Sebury sReader-w Manuel utilisateur
sReader-w / sReader-s
User Manual
Please read this instruction completely and keep it properly
Product Introduction
sReader adopts high-strength ABS plastic appearance.EM,HID and IC card reading
are supported.Bluetooth analog card Wiegand output function of mobile phone,
built-in high integration micro-controller and simple circuit are applied. safety and
reliability are assured. sReader is cost effective and durable, suitable for office,
communiy and other context using.
Performance Parameters
Body Material:
Bluetooth Function:
Card Type:
Reading range:
Output format:
Input voltage:
Quiescent current:
Operating temperature:
Operating humidity:
ABS Plastic
Mobile phone Bluetooth analog output card number，shared by
one administrator to multiple users
EM, HID card (125kHz)
IC card (including Mifare and CPU card, 13.56MHz, ISO14443a)
≤ 5cm
Wiegand 26-37bit (Default 26bit, Customized for other formats)
DC12 ± 2V
≤ 50mA
- 20 ～ 50 ℃
0-95%
sReader-w Dimension: 120 * 85 * 23mm
sReader-s Dimension: 107 * 48 * 23mm
Ingress protection: IP65 (water and dust-resistant)
Wires and Instruction
1 Red +12V
2 Black GND
3 Green D0
4 White D1
5 Brown LED
6 Yellow BZ
Serial No. Color Definition Instruction
Positive pole
Negative pole
Wiegand output
Wiegand output
Green LED control input
Buzzer control input
Packing List
Card Reader*1
Self Tapping Screw KA4*25mm ( sReader-w*4 ）
Punch Sticker*1
User Manual*1
Screw Hole Decoration Piece*1
Expansion Rubber Bung Φ6*24mm ( sReader-w*4）
sReader-w / sReader-s
User Manual
Please read this instruction completely and keep it properly
Installation
Stick the punch sticker on the wall. Drill 2 Φ6mm intallation holes with purcussion drill
with the depth of 26mm.（4 holes for sReader-w ）
Drill Installation Holes
Drill Φ10mm hole for outlet with the depth according to the practical situation of
electric lines.
Drill the Hole for Outlet
Click 2 expansion rubber bungs into the installation holes （4 expansion rubber
bungs for sReader-w）
Click Expansion Rubber Bung
Fix the back shell on the wall with 2 K4*25 self tapping screws（4 screws for sReader-w）
（The percussion drill,hammer and screwdriver in figure2,3 and 4 should be self prepared.）
Fix the Back Shell
Put the outlet cables through the Φ10mm hole and connect the needed cables.(Pack
the useless cables with the insulating tape.)
Connect Cables
Put the front shell on the back shell. Install the tamper screw from the bottom of the
device with screwdriver and stick the screw hole decoration piece onto the device.
Install the Front Shell and Screw Hole Decoration Piece
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Sebury Contrôleurs d'accès IP
Sebury
Sebury K3-3 Manuel utilisateur
Sebury
Sebury sPress2 Manuel utilisateur
Sebury
Sebury sKey2 Manuel utilisateur
Sebury
Sebury K3-3 Manuel utilisateur
Sebury
Sebury F2 Manuel utilisateur
Sebury
Sebury BC-2000 Manuel utilisateur
Sebury
Sebury F007EM-II Manuel utilisateur
Sebury
Sebury Q3 Manuel utilisateur
Sebury
Sebury sTouch2 Manuel utilisateur
Sebury
Sebury BC2019 Manuel utilisateur
