Sawn Craft Micro F-16 Guide de l'utilisateur
Revised 2013-12-30
Micro F-16 Assembly
and Setup Manual
Specifications
Recommended Power System
Wingspan
12”
RX/ESC/Servo
Spektrum AR6400 (or similar)
Overall Length
17.28”
Motor
Parkzone P-51 Motor & Gearbox (PKZ3624)
Wing Area
66.86 in2
or
Flying Weight
1.1oz
Hobbyzone Champ Motor & Gearbox (HBZ4930)
Intended Use
Indoor/Calm Winds
Battery
160mAh 1S 3.7V 25C LiPo (or similar)
Thank you from Sawn Craft.
Thank you for purchasing the Sawn Craft Micro F-16 aircraft. Like the full-scale USAF F-16, in your hands
is a remarkably versatile airplane designed to deliver a pleasure cruiser with an incredible look. The
lightweight and rigid EPS and carbon construction makes it possible for you to experience a wide
performance envelope. This means that no matter how you like to fly, you’ll enjoy both stability and
maneuverability without any sacrifice in precision or control feel.
Your Sawn Craft Micro F-16 aircraft represents the benchmark of ultra-micro performance and aerobatic
versatility. All you have to do next is read and apply the information presented in this instruction
manual.
I sincerely hope that you enjoy your model as much as we do! If you have any troubles with these
instructions or in the setup of your model feel free to contact us and we will provide you with the
service you expect from a hobbyist-owned and operated business.
Table ofContents
1 Introduction 1
1.1 Style Conventions 1
1.2 Required Tools & Supplies 1
1.3 Required Parts for Completion 2
1.4 Included Parts Description 3
2 Assembly Instructions 4
2.1 Fuselage Lamination 4
2.2 Wing Reinforcement Lamination 5
2.3 Elevator/Elevon & Rudder Hinging 6
2.4 Skid Installation 9
2.5 Fuselage Installation 10
2.6 Vertical Stabilizer Installation 11
2.7 Electronics Installation 12
3 Setup and Tuning 14
3.1 Center of Gravity 14
3.2 Control Throws and Expo 14
3.3 Launching 14
3.4 Flying Tips 15
3.5 Decorating/Finishing 15
3.6 Spare Parts 15
Sawn Craft Micro F-16 Manual
Page 1 1311101 Micro F-16 Manual.docx
1 Introduction
The contents of this manual assume the operator will have the following prerequisites:
Understanding of all appropriate safety procedures and requirements
The ability to follow written procedures and possess basic hobby building skills
1.1 Style Conventions
Below are the important style conventions that will be used throughout the guide.
Note: Key points or hints for success will be formatted in this manner.
Warning: Any area that poses either a physical hazard or the danger will be formatted in this manner.
Arrows inform where to click or to perform the specified operation.
Circled items inform of items of interest for the specified operation. Circled items will typically be
accompanied by text further identifying the region of interest.
1.2 Required Tools & Supplies
The list below contains all of the required tools and supplies that are required for the assembly and
tuning of this model.
Clean, flat work surface
#11 hobby knife
Straight-edge ruler
Soldering iron & solder
Heat gun
Wire cutters
Needle nose pliers
Foam-safe adhesive
Clear packing tape
200-grit Sandpaper on sanding block
Sawn Craft Micro F-16 Manual
Page 2 1311101 Micro F-16 Manual.docx
Sawn Craft recommends the use of Beacon Foam-Tac adhesive and 3M Blenderm Hinge Tape for the
construction of this model due to its strength, light weight, and easy use. Both Blenderm and Foam-
Tac can be purchased by visiting the Building Supplies tab on Sawn-Craft.com
1.3 Required Parts for Completion
This model was designed with the intention of putting to use the electronics that are used in today’s
popular 1S LiPo-powered Ultra-Micro aircraft. Once you have worn out the airframe on your
Hobbyzone© Champ or Parkzone© UM P-51 Mustang, simply remove the electronics and use them to
power this model. If you choose to purchase your power system components separately, Sawn Craft
does offer the Micro Electronics Kit that includes every part of the power system that you need. The list
below contains all of the required and recommended parts for the successful operation of this model.
1S LiPo “Brick”
Ultra-Micro Motor and Gearbox
Propeller
1S LiPo Battery
Please note that other power systems and components may be compatible and may work without
issue, but the listed components have been used successfully by Sawn Craft.
Optional Parts for Completion
To make your build easier and ensure the nicest looking finished product, the following products are
offered on Sawn Craft.com. See the Building Supplies tab for these products.
6” 1S Battery Lead Extension
5” Micro Motor Lead Extension
Colored Packing Tape
Sawn Craft Micro F-16 Manual
Page 3 1311101 Micro F-16 Manual.docx
1.4 Included Parts Description
Please inspect your kit and ensure that all listed parts are present and undamaged. If you find missing
a) Main Wing
b) KFm Step
c) Fuselage Half (2 each)
d) Vertical Stabilizer (2 each)
e) Elevator
f) Elevon (2 each)
g) Skid (2 each)
h) Vertical Stab Angle Template & Foot (2 each)
i) Micro Control Horn (4 each)
j) 2” x 0.024” Control Wire with Z-Bend (2 each)
k) 5” 0.051” Carbon Rod (2 each)
l) 6” 0.083” Carbon Rod
m) 1.5” 3mm Heat Shrink Tube (4 each)
n) 12” Micro Wire
o) 2” 1mm Heat Shrink Tube (2 each)
a
b
c
d
e
f
g
h
Sawn Craft Micro F-16 Manual
Page 4 1311101 Micro F-16 Manual.docx
2 Assembly Instructions
The order of assembly presented in this instruction has been tested and it is recommended that you
do not differ from them to provide the most accurate and easiest assembly possible.
2.1 Fuselage Lamination
Parts Required:
oFuselage Half (2 each)
o6” 0.083” Carbon Rod
1) Lay both fuselage halves flat on the table with the recessed slot facing up. Apply a bead of glue
around the entire perimeter of one of the fuselage halves.
2) Press the unglued fuse half onto the glued fuse half, recessed slots facing each other, and gently
slide the parts around to spread the glue evenly.
3) Separate the two fuse halves and insert the carbon rod into one of the recessed slots.
4) Rejoin the two fuse halves, glue side toward each other, ensuring that the carbon rod already in
the slot aligns with the recessed slot on the other fuse half. Set the assembled fuse lamination
aside to allow the glue to cure. If desired you can place a flat weight (book, etc.) on top of the
lamination while curing to ensure a flat assembly.
5) Once cured, sand leading edges to your liking.
Sawn Craft Micro F-16 Manual
Page 5 1311101 Micro F-16 Manual.docx
2.2 Wing Reinforcement Lamination
Parts Required:
oMain Wing
oKFm Step
1) Lay the main wing on the table with the front-to-back vertical stabilizer location markings slot
facing up. Apply a bead of glue around the entire perimeter of the KFm Step.
2) Press the glued side of the KFm onto the Main Wing, aligning the leading edges of both parts, and
gently slide the parts around to spread the glue evenly.
3) Set the assembled fuse lamination aside to allow the glue to cure. If desired you can place a flat
weight (book, etc.) on top of the lamination while curing to ensure a flat assembly.
4) Once cured, sand leading edges to your liking.
Sawn Craft Micro F-16 Manual
Page 6 1311101 Micro F-16 Manual.docx
2.3 Elevator/Elevon & Rudder Hinging
Parts Required:
oElevator
oVertical Stabilizer
oMicro Control Horn (2 each)
oMain Wing
or
oElevon (2 each)
oMicro Control horn (2 each)
oMain Wing
Elevator/Rudder Setup
Warning: This process involves using extremely sharp cutting blades. Care must be taken to avoid injury.
1) Lay the elevator on the table with the leading edge facing yourself and the control horn slot to the
left. Use a straight edge ruler and a hobby knife or a sanding block to cut an approximate 45° bevel
into the leading edge of the control surface. Set elevator aside.
Sawn Craft Micro F-16 Manual
Page 7 1311101 Micro F-16 Manual.docx
2) Lay the vertical stabilizer on the table with the bottom facing you. Carefully crack the rudder along
the rudder line or use a straight edge ruler and a hobby knife to cut down the rudder cut line in
order to separate the rudder. Remove the lower rudder extension below the control horn slots
using the same technique.
3) Lay the rudder on the table with the leading edge facing you. Use a straight edge ruler and a
hobby knife to cut an approximate 45° bevel into the leading edge of the control surface, ensuring
that the bevel is on the correct side.
If you choose to use a glue hinge for your surfaces ensure you bevel the mating surface as well.
4) Place the vertical stabilizer and rudder back together with trailing and leading edges touching,
oriented the proper direction for the bevel to face to the left when installed. Cut approx. ¼” x 1”
pieces of hinge tape. Use two of these small pieces of tape to attach the smooth sides of the
rudder and vertical stab together. Flip the assembly over and install two additional pieces of tape
on the bevel side of the hinge to complete the tape hinge. Dry fit a micro control horn into the
slot, ensuring that the hinge bevel is facing down. Set assembly aside.
Tape hinge
Table des matières
Autres manuels Sawn Craft Jouet
Sawn Craft
Sawn Craft Micro F-22 Guide de l'utilisateur
Sawn Craft
Sawn Craft Mana-Tee Guide de l'utilisateur
Sawn Craft
Sawn Craft Micro F-4D Skyray Guide de l'utilisateur
Sawn Craft
Sawn Craft Micro B-58 Guide de l'utilisateur
Sawn Craft
Sawn Craft Zero 32 Guide de l'utilisateur
Sawn Craft
Sawn Craft Micro Eurofighter Guide de l'utilisateur
Sawn Craft
Sawn Craft Mini 4-Fitt Guide de l'utilisateur
Sawn Craft
Sawn Craft Micro Gloster Javelin Guide de l'utilisateur
Sawn Craft
Sawn Craft Cherokee 24 Guide de l'utilisateur
