Seagate MEDALIST 275XE Manuel utilisateur

. . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . .

Medalist XE Family

. . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . .

275xe, 545xe

. . . . . . . . . . . . . . . . . . . . . . . . .. . . .

ATA Interface Drives

. . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . .

Installation Guide

. . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . .

Publication Number: 36294-001, Rev. A

December 1994

Seagate, Seagate Technology and the Seagate logo are registered

trademarks of Seagate Technology, Inc. Medalist, SeaFAX, SeaFONE,

SeaBOARD and SeaTDD are trademarks of Seagate Technology, Inc.

EZ-Drive and Maximum Overdrive are trademarks of Micro House

International, Inc. Other product names are registered trademarks or

trademarks of their owners.

Seagate reserves the right to change, without notice, product offerings

or specifications. No part of this publication may be reproduced in any

form without written permission from Seagate Technology, Inc.

Contents

Read before you begin...

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

ST3660A free installation software. . . . . . . . . . . . . . . . . . . . 2

Quick software transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Installing the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Configuring the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Attaching cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Mounting the drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Configuring the computer . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

528-Mbyte system-capacity limit . . . . . . . . . . . . . . . . . . . . . 7

Standard installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Partitioning and formatting the drive . . . . . . . . . . . . . . . . . . 9

Transferring and using the installation software . . . . . . . 11

Transferring the installation software. . . . . . . . . . . . . . . . . 11

Using the installation software. . . . . . . . . . . . . . . . . . . . . . 12

Basic troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Advanced troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . 19

Technical support services. . . . . . . . . . . . . . . . . . . . . . . . . 25

Storing and shipping your drive. . . . . . . . . . . . . . . . . . . . . 28

Read before you begin...

Application. Your Seagate® drive is designed for NRTL-listed

personal computers. It uses the ATA interface.

Warning. Turn off thecomputer before you openthecase, touch

any internal components or install the drive.

Static discharge. Yourdrive and computer contain components

that can be damaged by static discharge. Static electricity is

generated from the friction of two contributors rubbing together.

The charge is stored in your body and is discharged when you

touch another conductor. Wool, synthetic clothing, carpets and

plastics,including mostbags,arecommoncontributors.Observe

these precautions to avoid damage from static electricity:

•Ground yourself before handling the drive. Wear a grounded

wriststrap thatisproperlyconnectedtoearthground,ortouch

themetal chassis ofthe computer powersupplyifitis plugged

into a grounded outlet.

•Keep the drivein its antistatic bag until you are ready to install

it. Do not attach any cables to the drive in the antistatic bag.

•Handle the drive gently and only by its edges or frame.

•Donottouchthedrive’sconnectorpinsorprintedcircuitboard.

Drive handling. The drive is extremely fragile—handle it with

care. Do not remove any labels from the drive.

Inspection. Hold the drive by the frame edges to inspect it. Call

your distributorordealerimmediatelyifitappearstobedamaged.

Warranty. See your authorizedSeagate distributor or dealer for

the terms of the drive warranty.

Note. With regard to the EZ-Drive software,thereare no warran-

ties, express or implied, including, but not implied,warran-

ties ofmerchantablityorfitnessforaparticularpurpose.All

such warrantiesareexpresslyand specificallydisclaimed.

Medalist XE Family Installation Guide, Rev. A 1

Maintenance and repair. Seagate drives do not require mainte

nance. The head/disc assembly is factory-sealed; a broken seal

voids the warranty. Seagate customer service centers are the

only facilitiesauthorizedto repair Seagate drives. Seagate does

not sanction any third-party repair facilities.

Note. Throughout this manual, the Medalist 275xe is referred to

by its model number, ST3295A,and theMedalist 545xeis

referred to by its model number, ST3660A.

ST3660A free installation software

Files containing the free hard disc installation software and a

program for extracting them, Seamove, are written on the

ST3660A drive at the factory. The installation software is a

versionof EZ-DriveforSeagate. Itprovides asoftware solution

forcomputersusingDOSandsomeBIOS combinations thatlimit

the hard disc capacity to 528 Mbytes. It allows the computer to

access the ST3660A’s entire 544.8 Mbytes. Before you partition

and format the drive, transfer the EZ-Drive files to a bootable

diskette. Instructions for transferring the EZ-Drive files are on

page 11 and in the README.EXEfile on the drive.

Note. The EZ-Drive software is authorized for installation only

with the drive on which it is shipped.

Quick software transfer

•Install the ST3660A drive.

•Boot the computer with a diskette that has 300 Kbytes avail-

able for transferring the files.

•Select drive type 2 for the ST3660A in CMOS.

•Activate the prompt for the ST3660A.

•Type seamove. Seamove transfers the files to the diskette in

Drive A, erases the drive partition and reboots the computer.

2 Medalist XE Family Installation Guide, Rev. A

Front

4-pin

power connector

8-pin

master/slave jumper block

Front

Cable select

40-pin

ATA interface

connector

Circuit board

+5V

+5V return

+12V return

+12V

The drive is a master; a 

slave is present that uses

only the PDIAG– signal.

2-pin

header

Drive activity

LED 

(optional)

3-pin

power connector 

(optional)

123

Keyway

Ground

+12V

+5V

The drive is a master;

a slave is present, but

it is not ATA-compatible.

The drive is a slave to an

ATA-compatible master.

The drive is a master;

the slave is either a

Medalist family drive or 

another ATA-compatible 

drive, or there is no slave.

Circuit

board

Pin 1

Spare jumper 

across pin 1 and pin 3

–

Figure 1. Jumpers and connectors

Medalist XE Family Installation Guide, Rev. A 3

Installing the drive

1. Turn the computer off.

Warning. Installing or removing the drive or adapter cards

while the computer is powered on can damage

your drive, adapter and computer.

2. Remove the computer’s cover.

Caution. Special trainingor tools mayberequired toservice

laptop computers. Removing the cover may void

your warranty. Review the terms and conditions of

your warranty before removing the cover.

3. Ground yourself.

Configuring the drive

YourST3295Aor ST3660A is configured at the factoryforsingle-

drive operation. If you are installing two drives, you must recon-

figure your Seagate drive as either the master orthe slave. If you

installtheSeagatedriveasyouronlydrivebutaddaseconddrive

later, you must reconfigure it as the master or slave at that time.

1. Remove the drive from its antistatic bag.

2. Install master/slave jumpers. The master/slave configura-

tion is set using the jumper block shown in Figure 1 on page

3. The chart below the jumper block shows how to set the

jumpers for different configurations. An extra jumper is in-

cluded with the drive and is attached to pins 1 and 3 of the

jumper block.

Installing one drive: No jumper setup is required.

Installing two drives: Your Seagate drive may be installed

with another ATA-compatible drive. Your system may use

either a standard ATA interface cable or the cable-select

method. The chart in Figure 1 shows the jumper settings for

the master and slave configurations.

4 Medalist XE Family Installation Guide, Rev. A

Attaching cables

Refer to Figure 1 on page 3 for the locations of the connectors.

1. Connect the remote LED (optional).

2. Attach the power cable. Attach one of the cables from the

power supply to the power connector on the drive.

Caution. The cable and connector are designed to mate. Donot

force a connection. Improper alignment may damage

your drive.

3. Attach the interface cable. The edge-stripe on the interface

cable for the drive is used to denote pin 1. The cable length

must be no longer than 18 inches.

Caution. Cable misalignment can result in damage to the com-

puter and the drive. Ribbon cables are delicate—be

careful not to crimp or strain them.

Installing one drive with a standard ATA 40-pin interface cable:

Attach oneendofthe cabletothedrive’s40-pinATAinterface

connector. Alignthecable’s edge-stripewith pin 1 of thedrive

shown inFigure1.Attachtheotherendofthecabletothehost

adapter card or to the hard drive connector located on the

motherboard.Alignthecable’sedge-stripewithpin1(seeyour

system user’s guide or host adapter user’s guide).

Installing two drives with an ATA interface cable:

You needan interface cable designedfor two drives. Attach a

cable connector to each drive’s 40-pin ATAinterface connec-

tor. Align thecable’s edge-stripe with pin 1 of the drive shown

in Figure 1. Attach the other end of the cable to the host

adapter card or to the hard drive connector located on the

motherboard.Alignthecable’sedge-stripewithpin1(seeyour

system user’s guide or host adapter user’s guide). You can

attach the drives in any order on the cable.

Medalist XE Family Installation Guide, Rev. A 5

Installing drives in computers that use cable-select:

If your computer uses the cable-select method, refer to your

computerreferenceguidetodeterminewhichcableconnector

or drive slot denotes the master drive and which the slave.

Mounting the drive

YourSeagate drive isdesignedto fitinto a3.5-inchbay.You can

mount the drivesecurely in thecomputer in any orientation using

either the side mounting holes or the bottom mounting holes.

Position the drive so that you do not strain or crimp the cables.

YourSeagate driveisnotshippedwithmountingscrews.Usethe

screws in the current drive if this drive is a replacement.

•Drives that have an “S” stamped on the frame runner use

6-32 UNC standard screws.

•Drives that have an “M” stampedon the framerunner use M3

metric screws.

Caution. To prevent drive mounting hole damage, use only the

appropriate type of screws as specified. Tighten them

gently using no more than 6 inch-lb of torque.

Bottom mounting holes. Insert four mounting screws not more

than 0.20 inches (6 full turns) into the drive frame.

Sidemountingholes.Insertfourmountingscrewsnotmorethan

0.13 inches (4 full turns) into the drive frame.

5.25-inch drive bay. You can mount your drive in a 5.25-inch

drivebay with a Seagate 5.25-inch frame kit.Contact your dealer

for the frame kit you need.

6 Medalist XE Family Installation Guide, Rev. A

Configuring the computer

Your computer maintains records representing the hardware in

thesystem.Thisrepresentationincludesthetranslationgeometry

that is used by the BIOS to map the drive surface and that is

stored in CMOS memory. During the boot cycle, a test is run

comparing the record to the hardware. When you install a new

drive, you must update this record to includea representation of

the new drive. This is done in your computer’s System Setup.

This section tells you how to configure your computer. It also

discusses drivecapacitylimitationsimposedby some computers

and available solutions. If youare installing aST3295A,go tothe

“Standard installation” section on page 8.

528-Mbyte system-capacity limit

Computers using DOS and some BIOS impose a 528-Mbyte

capacity limit on ATA hard discs. This occurs because the BIOS

isdesigned touseup to1,024 cylindersinthe translationgeome-

try for mapping the data surface of the drive. The ST3660A has

1,057cylinders. If your computer’s BIOS limits the drivecapacity

to 528 Mbytes, you have several options for installingthe drive.

•Install the drive using the standard installation procedure on

page 8. This assures you the maximum capacity allowed by

your computer.

•Use a host adapter that supports more than 528 Mbytes.

•Upgrade the BIOS to one that uses logical block addressing

(LBA) or an extended cylinder-head-sector (ECHS) address-

ing scheme that allows for more than 528 Mbytes.

•Use the hard disc installation software, EZ-Drive,included on

your ST3660A drive. Instructions for extracting the software

are on page 11. Instructions for using EZ-Drive start on page

(Only ST3660A drives with part number 958002-4

are

shipped with EZ-Drive.)

Medalist XE Family Installation Guide, Rev. A 7

Standard installation

1. Turn the computer on.

2. Enter the System Setup routine. (Refer to your computer

user’s guide.SystemSetup maybecalledSetup,BIOSSetup

or CMOS Setup.) If your computer uses an automatic setup

utility, see the caution below.

3. Find the hard disc configuration in the System Setup screen.

4. Selectadrivetypethatmatchesthedrivetranslationgeometry

for your drive as shown in the followingtable.

Model CHKDSK

Mbytes

Translation geometry CMOS

(Setup)

Mbytes

Cyl Heads Sectors

per track

ST3295A 272.7 761 14 50 260

ST3660A* 545.5 1057 16 63 520

ST3660A** 528.5 1024 16 63 504

*Use this translation geometry if you know your computer

can accept more than 1,024 cylinders.

** Use this translation geometry if you are not sure your

computer can accept more than 1,024 cylinders.

Note. CHKDSK and CMOS capacities are approximations.

Thecapacitiesyourcomputerreportsmayvaryslightly.

Caution. If your computer is capable of automatic System

Setup, it may read the total number of physical

cylinders into the translation geometry chart in

System Setup. If your system does not acknow-

ledge more than 1,024 cylinders, it may overwrap

the initial cylinders in its representation. This re-

duces the effective drive capacity to only the over-

wrapped cylinders. The effective cylinder count is

8 Medalist XE Family Installation Guide, Rev. A

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Seagate Stockage

Seagate

Seagate ST318405LW/LC Manuel utilisateur

Seagate

Seagate RealStor 5005 Series Manuel utilisateur

Seagate

Seagate Momentus Thin 7200 RPM Manuel utilisateur

Seagate

Seagate FreeAgent Pro Manuel utilisateur

Seagate

Seagate Cheetah ST3450657SS Manuel utilisateur

Seagate

Seagate Barracuda ST3808110AS Manuel utilisateur

Seagate

Seagate ST9160511NS - Constellation 7200 160 GB Hard... Manuel utilisateur

Seagate

Seagate HAWK 2LP ST31231N Manuel utilisateur

Seagate

Seagate SKYHAWK ST6000VX011 Manuel utilisateur

Seagate

Seagate ST336807FC - Cheetah 36 GB Hard Drive Manuel utilisateur

Seagate

Seagate 3.5-inch Pushbutton Backup External Hard... Manuel utilisateur

Seagate

Seagate BlackArmor NAS 110 Manuel utilisateur

Seagate

Seagate U Series 9 CE Manuel utilisateur

Seagate

Seagate HAWK 4 Famil Manuel utilisateur

Seagate

Seagate ST92014A Manuel utilisateur

Seagate

Seagate ST336704LW Manuel utilisateur

Seagate

Seagate Momentus 7200.1 PATA ST910021A Manuel utilisateur

Seagate

Seagate Momentus ST9100823A Manuel utilisateur

Seagate

Seagate Barracuda 7200.7 ST360019A Manuel utilisateur

Seagate

Seagate Barracuda Pro ST10000DM0004 Manuel utilisateur

Seagate

Seagate 10K.3 - Savvio 300 GB Hard Drive Manuel utilisateur

Seagate

Seagate MOMENTUS 5400.2 SATA Manuel utilisateur

Seagate

Seagate ST320014A Manuel utilisateur

Seagate

Seagate FIRECUDA ST2000DX002 Manuel utilisateur

Manuels Stockage populaires d'autres marques

QNAP

QNAP TS 32PXU Series Manuel utilisateur

LaCie

LaCie RUGGED RAID Manuel utilisateur

Freecom

Freecom CLS DOCK Manuel utilisateur

PNY

PNY Attache P-FD64MBATT3 Manuel utilisateur

HP StorageWorks MSL2024 Manuel utilisateur

OLT

OLT 6x6 Maximizer Manuel utilisateur

Transcend

Transcend JetFlash 160 Manuel utilisateur

LaCie

LaCie RUGGED MINI Manuel utilisateur

Thunderbolt

Thunderbolt 600 Manuel utilisateur

Panasonic

Panasonic LB-DH8 series Manuel

Intel

Intel RAID High Availability Manuel utilisateur

LaCie

LaCie 12big Thunderbolt 3 Manuel utilisateur

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuel utilisateur

Panasonic

Panasonic LKM-F931-1 Manuel utilisateur

Tabernus

Tabernus Enterprise Erase E2400 Manuel utilisateur

Rocstor

Rocstor COMMANDER 3F series Manuel utilisateur

HP P9000 Manuel utilisateur

Western Digital

Western Digital Ultrastar Data60 Manuel utilisateur