Secure SSP 302 Mode d'emploi
SSP 302
Socket Energy Monitor
User and Installation
Instructions
BGX501-921-01
out of range
controller cannot
communicate directly
with device
SSP Repeater
Z-Wave
Controller
Lamp Load
Secure SSP 302
Socket Energy Monitor
The Secure SSP 302 forms part of
a Z-Wave Plus™ home automation
network.
SSP 302 is a mains-powered,
plug-in device that supports energy
monitoring. It is suitable for
switching loads up to 3kW at 230V
AC. It can measure voltage,
Button
FLASH
current, power, energy etc. The
SSP 302 acts as a repeater in a
Z-Wave network and helps other
device messages to reach a
destination.
SSP 302 is a fully compliant
Z-Wave Plus™ device that will
work with other manufacturer’s
Z-Wave devices.
Installation
Step 1:
Unpack and
insert the
SSP 302 into
the wall socket.
Ensure that the
red-coloured
network status
3
LED is flashing (once per second).
Note:
If the network status LED is not
flashing check the following.
•Ensure wall socket switch is on.
•Press the top button, the relay
status LED should switch ON
and glow green.
•If the relay status LED does not
glow then the device is not
functioning.
•It is possible that the SSP 302
was part (joined) of another
network previously; if so, exclude
it before including it in this
network. Refer to step-2 for the
exclusion process.
Avoid locations alongside or behind
large metal surfaces that could
interfere with the low power radio
signals between the unit and the
controller.
Step-2: Z-Wave Plus™
commissioning
To include the
SSP 302 onto
a network, put the
controller into
inclusion mode.
Now, press and
hold the button on
SSP 302 for 4 to 7
seconds then
release. The network
FLASH
FLASH
5
status LED will start flashing (twice
per second) on successful start of
inclusion process.
Note: Refer to the controller’s
manual for controller relevant
actions.
On successful inclusion the LED
will turn off.
The total process can take up to 20
seconds (Refer to the “Technical
specifications – Radio” section for
details).
If the device fails to join the
network it will go back to factory
default state and the Network
status LED will start flashing once
per second.
If there is an issue with RF
Communication, then re-locate the
device and repeat the
commissioning process again.
To exclude the SSP 302 from a
network, put the controller into
exclusion mode (refer to controller
instructions) and follow the same
sequence as per the
commissioning process for include
node. After successful exclusion
the network status LED will start
flashing once per second, and the
device will reset to factory default.
If exclusion fails, SSP 302 network
status LED will turn off after about
5 seconds.
7
Note: Exclusion works when the
device is in direct range with the
controller (no repeater allowed).
Associating SSP 302 in a
Z-Wave Network
(follow steps 3 to 5)
Note: Association process works
only after device included onto
network.
Step 3: Put the controller into
Association Mode.
Note: Some controllers can
automatically associate. Always
check with the manufacturer’s
manual.
Step 4: Press and hold the
SSP 302 button for more than 1
second, but less than 4 seconds,
and then release.
Step 5: The controller will confirm
association when the process is
successfully completed.
9
Combined
Button & LEDs
Green LED: ON
power switched to
front socket
Green
LED
*Socket type
will vary with
country
Appliance Socket
Press the SSP 302 button (less
than one second) to supply power
to its socket. By default, the green
LED will be lit when the supply is
On.
Table des matières
Autres manuels Secure Instrument de mesure
Secure
Secure Liberty EG4v12 Manuel d'utilisation
Secure
Secure PADS-2 Manuel utilisateur
Secure
Secure Premier 211 Manuel utilisateur
Secure
Secure Liberty 100 Manuel utilisateur
Secure
Secure Elite 440 Manuel utilisateur
Secure
Secure Premier 300 Manuel utilisateur
Secure
Secure BGX501-806-R02 Manuel utilisateur
Secure
Secure Liberty 100 Manuel du produit
Secure
Secure TRACKSO ELITE 103-2 Manuel utilisateur
Secure
Secure Sprint 211 Manuel utilisateur
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur