SC&T VE05AL Manuel utilisateur
Smart Cabling & Transmission Corp. V1.0
VGA Extender
User Manual
Model : VE05AL
1 x 5 VGA & Stereo Audio Distribution Amplifier CAT5e
Extender, Transmiter
1
User Manual
VE05AL
Introduction
VE05AL is a VGA extender designed to use a cost-effective CAT5e UTP cable to carry the signal with
stereo audio signal and split the signals for 4 video & 4 audio outputs. Its RX unit has a built-in chainable
RJ45 output to connect another chainable RX for more working distance and VGA outputs. It's a optimal
solution used in Shopping malls, airports, train & bus stations, boardrooms, and tradeshows...etc.
Features
Extends and split a VGA into 5 ones.
Extends and splits a VGA into multiple ones.
Built-in equalization, gain adjustment, chainable CAT5 output at VE02ALR remote unit.
Resolution up to 1920x1200@60Hz.
Signal extension up to 300M over a CAT5e cable.
Build-in VGA loop-out for a local display.
Installation View
2
User Manual
VE05AL
Panel View
VE05ALT
VE02ALR
RJ45 Define
Link Cable (TIA/EIA-568-B)
1. Orange-white
Red +
2. Orange
Red -
3. Green-white
Green +
4. Blue
Audio -
5. Blue-white
Audio +
6. Green
Green -
7. Brown-white
Blue +
8. Brown
Blue –
VE02ALT/VE05ALT LED
Blue (front panel): power on/off
RJ45 LED (Link cable connector)
Green: status (Refer the below)
Yellow: status (Refer the below)
LED status indication
CH1 ~ CH4
Green on/off:
VGA Signal
Green flash:
EDID checksum error
Yellow on:
Use monitor DDC
Yellow off:
Use built in DDC
Yellow flash:
monitor EDID checksum Error
Yellow, Green, Blue all flash:
Memory error
3
User Manual
VE05AL
VE05ALT local unit EDID set up
Setup Monitor EDID:
When Yellow LED off, press “SETTING” button until Blue LED flash, then release
the “SETTTING” button, yellow LED will be on.
Setup Built in EDID:
When Yellow LED on, press “SETTING” button until Blue LED flash, then release
the “SETTTING” button, yellow LED will be off.
Reset factory default:
First to unplug the power, then press “SETTTING” button until reconnect
power and Blue LED flash.
Auto Backup EDID:
Change new monitor, it will start the monitor EDID backup.
VE02ALR Remote unit adjustment
EQ
equalization (sharpness)
Gain
signal boost (brightness)
VE02ALR LED
Blue (front panel): power on/off
RJ45 LED (Link cable connector)
Green: signal lock (LED on)
Caution
The cabling must away from any equipment with electromagnetic wave, i.e.: microwave, radio
equipment, high voltage lines.
Installation Tips
Due to the inside of CAT5 cable that the pairs of wires are twisted at different rates, AND the different
quality on cable itself and installation that will cause different signal arrival time at each pair. If there
are big different at arrival time, that will cause RGB skew status. This is seen on the monitor as separation,
or lack of convergence in colors. Normally it happens on long CAT 5 cable runs.
4
User Manual
VE05AL
Recommend to use following cabling way to reduce skew status, to add special made “skew immunized
adaptor”, 2 pieces included at the package.
CAUTION
To avoid display equipment damaged, be sure to make correct cable connection and power for VE02ALT,
VE05ALT, and VE02ALR before connecting VE02ALT, VE05ALT, and VE02ALR.
Installation Cable
Video Link cable using hi quality CAT5E UTP/STP or CAT6 UTP cable.
Please noted STP cable could enhance noise rejection, but also less transmission range and picture
sharpness quality.
5
User Manual
VE05AL
Specification
ITEM NO.
VE05ALT
VE02ALR
Support
Compliance
TTL
Max. Video Resolution
1920 x 1200@60Hz
Max. Transmission Distance
300M over CAT5e or Greater
Video Bandwidth
700 MHz, -3dB (Remote 350MHz, -3dB)
150MHz
Audio Bandwidth
20 to 20KHz, -3dB
Frequency
Horizontal at 30 to 95KHz, Vertical at 50 to 180Hz
Ports & Interfaces
Video Input
1 x DB15 (75Ω, 0.7Vp-p)
1 x RJ45
Video Output
4 x RJ45
1 x DB15 (75Ω, 0.7Vp-p)
Video Loop-out
1 x DB15 (75Ω, 0.7Vp-p)
1 x RJ45
Audio Interface
2 x 3.5mm Stereo Phone Jack (10KΩ,
3Vp-p)
1 x 3.5mm Stereo Phone Jack (10KΩ, 3Vp-p)
Power
Power Supply
DC 12V 2A
DC 12V 2A
Power Consumption
700mA (Max)
700mA (Max)
Ambient Temperature
Operation
0 to 55℃
Storage
-20 to 85℃
Humidity
up to 95%
Physical Characteristics
Dimensions
125 x 95 x 30mm
88 x 95 x 30mm
Weight
275g
205g
Table des matières
Autres manuels SC&T Extenseur
SC&T
SC&T HE01SE Manuel utilisateur
SC&T
SC&T YE02DAL Manuel utilisateur
SC&T
SC&T YE10DAL Manuel utilisateur
SC&T
SC&T HKM01T-4K Manuel utilisateur
SC&T
SC&T IP05I Manuel utilisateur
SC&T
SC&T HE05BT Manuel utilisateur
SC&T
SC&T HE02EIR Manuel utilisateur
SC&T
SC&T HE02ER Manuel utilisateur
SC&T
SC&T VW01HA Manuel utilisateur
SC&T
SC&T HE01F Series Manuel utilisateur
SC&T
SC&T HE01F-4K Manuel utilisateur
SC&T
SC&T HE20E Manuel utilisateur
SC&T
SC&T Audio Extender Series Manuel utilisateur
SC&T
SC&T DKM01 Manuel utilisateur
SC&T
SC&T HE02PT Manuel utilisateur
SC&T
SC&T HKM01-4K Manuel utilisateur
SC&T
SC&T VE01HA Manuel utilisateur
SC&T
SC&T HUE03T-4K Manuel utilisateur
SC&T
SC&T IP01 Manuel utilisateur
SC&T
SC&T HD401F-5M Manuel utilisateur
