Segway 1689500001 Guide de référence

Customer Installable Parts

Upper Cargo Structure & Bag

e Series and i Series Models Only

Kit Number: 1689500001 Contents

·1 handlebar bag

·1 bag lid

·1 wire mounting frame

·1 control shaft clamp

·1 clamp screw

·2 button head screws

Specifications

·10 lb. maximum carrying capacity

·Polypropylene and polyethylene construction

·Polyester and mesh soft-sided pockets with cord locks

·Stainless steel snaps on bag lid

·Hook and loop attachment straps

·Powder-coated stainless steel wire mounting frame

Tools Required

·2.5mm hex wrench

·4mm hex wrench

WARNING

Always shut down your Segway HT and unplug the charge cord before performing any maintenance or installing any part or

accessory.

Follow these instructions carefully. Failure to follow these instructions carefully could damage your Segway HT and render it

unsafe to use.

Before you begin:

Do not use the parking stand to support the Segway HT while performing this procedure. The parking stand

is not designed to withstand the forces that may be generated. Instead, lay the Segway HT down on its back

side or support it with other objects so that you have easy access to the front of the handlebar and control

shaft.

Installation

Step 1

If present, remove the two button head

screws located on the bottom of the

handlebar using a 4mm hex wrench.

Step 2

Align the holes in the wire frame with the

screw locations in the bottom of the

handlebar so that the frame is on the front

side of the control shaft.

Step 3

Install the two button head screws through

the holes in the wire frame and into the

bottom of the handlebar using a 4mm hex

wrench and torque to 7.5 N-m.

Step 4

Install the clamp on the control shaft just

above the height adjustment collar with the

hook facing forward and up.

Note

Replace any fasteners you remove when performing this

installation with the new fasteners included in this kit .

Step 5

Slide the clamp up to the wire frame so that the wire frame rests in the hook.

Step 6

Install the clamp screw and with a 2.5mm hex wrench torque to 1.5 N-m. (The gap between the halves of the

clamp should be about 4mm.)

Step 7

Lightly tap the wire frame so that it snaps in the hook of the clamp.

Step 8

Drape the cargo bag over the handlebar so that the Display and Key Port are not obstructed.

Step 9

Secure the hook and loop straps around the wire frame at the bottom and sides of the bag.

LIMITED WARRANTY The Segway HT Upper Cargo Structure and Bag is an accessory covered by the SegwayTM

Human Transporter Limited Warranty (copy delivered with this kit).

Questions?

If you are missing a part, or if you need to return the product please contact Segway Customer

Service at 866.4SEGWAY (866.473.4929) or on our website at

www.segway.com/support/contact_us.html.

Table des matières

Autres manuels Segway Scooter

Segway

Segway NINEBOT ONE S2 Manuel utilisateur

Segway

Segway KickScooter Manuel utilisateur

Segway

Segway Ninebot KickScooter Manuel utilisateur

Segway

Segway i2 SE Manuel utilisateur

Segway

Segway GT1A Manuel utilisateur

Segway

Segway SE-3 Patroller Manuel utilisateur

Segway

Segway Ninebot KickScooter Air T15E Manuel utilisateur

Segway

Segway Ninebot KickScooter Manuel utilisateur

Segway

Segway G30D Manuel utilisateur

Segway

Segway Ninebot KickScooter ES1L Manuel utilisateur

Segway

Segway Personal Transporter i2 Manuel d'utilisation et d'entretien

Segway

Segway Ninebot ES Series Manuel utilisateur

Segway

Segway i Series Manuel utilisateur

Segway

Segway NINEBOT ONE S1 Manuel utilisateur

Segway

Segway D18E Manuel utilisateur

Segway

Segway KickScooter Manuel utilisateur

Segway

Segway NINEBOT MINIPRO Manuel utilisateur

Segway

Segway Ninebot Mecha Kit Manuel utilisateur

Segway

Segway GT Manuel utilisateur

Segway

Segway Ninebot KickScooter Air T15 Manuel utilisateur

Segway

Segway NEB1002-H1 Manuel utilisateur

Segway

Segway Ninebot KickScooter F30 Manuel d'utilisation

Segway

Segway Ninebot KickScooter Manuel utilisateur

Segway

Segway Ninebot KickScooter Manuel utilisateur

Manuels Scooter populaires d'autres marques

TEKTRO

TEKTRO CHEETAH Manuel utilisateur

Douglas

Douglas Vespa Sprint Guide d'installation

PLAYTIVE

PLAYTIVE AS-2448 Manuel utilisateur

Ebinger

Ebinger DONKEY XL Manuel utilisateur

Flyer

Flyer Mountain Guide de l'utilisateur

BackCountry eBikes

BackCountry eBikes Storm Manuel utilisateur

equipmed

equipmed FreeRoam II Manuel utilisateur

Yoto

Yoto Lion Manuel utilisateur

WESTHILL BIKES

WESTHILL BIKES LINK Manuel utilisateur

BAnff

BAnff eProdigy series Manuel utilisateur

Winther

Winther 475 Manuel utilisateur

Jetson

Jetson JBZL17 Manuel utilisateur

First Choice Mobility

First Choice Mobility Roma Medical Corella S741 Manuel utilisateur

Carrera

Carrera impel Manuel utilisateur

Afikim

Afikim Superlight SL-3 Manuel utilisateur

CareCo

CareCo ZOOM Manuel utilisateur

Douglas

Douglas Vespa G.S. Manuel utilisateur

Gazelle

Gazelle with BOSCH System Manuel utilisateur