Schaller M30 Manuel utilisateur

User manual

humimeter M30

universal material moisture meter

version 1.1_en

2019

version 1.1

Operation and handling

Switching on: Press the button for three seconds.

Changing the calibration curve: or key.

Switching on the display lighting: Press the button briefly; the

lighting switches off automatically after approx. 20 seconds.

Pressing any key activates the lighting again and prolongs the

switch-off time to 4 minutes.

Switching off: Press the key for five seconds; the device

switches off after releasing the key. After approximately four

minutes the device switches off automatically.

Measuring procedure

Switch on the instrument by pressing the key for 3 seconds.

Select the appropriate calibration

curve using the arrow keys.

Hold the device in one hand and

press it onto the material well-

setted (4 kg compacting pressure).

The material pile has to be at least

10mm high!

The display shows the water

content immediately (large

numbers).

Calibration curves

Name

Description

empty 1 to 10

10 free calibration curves

reference

! Only for checking the instrument !

➢There are 10 free calibration curves available. These

calibration curves can be used for measuring special

products.

➢First of all the calibration curves have to be created!

➢On request Schaller GmbH can create customer-specific

calibration curves for your products.

Version 1.1

Design of the device

name of

calibration curve

rolling menu

resp. hold button

rubber

protection cover

ON-OFF button

measuring value

water content

measuring value

temperature

selection of

calibration curve

batteries slot

(flipside)

empty 1

version 1.1

Menu level overview

Type selection menu

Store menu

Main menu

Next calibration curve

Previous calibration curve

Power off

Watch last log

Save new value

Power off

Switch lower

Switch upper

Open this menu / Enter

Keypad symbols

Measuring window:

Rolling Menu

Power ON / OFF

Switch upper

Switch lower

Save

Hold

Autolog

Watch saved data

Enter supplier´s

data

Menu:

Enter

Switch upper

Switch lower

Exit

Enter numbers

Enter letters

Next or right

Left

Yes

Shift

Edit Logs

Manual Logs

Auto Logs

Clear Logs

Print Logs

Last Log

All Logs

Clear Logs

Send Logs

Manual Logs

Auto Logs

Clear Logs

Options

Date/Time

Emission ratio

Datalog Time

Language

Unlock

°C/°F

Calibrate

Userlevel

Light On time

Auto Off time

Materialcalib.

Adjust

Password

Reset

Status

Version 1.1

Changing the batteries

First of all remove the rubber protection cover. For that, hold the rubber

protection cover at the upper side and pull it over. If your humimeter is

provided with an optional USB port, remove the protection cap before. Press

with your finger onto the arrow of the battery cap and pull it back.

Remove the empty batteries. Put four new 1.5 Volt AA Alkaline batteries into

the device. Make sure that the position of the battery poles is correct. Press

down the batteries and close the cap.

Exemption from liability

For miss-readings and wrong measurements and of this resulting damage

we refuse any liability. This is a device for quick determination of moisture.

The moisture depends on multiple conditions and multiple materials.

Therefore we recommend a plausibility check of the measuring results. Each

device includes a serial number and the guarantee stamp. If those are

broken, no claims for guarantee can be made.

Care instructions

Do not drop the instrument or expose it to excessive temperatures. Only

clean the instrument with a dry lint-free cloth. The instrument is not

waterproof. The intervals for checking the instrument depend on your

operational demands and the required level of accuracy. For a fee, we can

carry out a calibration in our factory. On demand you will also receive a

calibration certificate.

Checking the calibration

We recommend checking the calibration of your humimeter M30 regularly.

For this check the device has to show a temperature between 20.0 and

26.0°C. Switch on the instrument and select the calibration curve „reference“

using the arrow keys. Hold the humimeter M30 in one hand right up in the

air. Please make sure that there is no material or anything similar in front of

the measuring plate. The shown measuring value should range between 3.0

and 3.6. If the shown value is out of this range, you have to carry out a

calibration (see instructions below).

version 1.1

Calibration

By a zero point adjustment you can correct a too

high deviation of the calibration check.

For that please proceed as follows:

Press the left key twice to reach the menu level.

Navigate to the menu item „Options“ using the

arrow keys. Confirm by pressing the button.

Select the menu item „Calibrate“ using the arrow

keys and confirm by pressing the key.

This menu item has to be unlocked. For that you

have to enter the 4-digit serial number of your

humimeter. You can find the serial number on the

top right edge of your display a short time after

switching on the instrument, or on the sticker in

the battery slot.

Press the third button as long as the black bar

stands on the first digit of the serial number. After

a waiting time of a few seconds the device accepts

the entered digit. Now the other 3 digits have to

be entered. When the 4-digit number has been

entered correctly (see picture), press the button

to confirm.

Hold the humimeter M30 in one hand up in the air

and make sure that there is no material in front of

the measuring field (black plate). Now press the

second button ( ) with one finger.

The calibration procedure will take a few seconds.

During that time, the instrument has to be held up

in the air and the measuring field must NOT be

touched.

The device is ready when the shown picture on

the right disappears automatically.

Version 1.1

!IMPORTANT! Please read

Common reasons for incorrect measurements:

•It is obligatory that the measuring instrument rests on an even

measuring area without any air space!

•The measuring depth of your humimeter M30 is 30 mm

•Please ensure that during the measurement there is NO metal or

anything similar within an area of 50 mm below the measured

material

•Wrong compacting pressure; please note the instructions (4 kg)!

•Product temperature out of application range

The application range is between 0°C and +40°C

•Discrepancy in temperature between device and material

Please ensure that the device and the material under test are

being stored at nearly the same temperature before measuring. A

high temperature difference has a negative effect on the stability

of the measurement results

version 1.1

Technical data

Measuring depth 30 mm

Resolution 0.1% water content ; 0.1°C ; 0.3°F

Operation temperature range 0°C to +40°C

Storage temperature -20°C to +60°C

Temperature compensation automatically

Memory for measured values approx. 10.000 measuring values

Menu languages English, German, Italian, French,

Spanish, Russian

Power supply 4 pcs. 1.5 Volt AA Alkaline batteries

(for approx. 900 measurements)

Switch off time after approx. 4 minutes

Power consumption 60 mA (with display lighting)

Display 128 x 64 matrix display,

with LED backlighting

Dimensions 147 x 75 x 30 mm

Weight 260g (incl. batteries)

Protection class IP 40

Scope of supply humimeter M30, 4 pieces 1.5Volt AA

Alkaline batteries, rubber protection

cover, user manual

Options data interface module incl. software

and cable, mobile printer (only with

option 1)

Table des matières

Autres manuels Schaller Instrument de mesure

Schaller

Schaller Humimeter BLW Manuel utilisateur

Schaller

Schaller humimeter FL1 Manuel utilisateur

Schaller

Schaller humimeter FS1 Manuel utilisateur

Schaller

Schaller SW1 Manuel utilisateur

Schaller

Schaller humimeter FS2 Manuel utilisateur

Schaller

Schaller humimeter PMZ Manuel utilisateur

Schaller

Schaller humimeter PM3 Manuel utilisateur

Schaller

Schaller humimeter BLL Manuel utilisateur

Schaller

Schaller humimeter FL1 Manuel utilisateur

Schaller

Schaller FSA Manuel utilisateur

Schaller

Schaller humimeter BMA Manuel utilisateur

Schaller

Schaller FL2 Manuel utilisateur

Schaller

Schaller humimeter WLW Manuel utilisateur

Schaller

Schaller humimeter GF2 Manuel utilisateur

Schaller

Schaller humimeter FLS Manuel utilisateur

Schaller

Schaller humimeter FLSO Manuel utilisateur

Schaller

Schaller GrandTune Manuel utilisateur

Schaller

Schaller humimeter SG1 Manuel utilisateur

Schaller

Schaller PMSA Manuel utilisateur

Schaller

Schaller humimeter FS4 Manuel utilisateur

Schaller

Schaller humimeter.com LM6 Manuel utilisateur

Schaller

Schaller RH2 Manuel utilisateur

Schaller

Schaller MS4 Manuel utilisateur

Schaller

Schaller humimeter LM5 Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur