Satel CR-MF5 Manuel utilisateur
CR-MF5
Keypad with MIFARE proximity card reader cr-mf5_sii_en 11/23
Quick installation guide
Full manual is available on www.satel.pl.Scan the QR code to go
to our website and download the manual.
The CR-MF5 keypad can operate as:
•INT-SCR partition keypad in the INTEGRA alarm system,
•ACCO-SCR keypad with proximity card reader in the ACCO access control system,
•keypad with proximity card reader in systems of other manufacturers,
•standalone door control module.
Before you mount the keypad, program the settings required for the selected operating mode
in the CR SOFT program. The exception is a keypad that is to operate in the ACCO NET
system and is to be connected to the ACCO-KP2 controller using the RS-485 bus (OSDP
protocol). The OSDP protocol is supported by the ACCO-KP2 controllers with firmware
version 1.01 (or newer). In that case, you can program the required settings in the
ACCO Soft program (version 1.9 or newer).
Installation
The device should be installed by qualified personnel.
Prior to installation, please read the full manual.
Disconnect power before making any electrical connections.
1. Open the keypad enclosure.
2. Connect the keypad to the computer. Use the USB / RS-485 converter (e.g. ACCO-USB
by SATEL). Follow the instructions in the converter manual.
Do not connect more than 24 access control devices with the MIFARE card reader
(CR-MF5 and CR-MF3) to the converter. The CR SOFT program may not be able to
support more devices correctly.
3. Program the keypad in the CR SOFT program.
3.1. Create a new project or open an existing project.
3.2. Establish connection between the program and the device.
3.3. Program the settings and upload them to the keypad.
4. Disconnect the keypad from the computer.
5. Run the cables to where you want to install the keypad. To connect the RS-485 bus,
we recommend using a UTP cable (unshielded twisted pair). To make other connections,
use unshielded straight-through cables.
2 CR-MF5 SATEL
6. Place the enclosure base against the wall and mark the location of mounting holes.
7. Drill the holes in the wall for wall plugs (anchors).
8. Run wires through the opening in the enclosure base.
9. Use wall plugs and screws to secure the enclosure base to the wall. Select wall plugs
specifically intended for the mounting surface (different for concrete or brick wall, different
for plaster wall, etc.).
10.Connect the wires to the keypad terminals (see: “Description of terminals”).
11.Close the keypad enclosure.
12.If necessary, program the settings required for the keypad to operate in the selected
system.
The ACCO Soft program in version 1.9 (or newer) enables programming of all the
required settings. If it is to be used, you can skip the steps 2-4.
Description of terminals
Description of terminals for keypad in the INTEGRA system
Terminal
Description
NC
relay output normally closed contact
C
relay output common contact
NO
relay output normally open contact
DATA/D1
data [INT-SCR interface]
RSA
RS-485 bus terminal [OSDP]
RSB
RS-485 bus terminal [OSDP]
TMP
not used
+12V
+12 VDC power input
COM
common ground
CLK/D0
clock [INT-SCR interface]
IN1
NC type door status input
IN2
NO type request-to-exit input
IN3
not used
BELL
OC type output
SATEL CR-MF5 3
Description of terminals for keypad in the ACCO system
Terminal
Description
NC
not used
C
not used
NO
not used
DATA/D1
data [ACCO-SCR interface]
RSA
RS-485 bus terminal [OSDP]
RSB
RS-485 bus terminal [OSDP]
TMP
not used
+12V
+12 VDC power input
COM
common ground
CLK/D0
clock [ACCO-SCR interface]
IN1
not used
IN2
not used
IN3
not used
BELL
OC type output
Description of terminals for keypad in other manufacturer’s system
Terminal
Description
NC
not used
C
not used
NO
not used
DATA/D1
data (1) [Wiegand interface]
RSA
RS-485 bus terminal [OSDP]
RSB
RS-485 bus terminal [OSDP]
TMP
tamper output
+12V
+12 VDC power input
COM
common ground
CLK/D0
data (0) [Wiegand interface]
IN1
programmable input [Wiegand interface]
IN2
programmable input [Wiegand interface]
IN3
programmable input [Wiegand interface]
BELL
OC type output
4 CR-MF5 SATEL
Description of terminals for the standalone door control module
Terminal
Description
NC
relay output normally closed contact
C
relay output common contact
NO
relay output normally open contact
DATA/D1
not used
RSA
RS-485 bus terminal [OSDP]
RSB
RS-485 bus terminal [OSDP]
TMP
tamper output
+12V
+12 VDC power input
COM
common ground
CLK/D0
not used
IN1
door status input
IN2
request-to-exit input
IN3
not used
BELL
OC type output
The declaration of conformity may be consulted at www.satel.pl/ce
SATEL sp. z o.o. • ul. Budowlanych 66 • 80-298 Gdańsk • POLAND
tel. +48 58 320 94 00
www.satel.pl
Autres manuels pour CR-MF5
1
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Satel Clavier
Satel
Satel INT-KSG Guide de l'utilisateur
Satel
Satel ABAX 2 Manuel utilisateur
Satel
Satel INT-TSG Guide de l'utilisateur
Satel
Satel PERFECTA Manuel utilisateur
Satel
Satel INT-S Series Manuel utilisateur
Satel
Satel INT-SCR-BL Manuel utilisateur
Satel
Satel INT-SCR Manuel utilisateur
Satel
Satel INT-TSG Manuel utilisateur
Satel
Satel INT-TSG2 Manuel du propriétaire
Satel
Satel INT-TSH Manuel utilisateur
Satel
Satel PRF-LCD-WRL Manuel utilisateur
Satel
Satel VERSA-LCDM-WRL Manuel utilisateur
Satel
Satel INT-KLCDK-GR Manuel utilisateur
Satel
Satel VERSA-LCDM-WRL Manuel utilisateur
Satel
Satel INT-TSG2 Manuel utilisateur
Satel
Satel INT-TSI Guide de l'utilisateur
Satel
Satel INT-TSI Manuel utilisateur
Satel
Satel INT-TS Manuel utilisateur
Satel
Satel INT-SF Manuel utilisateur
Satel
Satel INT-TSG Manuel utilisateur
