Seagate Hawk 2 ST12400N Manuel utilisateur
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
ST12400N/ND/NC
ST11900N/ND/NC
HAWK 2 Family:
. . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents
Introduction ........................................................ 1
Electromagneticinterference ............................ 1
Before you begin ................................................ 2
Installation overview .......................................... 7
Product repair information ................................ 9
Shipping ......................................................... 10
Product repair and return information............. 10
Technical support services ............................... 11
Drive specifications............................................ 14
Initial set-up information.................................... 17
Drive configuration............................................. 23
Drive installation................................................. 33
Drive Setup ......................................................... 37
© 1994 Seagate Technology, Inc. All rights reserved
Publication Number: 77767451, Rev. C.
March 1994
Seagate®,SeagateTechnology®andtheSeagatelogo
areregisteredtrademarksofSeagateTechnology,Inc.
HawkTM, SeaFAXTM, SeaFONETM, SeaTDDTM,
SeaBOARDTM aretrademarksofSeagateTechnology,
Inc.Otherproductnamesareregisteredtrademarksor
trademarks of their own.
Seagate reserves the right to change, without notice,
product offerings or specifications. No part of this
publication may be reproduced in any form without
written permission of Seagate Technology, Inc.
Hawk 2 Family Installation Guide, Rev. C 1
Introduction
Beforeattemptinganyinstallation,pleasereadthrough
all applicable sections of this document, including all
warnings and cautions.
Warning. This equipment generates, uses, and can
radiate radio frequency energy and if not
installedin accordancewith theseinstruc-
tions,maycauseinterferencetoradiocom-
munications.
Electromagnetic interference (EMI) con-
siderations
The drive(s) described herein, as delivered, are de-
signed for system integration and installation into a
suitable enclosure prior to use. As such, the drive(s)
described herein are supplied as a sub-assembly and
arenotsubjecttoSubpartJofPart15oftheFCCRules
and Regulations nor the Radio Interference Regula-
tionsoftheCanadianDepartmentofCommunications.
However,theunithasbeentestedusingpropershield-
ing and grounding and found to be compliant with the
ClassAlimits oftheFCCRulesand the Regulationsof
the Canadian Department of Communications.
2Hawk 2 Family Installation Guide, Rev. C
The physical design characteristics of the drive(s)
described herein, serve to minimize EMI radiation
when installed in an enclosure that provides reason-
able shielding. As such, the drive(s) are capable of
meeting the Class B limits of the FCC Rules and the
RegulationsoftheCanadianDepartmentofCommuni-
cations.
Note. It is the end users' responsibility to assure that
the drive(s)describedhereinmeettheappropri-
ate EMI requirements of their system. Shielded
I/Ocablesmayberequirediftheenclosuredoes
notprovideadequateshielding.IfI/Ocablesare
externaltotheenclosure,shieldedcablesshould
beused,with theshieldsgroundedto theenclo-
sure and to the host controller.
Before you begin
Verify that the system is switched off and discon-
nected from main power before any installation is
attempted.
Protect yourself, the drive, and your valuable pro-
grams and data by reading the following cautions
and warnings.
Hawk 2 Family Installation Guide, Rev. C 3
•Donotunpackdrive fromitsstaticshieldedbaguntil
you are ready to install it in the system.
•Always handle the drive by the frame or casting.
•Do not touch printed circuit board (PCB) or the I/O
connector pins.
•Never apply pressure to the PCB or to the drive top
cover.
•Donottamperwith sealedtopcover.Doingsovoids
your warranty. The drive contains no user service-
able components. See Product Repair section for
moreinformation.
•Visually inspect the shipping container for any obvi-
ous damage.
•Inspectdriveforpossibleshippingdamage.Allclaims
of this type should be filed promptly with the trans-
porterinvolved.Saveoriginalpackingmaterialstobe
used when reshipping.
•When transporting or shipping a drive or system,
please ensure that they are correctly packed in
originalSeagate approved(or equivalent)container
and shipped via an air-ride carrier experienced in
handling computer equipment.
•Verifyallpartslistedonshippingbillarereceivedwith
theequipment. Discrepanciesordamage shouldbe
reported to the shipping company.
4Hawk 2 Family Installation Guide, Rev. C
Caution. Thecircuitassembliesandcomponentscon-
tained in this equipment can be degraded or
destroyedbyElectrostaticOverstress(EOS)
or by Electrostatic Discharge (ESD).
Static electrical charges can accumulate
quickly on personnel, clothing and synthetic
materials.Theelectrostaticfieldsduetothese
charges when brought in close proximity to
susceptible circuit assemblies and compo-
nents, can result in degraded reliability or
immediatefailureof the affectedcomponent
or assembly.
Toinsureoptimumreliableequipmentopera-
tion, it is required that technical support per-
sonnel discharge themselves by wearing a
grounding strap around the wrist and be
connectedtoagroundingterminalwhilework-
inginthevicinityof,andwhilehandlingEOS/
ESDsusceptibleassemblies/parts.Ifunavail-
able,ground yourselffrequently bytouching
the metal chassis of the system before han-
dling any components (this helps only if the
system is connected to a ground).
Avoid
static-inducing carpeted areas.
This proce-
dure is especially important when handling
printed circuit boards (PCBs).
Hawk 2 Family Installation Guide, Rev. C 5
Safety instructions
1. The disc drive(s) are to be installed in a customer
suppliedenclosurewherethesurroundingairdoes
not exceed 50oC.
2. Four (4) 6-32 UNC-2A screws are required for
installation. Maximum screw length into side of
drive is 0.15 inches (3.81 mm). Maximum screw
lengthintobottomis0.20in.(5.08 mm).Maximum
screw tightening torque is 8.0 in-lb (0.90 NM) with
minimumthreadengagementof0.12in.(3.0mm).
3. Thepower requirementsare showninSection 1.0
ProductInformation.
4. The power supply must satisfy the safety require-
ments for SELV (Safety Extra Low Voltage) cir-
cuits.
5. Service is to be provided by trained Seagate ser-
vice personnel.
6. The incorporation of the disc drives listed in this
guide into a customer enclosure must meet the
appropriate safety requirements of the country in
which it is used (e.g. UL 1950, CAN/CSA-C22.2
No.950-M89,DINVDE0805/05.90andEN60950:
1988 (IEC 950).
6Hawk 2 Family Installation Guide, Rev. C
Sicherheitsanleitung
1. DäsGerätisteinEinbaugerät,vorgesehenfüreine
maximale Umgebungstemperatur von 50oC.
2. Zur Befestigung der Drive werden 4 Schrauben
benötigt (6-32 UNC-2A). Die maximale Länge der
Schrauben in der unteren Seite des Chassis darf
nicht mehr als 0.20 in (5.08 mm) betragen, die in
der oberen 0.15 in (3.81 mm). Maximalle
Schraubenaziehung Von 8.0 in-lb (0.90 NM) mit
minimalem Gewindeansperuch 0.12 in. (3.0 mm).
3. Die Versorgungsspannungen werden im Kapitel
1.0 (Produkt Information) gezeigt.
4. Die Versorgungsspannung muss SELV entspre-
chen.
5. AlleArbeitendürfennurvonausgebildetemSeagate
Service-Personal durchgefürhrt werden.
6. Der Einbau des Drives muss den Anforderungen
gemässDINVDE0805/05.90oderEN60950:1988
(IEC 950).
Hawk 2 Family Installation Guide, Rev. C 7
Installation Overview
Installation of the drive can be divided into distinct
phases as outlined below. Some of these may not be
applicable to your particular installation requirements.
Refer to the individual drive installation sections for
specific information on your drive model.
•Driveconfiguration:Theusermustselectwhichof
thedrivefeaturesareappropriatetoenableforinstal-
lationintheirsystem.Thisisdonebywayoftheuser
configuration jumpers found on the drive PCB.
•Mechanical installation: After setting up the drive
configuration the drive must be mechanically in-
stalled into the host system and the power and
I/O cables attached. Previously mentioned precau-
tions should be observed
•SCSI drives should not be defined in the CMOS:
The SCSI Host adapter has its own BIOS to handle
the Input/output procedures. The CMOS setting for
SCSI drive is either drive type zero, or the "no drive
installed"option.
8Hawk 2 Family Installation Guide, Rev. C
•Low-level formatting: After the drive has been
properly configured for the system, it does not need
to be low-level formatted, as this has been done by
the factory and does not require this step during
installation. (The low-level format writes the sector
boundariesandtrackinformationtothedrive).Defect
managementinformationisreadfromthedrivebythe
host system when required in the installation proce-
dure. If an installed drive is low-level formatted, all
user data stored on the drive will be lost.
Note. SeagateTechnologyassumes noliability for
lost user data.
•Partitioning and high level formatting: A drive
canbesub-dividedinto"partitions"whichbehaveas
individualdriveswithinthesystem.Seeyoursystem
documentation. Present day drive installation pro-
grams have menus that lead you through these
installationprocedures.
Ce manuel convient aux modèles suivants
5
Table des matières
Autres manuels Seagate Stockage
Seagate
Seagate Barracuda ST12550W Manuel utilisateur
Seagate
Seagate ST3000VX000 Manuel utilisateur
Seagate
Seagate ST31000322CS - Pipeline HD 1 TB Hard Drive Instructions d'utilisation et de sécurité
Seagate
Seagate ST34342A - Medalist 4.3 GB Hard Drive Manuel utilisateur
Seagate
Seagate FireCuda 520 Manuel utilisateur
Seagate
Seagate Cheetah 10K.7 SCSI Manuel utilisateur
Seagate
Seagate GoFlex Satellite Manuel utilisateur
Seagate
Seagate ST425 Manuel utilisateur
Seagate
Seagate Medalist 4340 Manuel utilisateur
Seagate
Seagate ST31200W Manuel utilisateur
Seagate
Seagate BARRACUDA 50 Manuel utilisateur
Seagate
Seagate ST6000VN0001 Manuel utilisateur
Seagate
Seagate ES.2 - Barracuda Enterprise 750GB SATA/300 7200RPM 32MB Hard... Instructions d'utilisation et de sécurité
Seagate
Seagate ST3160812SV Manuel utilisateur
Seagate
Seagate Enterprise Capacity Manuel utilisateur
Seagate
Seagate FreeAgent Desktop 500GB Manuel utilisateur
Seagate
Seagate Video 3.5 HDD Manuel utilisateur
Seagate
Seagate 600 SSD Manuel utilisateur
Seagate
Seagate EE25 Series Manuel utilisateur
Seagate
Seagate Duet Manuel utilisateur
Manuels Stockage populaires d'autres marques
Spectra Logic
Spectra Logic T-Series Spectra T50e Manuel utilisateur
Panasonic
Panasonic LKM-F931-1 Manuel utilisateur
Tabernus
Tabernus Enterprise Erase E2400 Manuel utilisateur
Rocstor
Rocstor COMMANDER 3F series Manuel utilisateur
HP
HP P9000 Manuel utilisateur
Western Digital
Western Digital Ultrastar Data60 Manuel utilisateur