Schlage HK-CR Manuel utilisateur
HK-CR
Terminal User’s Guide
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in
accordance with the Installation Manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at the user’s
own expense.
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numerique de la classe A respecte toutes les exigences du Reglemente sure le materiel brouilleur du Canada.
© 2014 Allegion
Document Part Number: 70100-6008 – Revision 3.3 – 07/16/14
HandPunch is a trademark of Schlage Biometrics, Inc.
The trademarks used in this Manual are the property of the trademark holders. The use of these trademarks in this Manual should not
be regarded as infringing upon or affecting the validity of any of these trademarks.
Schlage Biometrics, Inc. reserves the right to change, without notice, product offerings or specications.
No part of this publication may be reproduced in any form without the express written permission from Schlage Biometrics, Inc.
iii
Table of Contents
Introduction 3
HandKey CR 3
Biometrics 3
Principle of Operation 3
The HandKey CR Reader 3
Specifications 5
Options 6
UL Compliance 6
Planning an Installation 7
Site Preparation7
HandReader Placement 7
Wiring 8
Power Input 8
Battery Backup 8
Earth Ground and Shielding 9
Earth Ground All Units 10
Carry a Ground Line to Each Unit 11
Door Control Output12
Lock Output Mode 12
Card Reader Emulation Mode 12
Outputs 12
Networking and Communications 15
Stand-alone HandReader 15
Master or Remote HandReader in a HandReader Network 15
Remote HandReader in a HandReader Network Connected to a Host PC 15
Remote HandReader Connected to a Host PC via Optional Modem 16
Remote HandReader Connected to a Host PC via Optional Ethernet 16
Printer16
Mechanical Installation 17
Wall Plate Installation17
Mounting the Wall Plate 18
Routing the Wiring 18
Attaching the HandReader 19
Closing the HandReader 20
Wiring Connections 21
iv
Wiring Connections 21
Wiring Examples 21
Erasing the Memory 29
Erasing HandReader Memory 29
Enter a Command Menu 31
If No One is Enrolled in the HandReader31
If Users are Enrolled in the HandReader 31
Navigating Command Menus 32
Programming the HandReader 33
Authority Level 34
Programming Order 34
System Management and Maintenance 35
Design an ID Numbering System 35
Service Menu 37
Navigating the Service Menu 37
Service Commands 37
Calibrate 38
Status Display 38
Network Status 38
Setup Menu 39
Navigating the Setup Menu 39
Setup Commands 39
Set Language 41
Set Date Format 41
Set Time and Date 41
Set Address 41
Set ID Length 41
Set Facility 42
Aux Out Control 42
Set Reader Mode 43
Set Serial 43
Set Duress Code 43
Set Beeper 43
Upgrade 43
Management Menu 45
Navigating the Management Menu 45
Management Commands 45
List Users 45
HandKey II Manual
v
Data From Network 46
Data To Network 46
Enrollment Menu 47
Preparation 47
User Education 47
Proper Hand Placement 48
Left Hand Enrollment 48
Read Score 48
Navigating the Enrollment Menu 49
Enrollment Commands 49
Add User 49
Remove User 49
Security Menu 51
Navigating the Security Menu 51
Security Commands 51
Set User Data 53
Set TZ Table 53
Reject Threshold 54
Set Passwords 54
Clear Memory 54
Special Enroll 54
HandReader Maintenance 55
Cleaning the Hand Reader 55
User Score 55
Appendix A: Tips for a successful Installation 57
Location and Installation 57
HandReader 57
Enrollment 58
Communication 58
Appendix B: Noted Board Configuration Differences 59
Terminal Block Labeling 60
Terminal Block Layout 61
Memory Reset 62
Appendix C: Old Board Configuration Information 63
Attaching the HandReader 63
Grounding 65
Wiring Examples 66
End of Line Termination 74
Appendix D: Troubleshooting Guide 77
vi
Communication Method 74
Erasing the HandReader Setup 75
Erasing the HandReader Setup and User Database 75
Appendix D: Troubleshooting Guide 77
Display Messages During Verification 77
Beeper and LED Status During Verification 78
Glossary 79
Limited Warranty 81
3
Introduction
The HandKey CR is Schlage Biometrics’ fourth generation biometric access control
HandReader.1The HandReader records and stores the three-dimensional shape of the
human hand for comparison and identity verification. Upon verification, the HandReader
produces an output that can unlock a door, send card format data to an access control
panel, or communicate with a host computer. The HandReader also has auxiliary inputs
and outputs that can be used to control other systems such as CCTV cameras and
alarms.
Biometric is a term describing the automatic measurement and comparison of human
characteristics. While its origins are ancient, the evolution of advanced scanning and
microprocessor technology brought biometrics into everyday life. Electronic hand
geometry technology first appeared in the 1970s. Schlage Biometrics Inc., founded
in 1986, built the first mass-produced hand geometry readers and made biometric
technology affordable for the commercial market. Today, Schlage Biometrics’ products are
in use in every imaginable application from protecting cash vaults to verifying parents in
obstetric wards.
The HandReader uses low-level infrared light, and a CMOS camera to capture a three-
dimensional image of the hand. The HandReader then converts the image to a 9 byte
electronic template, and stores the template in a database with the user’s information.
To gain access, the user enters his or her ID number at the HandReader’s keypad or
uses an external card reader. The HandReader prompts the user to place his or her hand
on the reader’s platen.2The HandReader compares the hand on the platen with the user’s
unique template. If the images match, the HandReader unlocks the door or sends the
user’s ID number to a third-party access control panel for verification.
The HandReader is an intelligent access control system that can operate as a stand-
alone unit, in a network with other HandReaders, or in a network with a host computer.
Refer to Figure 1-1 when reviewing the information in this section.
1 For the sake of using a consistent name throughout the manual, the HandKey CR is referred to
as the HandReader for the remainder of this manual.
2 The platen is the flat surface at the base of the HandReader (see Figure 1-1). This is where
users place their hands for enrollment and verification. It has guide pins to position the fingers
during use.
HandKey CR
Biometrics
Principle of
Operation
The HandKey
CR Reader
Introduction
4
5
46
F1
8
79
F2
0
No Enter
2
13
Clear
*#
Yes
No
Recognition Systems Inc.
PL ATEN AND GUIDE PINS
HAND
PLACEMENT
DISPLAY
LCD DISPLAY
FUNCTION
KEYS
VERIFICATION
LIGHTS
NUMERICAL
KEYPAD
Figure 3-1: The HandKey CR
The HandReader has an integrated keypad for ID entry and reader programming. It
has two function keys (F1 and F2) that can be set to activate external devices such as
a doorbell or an automatic door. The Clear and Enter keys assist in data entry and
programming.
Four different features assist the user with hand placement and read verification.
1. A light emitting diode (LED) hand placement display on the HandReader’s top panel
assists users with hand placement on the platen.
2. A liquid crystal display (LCD) shows operational data and programming menus.
3. “Red light/green light” verification LEDs quickly inform users if their verification
attempts were accepted or rejected.
4. An internal beeper provides audible feedback during keypad data entry and user
verification.
HandKey II Manual
5
Table 3-1: Specifications
Size: 8.85 inches wide by 11.65 inches high by 8.55 inches deep (22.3
cm)
22.3 cm wide by 29.6 cm high by 21.7 cm deep
Power: 12 to 24 VDC or 12 to 24 VAC 50-60 Hz, 7 watts
Weight: 6 lbs (2.7 kg)
Wiring: 2 twisted-pair, shielded, AWG 22 or larger (such as Belden
82732)
Temperature: -10C to +60C – non-operating/storage (14F to 140F)
0C to 45C – operating (32F to 113F)
Relative Humidity
Non-Condensing:
5% to 85% – non-operating/storage
20% to 80% – operating
Verification Time: 1 second or less
Memory Retention: 5 years using a standard internal lithium battery
Transaction Buffer: 5120 transactions
ID Number Length: 1 to 10 digits
Baud Rate: 300 to 28.8 K bps
Communications: RS-232, RS-422, RS-485 2-wire, optional Ethernet, optional
Modem
User Capacity: 512 users expandable to 259,072
Card Reader Input: Proximity, Wiegand, Magnetic Stripe, Bar Code
(5 VDC provided by HandReader)
Card Reader Output: Wiegand, Magnetic Stripe, Bar Code
Duress Code: 1 leading digit, user definable
Door Controls: Request to Exit input, Door Switch input, Lock output
(open collector, 5 VDC present, sinks to ground, 100 mA max)
Alarm Monitoring: Tamper, Door Forced, Duress
Event Monitoring: There is a variety of monitoring options including events such
as: Invalid ID, Time Zone Violation, ID Refused, Try Again, Power
Failure
Time Zones: 62 total – 2 fixed, 60 programmable
Auxiliary Outputs 3 user definable
(open collector, 5 VDC present, sinks to ground, 100 mA max)
Specifications
Introduction
6
HandKey units have the following options available.
• Backup Battery Support See Technical Note 70200-0012 rev C
• Modem Communication See Technical Note 70200-0013 rev C
• Ethernet Communication See Technical Note 70200-0014 rev H
Hand Readers are UL Listed as stand alone units only (i.e. the card reader function
has not been evaluated by UL).
The HandKey ll has not been tested for UL 294 in an Outdoor configuration.
recyclable
Options
UL Compliance
Table des matières
Autres manuels Schlage Terminal tactile
Manuels Terminal tactile populaires d'autres marques
Wincor Nixdorf
Wincor Nixdorf iPOS plus Advanced Manuel utilisateur
Ingenico
Ingenico AXIUM EX4000 Manuel utilisateur
Heisei Electronics
Heisei Electronics Q-POS 815 Manuel utilisateur
Amano
Amano MTX-15 Manuel utilisateur
FLOWBIRD
FLOWBIRD CWT Compact Touch Manuel utilisateur
Demco
Demco SP7 Manuel utilisateur
