Sealey AP2020 Manuel utilisateur

INSTRUCTIONS FOR:

HEAVY-DUTY WORKBENCH WITH 2 DRAWERS

MODEL:AP2020

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and

properly maintained, give you years of trouble free performance.

1. SAFETY INSTRUCTIONS

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.

USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE

DAMAGE OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

2. CONTENTS

1.1 GENERAL SAFETY

pWARNING! Ensure Health & Safety, local authority, and general workshop practice

regulations are adhered to when using this bench.

3Locate bench in a suitable working area.

3Keep the work area clean, uncluttered and ensure there is adequate lighting.

pWARNING! Use bench on level and solid ground, preferably concrete. Avoid tarmacadam

since the bench may sink into the surface.

3Keep the bench clean and tidy in accordance with good workshop practice.

3Keep children and unauthorised persons away from the working area.

7DO NOT use the bench for any purpose other than that for which it is designed.

7DO NOT undertake work on the bench without the workpiece being adequately secured. Use

clamps or a vice (not included) to secure the workpiece. Available from your Sealey dealer.

7DO NOT use the bench out of doors.

7DO NOT get the bench wet or use in damp or wet locations or areas where there is

condensation.

7DO NOT clean the bench with any solvents which may damage the paint surface or the

protective coating on the wooden top.

pMaximum weight for each drawer is 25 kg, full load for Workbench is 250 kg

AP2020 - 1 - 061005

2.1 Carefully unpack the product and check the contents against the diagram below. Should any items be missing or damaged make

immediate contact with your Sealey dealer.

01284 757500

01284 703534 sales@sealey.co.uk

Sole UK Distributor

Sealey Group,

Bury St. Edmunds, Suffolk.

www.sealey.co.uk

Web

3. ASSEMBLY

STEP 1. Take two crossrails (B) and bolt them

to the cabinet sides (A) using 8 bolts (O), 8 lock

washers (P), and 8 nuts (Q). Ensure that the

pairs of holes that accept the corner braces are

facing downwards. (Refer to STEP 7.)

STEP 2. Bolt the two centre supports (C) to the

front and back crossrails respectively using 4

bolts (O), 4 lock washers (P), and 4 nuts (Q).

STEP 3. Bolt 2 left & 2 right slide panels (D) &

(E) into position, only bolt at front of Work

Bench using 8 bolts (O), 8 lock washers (P),

and 8 nuts (Q). Fix 1 left hand female slide (L),

at top onto each slide panel (D) and 1 right

hand female slide (L), onto each slide panel (E)

Refer to Diagram 11 on how to fit slides.

STEP 4. Take two crossrails (B) and bolt them

to the cabinet sides (A) and centre supports (C)

using 12 bolts (O), 12 lock washers (P), and 12

nuts (Q).

STEP 5. T

ake two draw stops (G) and one back

panel (F) and bolt them to the back of the

cabinet with the draw stops between the panel

and the cabinet. Repeat procedure with the

other back panel and 2 draw stops. Use 8 bolts

(O), 8 lock washers (P), and 8 nuts (Q).

STEP 6. Turn the cabinet upside down and bolt

the two shelf components (H) into position at

the bottom of the unit using 8 bolts (O), 8 lock

washers(P), and 8 nuts (Q).

AP2020 - 1 - 061005

STEP 7. Screw in the four adjustable leg

levellers (R). Bolt the four corner braces (I) into

position using 16 bolts (O), 16 lock washers

(P), and 16 nuts (Q)

STEP 8. Place the wooden top (N) face down

on a flat, clean, smooth surface. Position the

cabinet upside down on the wooden top and

mark the hole locations on the top. Move the

cabinet to one side and drill 5/32 diameter x

1/2 deep holes in the top. DO NOT DRILL

DEEPER THAN 1/2. Attach frame to top with

the 4 hex head screws (S).

STEP 10. Attach a left hand female slide (K) to

left hand side of each draw and a right hand

female slide (K) to the right hand side of each

draw (see diagram 11). Engage each draw onto

the protruding male slides and push fully home,

then open the draw to check that it is retained.

Diagram 11. Orientate each slide as shown in the diagram above with the rear hook pointing

towards the rear of the draw or the rear of the cabinet. Put the rear hook on each slide into the

square hole nearest the back of the draw or the back of the cabinet and push the slide backwards

to engage the hook. Swivel the front of the slide up or down slightly until the other two hooks appear

in the other two holes. Keep the rear face of the slide up against the draw or slide panel. On the

draws pull the slide sharply upwards to engage it. On the cabinet push the slides down to engage.

STEP 9. Take the 4 male slide components (M)

and slide 2 onto the female slides on the left of

the draw compartment and 2 onto the female

slides on the right hand side of the draw

compartment. Push them fully in to engage

them, then pull them out to the stop point.

AP2020 - 1 - 061005

10 11

Autres manuels Sealey Rangement des outils

Sealey

Sealey AP1210 Manuel utilisateur

Sealey

Sealey AP2010.V2 Manuel utilisateur

Sealey

Sealey AP2020BB Manuel utilisateur

Sealey

Sealey PTB181510 Manuel utilisateur

Sealey

Sealey AP2030 Manuel utilisateur

Sealey

Sealey CX313.V2 Manuel utilisateur

Sealey

Sealey AP335M Manuel utilisateur

Sealey

Sealey AP930M Manuel utilisateur

Sealey

Sealey APMS01 Manuel utilisateur

Sealey

Sealey AP2050 Manuel utilisateur

Sealey

Sealey AP1200M Manuel utilisateur

Sealey

Sealey AP22DFC Manuel utilisateur

Sealey

Sealey APMSV Series Manuel utilisateur

Sealey

Sealey AP2200BB.V2 Manuel utilisateur

Sealey

Sealey AP12160 Manuel utilisateur

Sealey

Sealey AP3508TB Manuel utilisateur

Sealey

Sealey AP3020 Manuel utilisateur

Sealey

Sealey AP41104BWS Manuel utilisateur

Sealey

Sealey AP4707S Manuel utilisateur

Sealey

Sealey AP2513B.V4 Manuel utilisateur

Sealey

Sealey FWB1.V3 Manuel utilisateur

Sealey

Sealey AP2200BB.V2 Manuel utilisateur

Sealey

Sealey PTB141007 Manuel utilisateur

Sealey

Sealey AP28104 Manuel utilisateur

Manuels Rangement des outils populaires d'autres marques

Ryobi

Ryobi RWB03 Manuel utilisateur

Husky

Husky H27CH5TR4BGK Manuel utilisateur

Scheppach

Scheppach ts 2100 Manuel utilisateur

Cornwell Tools

Cornwell Tools CTB360AKBK Manuel utilisateur

DIVERSIFIED WOODCRAFTS

DIVERSIFIED WOODCRAFTS SHAIN GSB-6024 Manuel utilisateur

Cassese

Cassese CS200 CART Manuel utilisateur

Kendall Howard

Kendall Howard ESDW-9630-1000 Manuel utilisateur

Lista

Lista Align Instructions de montage

Workzone

Workzone 99609 Manuel utilisateur

Stanley

Stanley STST83800-1 Manuel utilisateur

Homak

Homak PROFESSIONAL Series Manuel du système

Perel

Perel ROLLER SHUTTER STORAGE CABINET Manuel utilisateur

Husky

Husky H5CH2R Manuel utilisateur

BGS technic

BGS technic 4107 Manuel utilisateur

Clarke

Clarke CWB1250 Manuel utilisateur

Ryobi

Ryobi RWB02 Manuel utilisateur

Husky

Husky H52CH6HDV3WHT Manuel utilisateur

General International

General International Excalibur 40-100 Manuel de la liste des pièces