Sealey AK9621EV Manuel utilisateur
INSTRUCTIONS FOR:
MODEL:
AK9621EV
AK9621EV
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS, AND
CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE, FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO
MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.
!WARNING! Ensure Health and Safety, local authority and general workshop practice regulations are adhered to
when using tools and equipment.
"DO NOT use AK9621EV if damaged.
#Maintain AK9621EV in good and clean condition for best performance.
#Keep the work area clean, uncluttered and ensure there is adequate lighting.
#Keep children and unauthorised persons away from the work area.
"DO NOT use the AK9621EV for any purpose other than for which it is designed.
"DO NOT get AK9621EV wet or use in damp or wet locations, or areas where there is condensation. Keep AK9621EV clean
and dry using a dry cotton cloth only.
"DO NOT dip or submerge the AK9621EV in any type of liquid.
"DO NOT expose AK9621EV to bright sunlight or dust.
"DO NOT dis-assemble AK9621EV. The AK9621EV must be checked by qualified service personnel only.
"DO NOT apply any voltage to the AK9621EV i.e. with an electric marker pen.
#The AK9621EV is a precision instrument, treat with care, avoid using force and do not subject to knocks or shocks.
#Use AK9621EV in reasonably constant temperature conditions of approximately 20OC.
#When not in use, turn off and store gauge in a safe, dry, childproof location.
1. SAFETY INSTRUCTIONS
2. INTRODUCTION & SPECIFICATION
AK9621EV - 1 - 290307
Hardened and tempered stainless steel digital calliper with satin finish. Large LCD display with 11mm high figures for ease of
reading. Metric and Imperial calibration with conversion between the two. Zero setting control allows comparative measurement.
Supplied in robust storage case.
DIGIT
DIGITAL
AL VERNIER CALLIPER 0-150
VERNIER CALLIPER 0-150mm
mm/0-6”
/0-6”
1 Internal Measure 5 LCD Display 9 Battery Cover
2 On\mm\inch Button 6 External Measure 10 Depth Measure
3 Locking Screw 7 Off Button 11 Step Measure
4 Fine Adjust Wheel 8 Zero Button
Specification
Resolution 0.01mm (0.0005”)
Range 0-150mm (0-6”)
Accuracy ±0.03mm/0.001”
Functions Zero set, mm/inch select, incremental zero.
Messages Flashing display = replace battery
Battery life Approx. two years (approx. one year in continuous service)
Battery SR44 - 1.5V
Operational Temperature range 0 - 40OC
Fig 1
Sole UK Distributor,
Sealey Group,
Bury St. Edmunds, Suffolk.
01284 757500 E-mail: sales@sealey.co.uk
01284 703534
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
www.sealey.co.uk
Web
3. OPERATION
4. MAINTENANCE
3.1. Ensure all measuring surfaces are clean and then turn on calliper by pressing
‘ON’ button. Wait at least one second before use.
3.2. Loosen locking screw and close calliper; if read-out does not show zero when
in closed position, reset by pressing ‘Zero’ button.
3.3. Select inch or mm units, as required, with the metric/imperial selector. Check
that display shows the required units.
3.4. Measurements will now be shown directly on the LCD display.
3.5. A new zero may be obtained, at any open position of the calliper, by pressing
the zero control.
3.6. When finished, turn off and store calliper in a safe, dry, childproof location.
4.1 BATTERY INSTALLATION/REPLACEMENT
NOTE! The battery should last for one year of continuous use. If the display is blank
or the digits are flashing the battery voltage is too low, replace the battery with a new
SR44 power cell. If the digits do not change when buttons are pressed or probe is
moved, remove the battery for 1 minute to reset the unit. The battery should be
removed if the gauge is not to be used for a long period of time.
4.1.1. Lift off the battery cover (fig 2) after removing the two screws.
4.1.2. Remove exhausted battery and fit replacement with +ve side uppermost and
fix the cover back into place using the two screws.
4.1.3. Dispose of old battery in a safe and approved manner. Do not burn.
If the display fails to alter when the slide is moved, remove the battery, wait
at least 1minute and then refit the battery.
Environmental Protection.
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be
sorted, taken to a recycle centre and disposed of in a manner which is compatible with the environment.
When the product is no longer required, it must be disposed of in an environmentally protective way.
Do not incinerate battery as it may explode when exposed to fire.
Do not attempt to open battery.
Contact your local solid waste authority for recycling information.
Fig 2
Table des matières
Autres manuels Sealey Instrument de mesure
Sealey
Sealey AK4013 Manuel utilisateur
Sealey
Sealey BT91/5.V3 Manuel utilisateur
Sealey
Sealey VSE3157 Manuel utilisateur
Sealey
Sealey TA500 Manuel utilisateur
Sealey
Sealey VS0560.V2 Manuel utilisateur
Sealey
Sealey STW701 Manuel utilisateur
Sealey
Sealey TA200.V2 Manuel utilisateur
Sealey
Sealey MM405 Manuel utilisateur
Sealey
Sealey PP5 Manuel utilisateur
Sealey
Sealey Auto Service Line VS0565 Manuel utilisateur
Sealey
Sealey Auto Service VS8196.V2 Manuel utilisateur
Sealey
Sealey GA70CR Manuel utilisateur
Sealey
Sealey VS0561 Manuel utilisateur
Sealey
Sealey PP7 Manuel utilisateur
Sealey
Sealey Professional AUTO SERVICE TA100 Manuel utilisateur
Sealey
Sealey AK4013 Manuel utilisateur
Sealey
Sealey TA203.V2 Manuel utilisateur
Sealey
Sealey TA320 Manuel utilisateur
Sealey
Sealey VSE110 Manuel utilisateur
Sealey
Sealey MM404.261 Manuel utilisateur
Manuels Instrument de mesure populaires d'autres marques
Endress+Hauser
Endress+Hauser Proline Promag 50 Caractéristiques techniques
Siemens
Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces
KLINGER
KLINGER CMF V Series Manuel utilisateur
EXFO
EXFO FTB-2 Manuel d'exploitation et d'entretien
Keysight
Keysight M8290A Manuel utilisateur
ADTEK
ADTEK MW-5 Manuel utilisateur