Force code change (#17) Master
When a new Manager or User code is added to the lock,
or a code is reset, the system can require that on first use,
the code holder must change their code. By default, force
change is set to being disabled.
• Enter #17
• Enter the Master ID and code
• Press 1 to enable force code change or 0 to disable it.
• Press Enter. If accepted, the lock will signal 3 green
flashes + 3 short beeps ☼☼☼
Example to enable force code change:
Enable or disable Duress (#14) Master
The Duress feature allows a coerced user to Enter a
special variant of their code which opens the lock, and also
generates a silent signal to notify others that safe is being
opened under duress. Connection to an alarm system and
peripheral equipment sold separately is required. Duress
is disable by default.
• Enter #14
• Enter the Master ID and code
• Press 1 to enable duress or 0 to disable it.
• Press Enter. If accepted, the lock will signal 3 green
flashes + 3 short beeps ☼☼☼
Example to enable duress:
A duress code is the user’s normal code with the last digit increased or decreased by 1.
For example, 01-123456 would become 01-123455 or 01-123457. If the normal code ends
with a 0, it can be changed to 9 or 1. If the normal code ends with a 9, it can be changed to
8 or 0.
Specify alarm input setting (#16) Master
With connection to an alarm system and peripheral
equipment sold separately, an alarm input signal can alter
the lock’s operation with one of the settings below:
Input signal remote blocks (Prevents the lock
from being opened)
Input signal overrides time delay
Input signal overrides dual mode
Alarm input signals are ignored by default
• Enter #16
• Enter the Master ID and code
• Press 0, 1, 2 or 3 as required
• Press Enter. If accepted, the lock will signal 3 green
flashes + 3 short beeps ☼☼☼
Example to set remote block:
Audit Master, Manager, User
With licensed software and peripheral equipment sold
separately, an audit of the last 500 lock events can be
downloaded. The audit is stamped with time and date
information based on the clock time of the keypad, as such
it is vital to ensure correct clock time, with annual
updates.
Full instructions to take audit are available on our website.
PC link must be activated using the keypad to start
communication with the software.
Activate PC Link (#30) Authorised Users
To start communication with LA GARD 700 Series
software, PC Link must be activated.
• Enter #30
• Enter a valid ID and code
• Press Enter. If accepted, the lock will signal 3 green
flashes + short beeps ☼☼☼, and the red light will stay
on ☼→
Example to activate PC link:
Manage the Manager Master
In 702 locks supplied by Safelock Systems Ltd, a Manager
is installed with ID 01. To manage the Manager, the
process is the same as for users but only the Master code
is valid to perform the command.
Reset Manager code (#57) Master
If the Manager has forgotten their code, it is possible to
reset it rather than deleting and adding the Manager again.
• Enter #57
• Enter the Master ID and code
• Enter the current ID (Normally 01) and new code twice
• Press Enter. If accepted, the lock will signal 3 green
flashes + short beeps ☼☼☼
Example to reset the Manager code:
Delete Manager (#56) Master
• Enter #56
• Enter the Master ID and code
• Enter the ID to be deleted (Normally 01)
• Press Enter. If accepted, the lock will signal 3 green
flashes + short beeps ☼☼☼
Example to delete the Manager:
CURRE NT
ID + NEW
Code
MASTER
ID + Code
CURRE NT
ID + NEW
Code
MASTER
ID + Code
CURRE NT
ID + NEW
Code
MASTER
ID + Code
CURRE NT
ID + NEW
Code
CURRE NT
ID + NEW
Code
NEW
ID + Code
ID
+
Code
CURRE NT
ID + NEW
Code
MASTER
ID + Code
CURRE NT
ID + NEW
Code
MASTER
ID + Code
CURRE NT
ID + NEW
Code
CURRE NT
ID + NEW
Code
NEW
ID + Code
