SC&T HKM02B-4K Manuel utilisateur

Autres manuels pour HKM02B-4K

1

Table des matières

Autres manuels SC&T Extenseur

Manuels Extenseur populaires d'autres marques

SY

SY HDBT-60T Manuel utilisateur

Appsys ProAudio

Appsys ProAudio ADX-16 Manuel utilisateur

Atlona

Atlona RS232 Manuel utilisateur

IDK

IDK OPF-TH1000-A Manuel utilisateur

Enable-IT

Enable-IT 824WP Manuel utilisateur

Worx

Worx Landroid RadioLink WA0864 Fiche technique

TP-Link

TP-Link TL-WA730RE Manuel utilisateur

Camplex

Camplex CMX-HDMI-SFPL Manuel utilisateur

Marmitek

Marmitek MegaView70 Manuel utilisateur

Samsung

Samsung SCS-26UC4 Manuel utilisateur

Foxun

Foxun SX-GES24 Manuel utilisateur

MuxLab

MuxLab 500771 Manuel utilisateur

foxunhd

foxunhd SX-AEX01 Manuel utilisateur

TERK Technologies

TERK Technologies LFIRX2 Manuel utilisateur

Devolo

Devolo Audio Extender Manuel

Edimax

Edimax EW-7438RPn V2 Manuel utilisateur

Shinybow USA

Shinybow USA SB-6335T5 Manuel utilisateur

SECO-LARM

SECO-LARM ENFORCER EVT-PB1-V1TGQ Manuel utilisateur

Button Instruction:

1. ON (Green) 4. MSG (Red)

On –Device ready On –Receive “Remote”Signal

Flashing –System starting up Flashing- System warning

2. LINK (Blue) 5. Display Panel

On–Link connected On Standby –Current Channel

Flashing- Trying to connect/ no input source

3. IR (Red) 6. Menu Button (Blue)

On –Receive IR signal On-Under menu selection

Button

-

+

Menu

Short Press

*Reduce

Number

*Increase

Number

Menu/Cancel

Press together

Enter

HKM02B-4K: Quick Guide

Transmitter (Tx)

Receiver (Rx)

Note: This remote can only control either Tx or Rx.

This Process only sets up the remotes.

You don’t have to point the remote to the devices.

Step 2. Plug and Use

If there are multiple systems on the same network, please make sure

each pair is on a different channel. *Default Channel “0”

Trouble Shooting

HDCP fail: Please use the receiver remote or front panel and enable

Menu 47 “HDCP always On”function on the receiver box.

(Press: Menu -> 47 -> Enter -> 1 -> Enter)

No display: Please force 1080p 60 Hz output on the receiver box by

pressing “Menu -> 40 -> Enter -> 2-> Enter”on the receiver remote

or front panel.

Make sure the Transmitter & Receiver are on the same Channel

Reset to default “Menu -> 333 -> Enter

Point to Point Application

*MSG light will light when receive remote signal

Press &○

7at the same time

Press &○

8at the same time

*Reduce Number: switches channel or function number down

*Increase Number: switches channel or function number up

Step 1. Setup the Remote

1. Enable IGMP V2

2. Setup Jumbo Frame 8K or above

Note: Please find the instruction on the Ethernet switch manual or see the setup example

under the trouble shooting section in the manual

Multi to Multi Application

Step 1. Setup the Remote

Transmitter (Tx)

Receiver (Rx)

Press &○

7at the same time

Press &○

8at the same time

Note: This remote can only control either Tx or Rx

Step 4. Connect Transmitter & Receiver to Gigabit

Mangement Switch

Step 3. Setup the Gigabit Mangement Switch

Step 5. Download the Software

PC Software: http://tiny.cc/n5gc0y

Mobile App: B&W Video Wall Control

Android IOS

Step 2. Setup the Transmitter Box to the Desired Channel

Transmitter:

Press “+”or “-“to the desired channel number and

Press “+”and “-“at the same time to confirm (enter)

# Each Transmitter has to be on a different Channel

Receiver:

Press “+”or “-“to the desired channel number and

Press “+”and “-“at the same time to confirm (enter)