Securakey RADIO KEY 600 Manuel utilisateur

Radio Key® 600

STAND ALONE PROXIMITY ACCESS CONTROL SYSTEM

with PATENTED*

DYNASCAN® TECHNOLOGY

Operating & Installation Guide

Rev. J

www.SecuraKeyStore.com

(800) 878-7829

[email protected]

P/N 3320831

*Patent #6317027

SOUNDCRAFT, INC.

Radio Key® 600

Operating & Installation Guide

Table of Contents

Introduction ............................................................................................. 1

Programming Radio Key® 600 ................................................................ 3

Programming Hints .................................................................................. 7

Basic Operation ....................................................................................... 7

System Conﬁguration ............................................................................. 8

Wiring ...................................................................................................... 9

Power ......................................................................................................11

Installation .............................................................................................. 14

Troubleshooting ...................................................................................... 17

Returning a Unit ..................................................................................... 17

Ordering Additional Transponders .......................................................... 17

Warranty ................................................................................................. 17

Specifications ......................................................................................... 18

FCC Certification .................................................................................... 23

Illustrations

Figure 1, RK600 Components .................................................................. 2

Figure 2, MOV Wiring Diagram ............................................................... 10

Figure 3, Wiring Diagram ........................................................................ 12

Figure 4, Basic Installation ...................................................................... 15

Figure 5, Wall Mounting on Metal Surface with Optional Spacer ............ 16

Figure 6, Post/Flange Mounting .............................................................. 16

Tables

Table 1, Cable Types and Distances ........................................................ 9

Table 2, Connector P1 Color Coding ....................................................... 13

Table 3, Connector P2 Color Coding ...................................................... 13

V031008 7010

THIS PAGE INTENTIONALLY LEFT BLANK

Radio Key® 600 Operating & Installation

Secura Key  1

INTRODUCTION

The Radio Key® 600 is a programmable single-door access control system

which allows any mix of up to 600 Proximity Transponders (Key Tags) or

PIN codes for keypad entry. It can control an electric strike, magnetic lock,

or gate operator, and has an additional input for an exit switch and output

contacts for external alarm shunting. The major components are shown

in Figure 1.

The RK600 Access Control Unit contains the CPU, memory, access

relay, and an internal reader. It has a beeper, bi-color LED indicator and

a 16-position keypad, which is used to add or delete transponders or PIN

codes, to set the operating mode, to program the password and latch timer,

and for PIN entry. The RK600 is weather resistant and is provided with a

gasket for exterior installation.

Parts Supplied:

Access Control Unit

Gasket

MOV

Mounting Plate

Connector/Wire Pigtail

Operating Manual

Quick Start Guide and Wallet Sized Guide

User Log Form

2, 6-32 x 1/2” mounting screws

1, 4-40 x 5/16” Phillips housing screw

1, 4-40 x 5/16” Hex Socket, security housing screw

The RKAR Auxiliary Reader is optional, but recommended for extreme

weather or higher security applications. This reader parallels the internal

reader in the RK600. It contains a bi-color LED indicator and a beeper also

driven by the RK600. A gasket is provided for exterior installation.

The RKAT Audit Trail Module is optional and allows the RK600 to connect

to a PC or Printer for Audit Trail Reporting and programming. RK-LINKTM

Software for Windows® is included.

RK-PS, a 12VDC plug-in power supply is optional. It is designed to power

the RK600 only, and requires 120 VAC input. RK600-BB Back Box / Spacer

is optional. It extends the RK600 out from the mounting surface and provides

additional room for wiring.

Radio Key® 600 Operating & Installation

Secura Key  2

RKAR

RK600 Unit Auxiliary Reader

(optional)

Mounting Plate RK600-BB

Back Box/ Spacer

(optional)

Figure 1 - RK600 Components

Radio Key® 600 Operating & Installation

Secura Key  3

PROGRAMMING RADIO KEY® 600

Radio Key® Transponders (Key Tags) are pre-encoded and engraved at the

factory with unique Transponder ID numbers. Because these numbers are

unique, Facility Codes (Site Codes) are not required.

Transponder ID Numbers are not pre-programmed into the Radio Key® 600;

you must add them to the system as described below.

Radio Key® 600 allows you to assign either a Transponder or a PIN code

to each User Number (1 - 600) for programming purposes. The User

Number is associated with the individual person using the transponder or

PIN code.

Be sure to record the User Number, the Transponder ID Number or

PIN code and the user’s name, and keep this information in a secure

place. A blank User Log Form has been included for this purpose. Do not

write on this form; use it as a photocopy master.

Because a new Transponder ID Number or PIN can be assigned to any

available User Number, the reader always has capacity to store 600

Transponders or PINs, even after many Transponders or PINs have been

voided from the reader.

Error Warnings

A red light and three beeps at the end of a keypad sequence means that

you have made an error. Refer to the appropriate section, and carefully

re-enter the command in the proper sequence.

If you select a User Number for a new Transponder or PIN, and a Transponder

ID Number or PIN has already been stored in memory for that User Number,

a red light and three beeps will occur. Select another User Number or void

the User Number, which removes the previously stored Transponder ID or

PIN Number from memory.

NOTE: User Number and ID Number Values in the

following examples are for demonstration

purposes only; enter the appropriate values

for your system.

Radio Key® 600 Operating & Installation

Secura Key  4

(Password) (ENTER)

(User Number 12)

(ADD) (ENTER)

(User Number 12)

(ADD) (ENTER)

(ID Number 995)

(Starting User No. 1) (Ending User Number 10)

(ADD) (ENTER)

PROGRAMMING STEPS

To Enter Program Mode:

Enter your 5-digit password, then press ENTER. (All new units are pre-

programmed with the password 12345.) The LED will ﬂash amber to show

that the unit is in Program Mode. The unit will “time out” and return to Active

(Normal) Mode in 15 seconds if no key is pressed.

1 + 2 + 3 + 4 + 5 +

Add a Transponder (Key Tag) to the System:

Enter Password. Press ENTER. Press ADD. Enter a User Number (1 - 600) and

press ENTER. Hold the Transponder near the RK600 Unit. A green light and

beep means that the Transponder was accepted. A red light and three beeps

means a Transponder has already been stored for the selected User Number.

Delete the previously stored Transponder or select a new User Number.

+ 1 + 2 + (Hold Key Tag near unit)

Add a Transponder by Entering the Transponder ID:

Instead of presenting the transponder, you can also use the Keypad to enter the

Transponder ID number: Enter Password. Press ENTER. Press ADD, enter the User

Number, press

*, enter the ID number printed on the Transponder, then press ENTER.

+ 1 + 2 + * + 9 + 9 + 5 +

Record the User Number and Transponder ID Number in the User Log Form.

Add a Series of Transponders to the System:

Enter Password. Press ENTER. Press ADD. Enter the Starting User

Number in the range. Press

, enter the Ending User Number, press

, then

press ENTER. Present the Transponders to the reader in the desired order

(making a careful record of which transponders are assigned to which User

Numbers). If one or more Transponders are already entered into the User

Number range you have selected, a red light and three beeps will occur, in

which case, you must delete the entire range before proceeding.

+ 1 + * + 1 + 0 + * +

Radio Key® 600 Operating & Installation

Secura Key  5

(User Number 14)

(ADD) (PIN Code 3253) (ENTER)

(ID Number 995)

(VOID) (ENTER)

(Ending User Number 10) (ENTER)

(Starting User No. 1)

(VOID)

(User Number 12) (ENTER)

(VOID)

Add a PIN to the System:

Enter Password. Press ENTER. Press ADD. Enter the User Number

and press ADD, enter the 4-digit PIN code, then press ENTER.

+ 1 + 4 + + 3 + 2 + 5 + 3 +

Note: A PIN must be 4 digits. If the PIN has leading zeros, they must be

entered as this example shows - “0004”.

Delete a Transponder or PIN from the System:

Enter Password. Press ENTER. Press VOID. Enter the User Number. Press

ENTER. A green light and beep means that the Transponder or PIN was deleted.

+ 1 + 2 +

Delete a Range of Transponders/PINs from System:

Enter Password. Press ENTER. Press VOID. Enter the Starting User

Number in the range, press

, enter the Ending User Number, then press

ENTER. A green light and beep means that the range of Transponders/

PINs was deleted.

+ 1 + * + 1 + 0 +

Delete a Transponder by Presenting to Reader:

Enter Password. Press ENTER. Press VOID, then press ENTER. Hold the

Transponder near the RK600 Unit. A green light and beep means that the

Transponder was deleted.

+ (Hold Key Tag near Unit)

Delete a Transponder by Entering Transponder ID:

Enter Password. Press ENTER. Press VOID, press

, enter the ID number

printed on the Transponder, then press ENTER. A green light and beep

means that the transponder was deleted.

+ * + 9 + 9 + 5 +

Radio Key® 600 Operating & Installation

Secura Key  6

(New Password - 54321)

(Re-type New Password - 54321) (ENTER)

(5 Seconds)

(SET TIMER) (ENTER)

(Mode Number 2)

(MODE) (ENTER)

Change your Password:

Enter your current Password. Press ENTER. Press

, then enter the new

Password (exactly 5 digits). Press

again, then re-enter the new Password

and press ENTER. A green light and beep means that the Password was

changed. Note that 12345 is the default (factory) password; use another

number sequence for best security.

* + 5 + 4 + 3 + 2 + 1 +

+ 5 + 4 + 3 + 2 + 1 +

Set the Latch Timer:

Enter Password. Press ENTER. Press SET TIMER. Enter the number of

seconds (0-30). Press ENTER. A green light and beep means that the

Latch Timer setting was changed.

+ 5 +

Set the Operating Mode:

Enter Password. Press ENTER. Press MODE, then press 1, 2 or 3 and

Press ENTER. The Access Control Unit will exit Programming Mode and

enter the selected Mode. Selections are:

1. Active (Normal) -- LED is Off

2. Inactive (Locked) -- LED blinks Red

3. Door Unlocked -- LED blinks Green

+ 2 +

To Exit Programming Mode Immediately:

Press MODE, then press 1, then press ENTER. This returns the unit to

normal mode immediately, bypassing the 15 second time-out.

+ 1 +

Autres manuels pour RADIO KEY 600

Table des matières

Autres manuels Securakey Système de contrôle

Securakey

Securakey ENTRACOMP 26SA Mode d’emploi

Securakey

Securakey Radio Key 600e Manuel utilisateur

Securakey

Securakey Radio Key RK-600 Guide de dépannage

Manuels Système de contrôle populaires d'autres marques

Pentair Pool Products

Pentair Pool Products Compool Manuel utilisateur

ComfortNET

ComfortNET CTK04 Manuel utilisateur

Fireye

Fireye InSight II 95DSS3 Manuel utilisateur

CAME

CAME G3000 Manuel utilisateur

Idemia

Idemia MorphoAccess VP MD Manuel utilisateur

Axis

Axis P1445-LE-3 Manuel utilisateur

HEIDENHAIN

HEIDENHAIN TNC 150 B Manuel utilisateur

CNC-Step

CNC-Step High-Z T-Series Manuel utilisateur

Doosan

Doosan DVF Series Manuel utilisateur

Honeywell

Honeywell KAP 140 Manuel utilisateur

Honeywell

Honeywell vk41 series Manuel utilisateur

AirBench

AirBench FPW Guide d'installation

Cypress

Cypress HHR-3160 Manuel utilisateur

CAME

CAME GLT40AOS Manuel utilisateur

Zonex

Zonex GEN II -VVT Guide de l'utilisateur

Altronics

Altronics K 9650 Manuel utilisateur

micro-trak

micro-trak RoadMaster Manuel utilisateur

micro-trak

micro-trak Calc-An-Acre II Manuel utilisateur