schroff 23001-701 Manuel utilisateur
VXS Backplane 23001 – 701 User Manual
Assembly Instructions & general Information
1. Warning: Only important if V1 and V2 are used
If the +V1 and +V2 voltage rails are tied to ground and the +12V power is used, the nominal voltage
between the +12V and the -V1 and -V2 power rails is 60 volts. With voltage tolerances, the 60 volt
maximum is exceeded. Additional protection might be needed to comply with local and national regulatory
agencies.
2. Mechanical Mounting: Attach the backplane through the mounting holes in at least every second
connector position at top and bottom using M2,5 screws and isolating washers.
3. Chassis GND: If noise reduction shall be achieved by connecting digital GND to Chassis GND, use
conductive washers instead of isolating ones. Spring washers are recommended instead of flat washers.
Creepage and clearance between screw and GND are in accordance with EN60950 is maintained by
layout when using isolating washers.
4. Live Insertion: Schroff VME64x backplanes fulfil the requirements of the VME Live Insertion standard
VITA 1.4. The LI/I* (Live Insertion IN) is an active low input signal to a VME64x LI board that acts to
enable/disable the on-board power control logic. A set of two pins per slot for LI/I* and GND spaced by
100mil is optional available to use micro-connectors to connect the signal to a radial power control module.
5. Daisy Chain: Schroff VME64x Backplanes are equipped with Electronic Automatic Daisy Chain.
OR gate
truth table
A B Y
1 1 1
1 0 1
0 1 1
0 0 0
Slot 1 Slot 2 Slot 3 Slot 4
Electric Automatic Daisy Chain
BUS GRANT and IACK
A20
A21
R: 82k
active LOW signal
propagating starts
from System
controller
Grant signal propagates as a "baton" from board to board. Board which has
requested the bus, stops propagating of the grant signal.
If a board is removed, the broken chain must be closed.
IN
OUT
loop from IN to OUT must be closed if board is not inserted
R: 82k
6. Dimensions Height 262.05 mm, Width 171,72mm
7. Assembling of Power Cables: If an open frame power supply is used instead of pluggable PSU´s, please
pay attention by connection the power cables to the power bugs. M4 cable lugs should be used to connect
the cables from the PSU to the powerbugs on the backplane. Maximum 2 cables are allowed per
powerbug. Please assemble the cable lugs with the flat side to the power bug to ensure the correct
isolation distance between unisolated part of the power cable and unisolated parts of the backplane.
Powerbug
Cable
Correct orientation
Powerbug
Cable
Wrong orientation
Schroff GmbH, Febr. 2006; Document#: 73972-125, Rev.: 51
www.schroff.de Page 1 of 3
VXS Backplane 23001 – 701 User Manual
Customer Drawing (Rear View)
3.3V
GND
+5V
GND
+5V
Stby
GND
+12V
GND
-12V
GND
V
1/V2 Utilit
y
8X1 9X1
J1
V
ME Bus
V
ME Bus
IPMB
High-Speed serial links in
accordance to VITA 41
Schroff GmbH, Febr. 2006; Document#: 73972-125, Rev.: 51
www.schroff.de Page 2 of 3
VXS Backplane 23001 – 701 User Manual
Electrical Interface
Utility Connector
Top view on connector
A B
6
5
4
3
2
1
A B
6 nc nc
5 nc -12V
4 +12V 3,3V
3 GND +5V
2 nc. ACFAIL*
1 SYSFAIL* SYSRESET*
Cable assy:
Schroff part #: 23204 – 115 (350mm)
Schroff part #: 23204 – 116 (600mm)
free connector: ERNI part #: 044663
IPMB Connector
Top view on connector
Pin Signal
1 SCL
2 GND
3 SDA
4 Vsm
5 nc
Molex part#:
board connector: 53398-0590
free connector: 51021-0500
crimp contact: 50079-8100
(AWG 26-28, bag)
Vsm (Power) is connected
to +5V standb
y
Cable assy 750mm, other end without terminals:
Schroff part#: 23204 - 113
V1/V2 Connector pinout
-V2 +V2
-V1 +V1
V1/V2 auxiliary power supplied to the
VME64x backplanes shall remain within
the limits of 38V to 75V, including
regulation variation, noise and ripple
frequencies to 20 MHz.
Molex part#:
board connector: 43045-0418
free connector: 43025-0400
crimp contact: 43030-0007
(AWG 20-24,
tin plated, bag)
P47 connectors (8X1, 9X1)
Pin# Si
g
nal Name Pin# Si
g
nal Name
1+5V 25 GA0
2+5V 26 RESERVED
3+5V 27 GND (EN#)
4+5V 28 GA1
5GND 29 nc
5GND 30 +5V (V1 SENSE)
7GND 31 GA2
8GND 32 nc
9GND 33 +3,3V (V2 SENSE)
10 GND 34 GND (GND Return)
11 GND 35 V1 SHARE
12 GND 36 +12V (V3 SENSE)
13 +3,3V 37 IPMB_SCL
14 +3,3V 38 PSU (1-4) DEG#
15 +3,3V 39 INH#
16 +3,3V 40 IPMB_SDA
17 +3,3V 41 V2 SHARE
18 +3,3V 42 PSU (1-4) FAL#
19 GND 43 IPMB_PWR
20 +12V 44 V3 SHARE
21 -12V 45 PE
22 GND (Signal return) 46 AC Input neutral
23 nc 47 AC Input line
24 GND
J1 Connector
Top view on connector
Pin Si
g
nal
1 +5V
2 GND
3 nc
4 INH#
5 FAL#
Molex part#:
board connector: 53398-0590
free connector: 51021-0500
crimp contact: 50079-8100
(AWG 26-28, bag)
Vsm (Power) is connected
to +5V standb
y
Schroff GmbH, Febr. 2006; Document#: 73972-125, Rev.: 51
www.schroff.de Page 3 of 3
Autres manuels schroff Matériel informatique
Manuels Matériel informatique populaires d'autres marques
EMC2
EMC2 VNX Series Manuel du propriétaire
Panasonic
Panasonic DV0PM20105 Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuel utilisateur
Raidon
Raidon iT2300 Manuel utilisateur
National Instruments
National Instruments PXI-8186 Manuel utilisateur
