GSM-SP11_Users_Manual_EN_v1_06.docx strana 1 / 5
SP11 – User manual
1. Introduction
GSM-SP11 (for short SP11) is device for remote control and monitoring, SP11
uses GSM network for communication. SP11 has 8 digital outputs ,that can be
remotely switched on/off or generate pulse. SP11 has 7 digital inputs.If input
change it´s own state SP11 can react on it via sending SMS message or by voice call.
And 2 analog inputs (clamps A1+, A1- and A2+, A2-), those can be set for
measuring current (0 to 20 mA), voltage (0 to 10 V) or temperature measurment
for different kinds of temperature sensors..
Detailed information about SP11 activity can be stored in device. Functions and
names of inputs/outputs,phone numbers,password etc. are customizable through PC
with USB cable or remotely by GPRS through program SeaConfigurator. This
configuration program is possible download for free from www.seapraha.cz (in search
type in „Configurator“). Lower part of the box has integrated DIN rail and SP11 can
be easily mount into switchboard.
(1) SIM card holder (under detachable cover)
(2) USB conector type B (under detachable cover) krytkou)
(3) digital outputs (Y)
(4) DIN rail holder
(5) power supply 8 to 30 VSS
(6) LED indication of outputs
(7) LED indication of operational status
(8) LED indication of inputs
(9) analog inputs
(10) GSM antenna connector
(11) digital inputs (X)
2. Package
Content
1pcs GSM-SP11
1pcs GSM antenna (order code GSM-ANT05S)
1pcs USB cable A-B (order code HW-11.02.8818)
Accessories – Must be ordered separately!
Box with power supply GSM-SP-BOX-MV
Temperature sensor GSM-C-T2 … range from -20 °C to +50 °C (integrated KTY81-
210)
Temperature sensor GSM-C-T3 … range from -40 °C to +180 °C (integrated Pt1000)
3.
Installation
Caution!
Before connecting analog input make sure you have the right configuration for
it!(typically voltage/current input).
1. Before powering up SP11 insert activated SIM card into SIM card reader (under
detachable cover) and mount the GSM antenna. SIM card is inserted to the reader
by slope side heading down and contacts heading to the middle of the SP11.
Recognize right insert by mechanical click. To remove the SIM card - press the
SIM card in direction into the
SP11
until mechanical click. The SIM card can be
the freely removed.
2. Connect device to DC power supply. DC voltage must be 8-30Vss, connect to
clamps + and – and turn on the power supply.
3. If power is good, green LED PWR goes on.After about 20 sec blue LED GSM
will starts flashing every 3 sec.
4. Send SMS message in format 1234 STATE to the SP11´s phone
number. Device will respond with state SMS message in format
„GSM-SP11: Y1=vyp......X1=vyp....AP=12V....“.For further
configuration you have to use program SeaConfigurator(see
below).
5. Install program SeaConfigurator, It´s latest version is available for
download on www.seapraha.cz (in search type in „Configurator“).
Downloaded program install according to the instructions of
installation guide. USB driver will be installed automatically.
6. Run program SeaConfigurator (Start Programs SEA
Configurator Configurator). Connect device to PC through USB
cable, which is included in package.During configuration through
USB cable you have to have connected power supply to SP11!Load configuration
from the device by clicking on button [From station]. In tab „Settings“ –
„Users“ Type in your phone number and name.
7. Customized configuration must be uploaded to the SP11.
Click on button [To the station]. If you let the USB cable
connected,you can watch in tab „Monitoring“ current status
of the SP11 and statuses of it´s own inputs and outputs.
8. Digital inputs (signals to the SP11) connect to clamps X1 to
X7 and digital outputs (signals out from the SP11) connect
to clamps Y1 to Y8. Recommended wiring of those signals are
written in chapter „Hardware“.when any input changes state,SP11 can send SMS
message to you phone in format e.g. “Input1 is ON” (Depends on configuration).
4. Technical specifications
Dimensions
Height
(without
GSM
v 90 mm
Depth (from
h 80
*1)
mm
Power supply
Current ICC VCC = 12V
0,14 0,5 *2)
A
Average
power
PCC 1,67 6 W
Digital DC
inputs (any
polarity)
Voltage
log. H
|VIN| 4 12 30 V
Voltage
log. L
|VIN| <2
4 V
Digital
outputs DC,
AC
Voltage DC
VOUTDC 50 VDC
Voltage AC
VOUTAC 35 VAC
Current DC
IOUTDC 90 mA
Current AC
IOUTAC 90 mA
Anolog
inputs A1 a
A2:
(customizable)
Number - 1 -
Measured unit - Analog input with customizable conversion ,
adjustable for different measurements
0 to 10V;
0 to 20mA (input resistance 75);
temperature sensors:
KTY (-50 až +150°C);
Pt100 (-100 až +300°C);
Pt1000 (-100 až +300°C);
-
Voltage max
12 V
input
Voltage input 100 k
input
RIN Current input 75
Resolution
- 12 bits
*1) We can make box smaller „Slim“ design on request.
*2) Average consumption is when GSM network is connected and battery is charged.
Every output switched on increases consumption by 1mA. Max consumption is short
when device is downloading data via GPRS and weak signal and discharged battery.
SP11 is designed for installation into switchboard with min. protection at least IP44!
5. Hardware
Clamps A1-, A1+ a A2-, A2+ (analog input):
… voltage input 0 to +10 V (clamp A1+ / A2+ connect to higher potencial!)
… current input 0 to +20 mA (clamp A1+ / A2+ connect to higher potencial!)
… temperature sensor KTY81-210, Pt100, Pt1000 (order of connection doesn´t
matter)
1. Před vložením SIM karty do zařízení SP11 doporučujeme pro
první spuštění vypnout zadávání „PIN kódu“!
2. Vložte aktivovanou (= zavolat alespoň na infolinku operátora) SIM kartu
do libovolného mobilního telefonu a vypněte požadavek zadání PINu. U
většiny mobilních telefonů naleznete tuto volbu v menu „Nastavení
zabezpečení telefonu“.
3.
4. Pro skutečný provoz můžete mít PIN povolený pro zvýšení bezpečnosti zařízení, ale
následující jednoduchý postup prvního spuštění funguje pouze se SIM kartou bez
a. Before inserting the SIM card into the
SP11
device, we
recommend to turn off setting of the “PIN code”!
b. Insert the active SIM card (= at least one call was made) to any mobile
telephone and turn off the requirement of setting the PIN. On most
mobile telephones, this option can be found in menu “Setting the
telephone protection”. or “Setup -> Security -> PIN control”.
