Securakey Radio Key 600e Manuel utilisateur

Radio Key® 600e

STAND ALONE PROXIMITY ACCESS CONTROL SYSTEM

with PATENTED*

DYNASCAN® TECHNOLOGY

Operating & Installation Guide

Rev. G

www.SecuraKeyStore.com

(800) 878-7829

[email protected]

P/N 3321490

*Patent # 6317027

SOUNDCRAFT, INC.

Radio Key® 600e

Operating & Installation Guide

Table of Contents

Introduction .............................................................................................. 1

RK-PD1 Program Deck & RK-HHP Hand-Held Programmer. ................. 3

Programming Radio Key® 600e .............................................................. 4

Programming Hints .................................................................................. 8

Basic Operation ...................................................................................... 8

System Conﬁguration .............................................................................. 9

Wiring ..................................................................................................... 10

Power ..................................................................................................... 12

Installation .............................................................................................. 15

Troubleshooting ...................................................................................... 18

Returning a Unit ..................................................................................... 18

Ordering Additional Transponders .......................................................... 18

Warranty ................................................................................................. 18

Specifications ......................................................................................... 19

FCC Certification .................................................................................... 20

Illustrations

Figure 1, RK600e Components ............................................................... 2

Figure 2, MOV Wiring Diagram ...............................................................11

Figure 3, Wiring Diagram ....................................................................... 13

Figure 4, Basic Installation ..................................................................... 16

Figure 5, Wall Mounting on Metal Surface with Optional Spacer ........... 17

Figure 6, Post/Flange Mounting ............................................................. 17

Tables

Table 1, Cable Types and Distances ...................................................... 10

Table 2, Connector P1 Color Coding ..................................................... 14

Table 3, Connector P2 Color Coding ..................................................... 14

V031008 7011

THIS PAGE INTENTIONALLY LEFT BLANK

Radio Key® 600e Operating & Installation

Secura Key  1

INTRODUCTION

The Radio Key® 600e is a programmable single-door access control system

which controls access for up to 600 users. It can control an electric strike,

magnetic lock, or gate operator, and has an additional input for an exit switch

and output contacts for external alarm shunting. The major components

are shown in Figure 1.

The RK600e Access Control Unit contains the CPU, memory, access

relay, and an internal reader. It has a beeper, and a bi-color LED indicator.

An RK-HHP Hand-held Programmer or the RK-PD1 Program Deck (not

included), is used to add or delete transponders, to set the operating mode,

to program the password and latch timer. The RK600e is weather resistant

and is provided with a gasket for exterior installation.

Parts Supplied:

Access Control Unit

Gasket

MOV

Mounting Plate

Connector/Wire Pigtail

Operating Manual

Quick Start Guide and Wallet Sized Guide

User Log Form

2, 6-32 x 1/2” mounting screws

1, 4-40 x 5/16” Phillips housing screw

1, 4-40 x 5/16” Hex Socket, security housing screw

The RKAR Auxiliary Reader is optional, but recommended for extreme

weather or higher security applications. This reader parallels the internal

reader in the RK600e. It contains a bi-color LED indicator and a beeper also

driven by the RK600e. A gasket is provided for exterior installation.

The RKAT Audit Trail Module is optional and allows the RK600e to connect

to a PC or Printer for Audit Trail Reporting and programming. RK-LINKTM

Software for Windows® is included.

RK-PS, a 12VDC plug-in power supply is optional. It is designed to power

the RK600e only, and requires 120 VAC input. RK600-BB Back Box / Spacer

is optional. It extends the RK600e out from the mounting surface and pro-

vides additional room for wiring.

Radio Key® 600e Operating & Installation

Secura Key  2

RK600e Unit Programming Deck

Mounting Plate RK600-BB

Back Box/ Spacer

(optional)

Figure 1 - RK600e Components

Radio Key® 600e Operating & Installation

Secura Key  3

PROGRAMMING RADIO KEY® 600e

Radio Key® Transponders (Key Tags) are pre-encoded and engraved at the

factory with unique Transponder ID numbers. Because these numbers are

unique, Facility Codes (Site Codes) are not required.

Transponder ID Numbers are not pre-programmed into the Radio Key®

600E; you must add them to the system as described below.

Radio Key® 600E allows you to assign a Transponder to each User Number

(1 - 600) for programming purposes. The User Number is associated with

the individual person using the transponder.

Be sure to record the User Number, the Transponder ID Number and

the user’s name, and keep this information in a secure place. A blank

User Log Form has been included for this purpose. Do not write on this

form; use it as a photocopy master.

Because a new Transponder ID Number can be assigned to any available

User Number, the reader always has capacity to store 600 Transponders,

even after many Transponders have been voided from the reader.

The Program Deck & Hand-Held Programmer

The RK-PD1 Program Deck or the RK-HHP are used to program your

Radio Key® 600e. Presenting program cards to the Radio Key® RK-600e

is equivalent to pressing keys on the RK-HHP hand-held programmer. The

RK-PD1 consists of the 16 following cards:

ENTER

“0” ZERO

“1” ONE

“2” TWO

“3” THREE

“4” FOUR

“5” FIVE

“6” SIX

“7” SEVEN

“8” EIGHT

“9” NINE

“*” THRU

“+” VALID

“–” VOID

SET TIMER

MODE Hand-Held Programmer

(RK-HHP)

Radio Key® 600e Operating & Installation

Secura Key  4

(Password) (ENTER)

Presenting these cards to the RK-600e is equivalent to pressing keys on

a Keypad or key board. As you present program cards to the unit, it will

chirp to indicate that it has read the card. The next sections of this manual

explain what program card sequences to use to perform the various program

functions.

PROGRAMMING STEPS

To program the Radio Key® 600e, you must ﬁrst enter the program mode as

described in the next section below. Once in the program mode, the LED

will blink amber as an indicator. The unit will remain in the program mode

until it is put into another mode. Also, if a program card is not presented for

15 seconds, the unit will return to the active mode.

After you have completed a proper program sequence, the unit will beep

and the LED will ﬂash green to indicate that the program instruction has

been accepted. A red light and three beeps at the end of a programming

sequence means that you have made an error. Refer to the appropriate

section, and carefully re-enter the command in the proper sequence.

If you select a User Number for a new Transponder, and a Transponder ID

Number has already been stored in memory for that User Number, a red light and

three beeps will occur. Select another User Number or void the User Number,

which removes the previously stored Transponder ID from memory.

NOTE: User Number and ID Number Values in the

following examples are for demonstration

purposes only; enter the appropriate values

for your system.

To Enter Program Mode:

Present Program cards to the unit in the sequence that represents the

password and then present the “ENTER” card. (All new units are pre-

programmed with the password 12345.) The LED will ﬂash amber to show

that the unit is in Program Mode. The unit will “time out” and return to Active

(Normal) Mode in 15 seconds if no Program card is presented.

1 + 2 + 3 + 4 + 5 +

Radio Key® 600e Operating & Installation

Secura Key  5

(User Number 12)

(ADD) (ENTER)

(ID Number 995)

(User Number 12)

(ADD) (ENTER)

(New Password - 54321)

(Re-type New Password - 54321) (ENTER)

Change your Password:

Put the unit into the Program mode, if necessary (see above). Present

the THRU Card to the unit. Then present the sequence of program cards

representing the desired new password (exactly 5 digits) to the unit. Then

present the THRU Card. Again present the sequence of program cards

representing the desired new password to the unit. Present the ENTER

card to the unit. A green light and beep means that the Password was

changed. Note that 12345 is the default (factory) password; use another

number sequence for best security.

* + 5 + 4 + 3 + 2 + 1 +

Add a Transponder (Key Tag) to the System:

Put the unit into the Program mode, if necessary (see above). Present

the ADD card to the unit and then present the sequence of program cards

representing the desired User Number (1-600) to the unit. Then present the

ENTER card to the unit. Hold the Transponder near the RK600e Unit. A green

light and beep means that the Transponder was accepted. A red light and three

beeps means a Transponder has already been stored for the selected User Number.

Delete the previously stored Transponder or select a new User Number.

+ 1 + 2 + (Hold Key Tag near unit)

Add a Transponder by Entering the Transponder ID:

Instead of presenting the transponder, you can also use the Program Deck

to enter the Transponder ID number: Put the unit into the Program mode, if

necessary (see above). Present the ADD card to the unit and then present

the sequence of program cards representing the desired User Number

(1 - 600) to the unit. Present the THRU Card. Present the sequence of

program cards representing the ID number printed on the Transponder.

Then present the ENTER card.

+ 1 + 2 + * + 9 + 9 + 5 +

Record the User Number and Transponder ID Number in the User Log Form.

Radio Key® 600e Operating & Installation

Secura Key  6

(VOID) (ENTER)

(Ending User Number 10) (ENTER)

(Starting User No. 1)

(VOID)

(User Number 12) (ENTER)

(VOID)

(Starting User No. 1) (Ending User Number 10)

(ADD) (ENTER)

Add a Series of Transponders to the System:

Put the unit into the Program mode, if necessary (see above). Present

the ADD card to the unit and then present the sequence of program cards

representing the desired starting User Number to the unit. Present the THRU

Card. Then present the sequence of program cards representing the desired

ending User Number. Present the THRU card, then present the ENTER

Card. Present the Transponders to the reader in the desired order (making a

careful record of which transponders are assigned to which User Numbers). If

one or more Transponders are already entered into the User Number range

you have selected, a red light and three beeps will occur, in which case, you

must delete the entire range (see below) before proceeding.

+ 1 + * + 1 + 0 + * +

Delete a Transponder from the System:

Put the unit into the Program mode, if necessary (see above). Present the VOID

card to the unit and then present the sequence of program cards representing

the desired User Number (1 - 600) to the unit. Then present the ENTER Card

to the unit. A green light and beep means that the Transponder was deleted.

+ 1 + 2 +

Delete a Range of Transponders from System:

Put the unit into the Program mode, if necessary (see above). Present the

VOID card to the unit and then present the sequence of program cards

representing the desired starting User Number to the unit. Present the

THRU Card. Then present the sequence of program cards representing

the desired ending User Number. Then present the ENTER Card. A green

light and beep means that the range of Transponders was deleted.

+ 1 + * + 1 + 0 +

Delete a Transponder by Presenting to Reader:

Put the unit into the Program mode, if necessary (see above). Present the

VOID card to the unit. Then present the ENTER Card to the unit. Hold the

Transponder near the RK600e Unit. A green light and beep means that the

Transponder was deleted.

+ (Hold Key Tag near Unit)

Table des matières

Autres manuels Securakey Système de contrôle

Securakey

Securakey RADIO KEY 600 Manuel utilisateur

Securakey

Securakey Radio Key RK-600 Guide de dépannage

Securakey

Securakey ENTRACOMP 26SA Mode d’emploi

Manuels Système de contrôle populaires d'autres marques

Pentair Pool Products

Pentair Pool Products Compool Manuel utilisateur

ComfortNET

ComfortNET CTK04 Manuel utilisateur

Fireye

Fireye InSight II 95DSS3 Manuel utilisateur

CAME

CAME G3000 Manuel utilisateur

Idemia

Idemia MorphoAccess VP MD Manuel utilisateur

Axis

Axis P1445-LE-3 Manuel utilisateur

HEIDENHAIN

HEIDENHAIN TNC 150 B Manuel utilisateur

CNC-Step

CNC-Step High-Z T-Series Manuel utilisateur

Doosan

Doosan DVF Series Manuel utilisateur

Honeywell

Honeywell KAP 140 Manuel utilisateur

Honeywell

Honeywell vk41 series Manuel utilisateur

AirBench

AirBench FPW Guide d'installation

Cypress

Cypress HHR-3160 Manuel utilisateur

CAME

CAME GLT40AOS Manuel utilisateur

Zonex

Zonex GEN II -VVT Guide de l'utilisateur

Altronics

Altronics K 9650 Manuel utilisateur

micro-trak

micro-trak RoadMaster Manuel utilisateur

micro-trak

micro-trak Calc-An-Acre II Manuel utilisateur