel utilisateur

equipmed

equipmed FreeRoam II Manuel utilisateur

Yoto

Yoto Lion Manuel utilisateur

WESTHILL BIKES

WESTHILL BIKES LINK Manuel utilisateur

BAnff

BAnff eProdigy series Manuel utilisateur

Winther

Winther 475 Manuel utilisateur

Jetson

Jetson JBZL17 Manuel utilisateur

First Choice Mobility

First Choice Mobility Roma Medical Corella S741 Manuel utilisateur

Carrera

Carrera impel Manuel utilisateur

Afikim

Afikim Superlight SL-3 Manuel utilisateur

CareCo

CareCo ZOOM Manuel utilisateur

Douglas

Douglas Vespa G.S. Manuel utilisateur

Gazelle

Gazelle with BOSCH System Manuel utilisateur

Segway i180 Mode d’emploi

Manuels Scooter populaires d'autres marques